EN ISO 20536-2017 en Footwear - Critical substances potentially present in footwear and footwear components - Determination of phenol in footwear materials.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Footwear - Critical substances potentially present in footwear and footwear components - Determination of phenol in footwear materials (ISO 20536:2017)BS EN ISO 20536:2017National forewordThis British Standard is the UK

2、 implementation of EN ISO 20536:2017. It is identical to ISO 20536:2017.The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear analytical grade for the solvents.5.1.1 Phenol CAS: 108-95-2 (target compound).5.1.2 Phenol-D6 CAS: 13127-88-3 (extraction surrogate).

3、5.1.3 Anthracene-D10 CAS: 1719-06-8 (internal standard).5.1.4 Toluene CAS: 108-88-3 (solvent).5.1.5 Acetone CAS: 67-64-1 (solvent).5.1.6 Mixture toluene/acetone (80/20) percent by volume (extraction mixture).The composition of the mixture is based on the volume. For example, to make 100 ml of the mi

4、xture, mix 80 ml of toluene with 20 ml of acetone.5.1.7 Methanol CAS: 67-56-1 (solvent).5.2 Stock solutions5.2.1 Internal standard Anthracene-D10 stock solution (1 000 mg/l).Weigh 10 mg of Anthracene-D10 in a 10 ml volumetric flask and fill to the mark with acetone. Transfer the content to an amber

5、10 ml vial with a polytetrafluoroethylene (PTFE) stopper and store at 4 C.5.2.2 Internal standard Anthracene-D10 working solution (10 mg/l).Prepare a 1:100 dilution of the stock solution (5.2.1). For example, take 100 l of the stock solution in a 10 ml volumetric flask and fill to the mark with acet

6、one.5.2.3 Extraction surrogate Phenol-D6 stock solution (1 000 mg/l).Weigh 10 mg of Phenol-D6 in a 10 ml volumetric flask and fill to the mark with acetone. Transfer the content to an amber 10 ml vial with PTFE stopper and store at 4 C.5.2.4 Extraction surrogate Phenol-D6 working solution (10 mg/l).

7、Prepare a 1:100 dilution of the stock solution (5.2.3). For example, take 100 l of the stock solution in a 10 ml volumetric flask and fill to the mark with acetone.5.2.5 Target compound phenol stock solution (1 000 mg/l).Weigh 10 mg of phenol in a 10 ml volumetric flask and fill to the mark with ace

8、tone. Transfer the content to an amber 10 ml vial with PTFE stopper and store at 4 C.2 ISO 2017 All rights reservedBS EN ISO 20536:2017ISO 20536:2017(E)5.2.6 Phenol + Phenol-D6 intermediate calibration solution (10 mg/l).Take a volume of 100 l of the stock solution of the extraction surrogate (5.2.3

9、) and the target compound (5.2.5) in a 10 ml volumetric flask and fill to the mark with the mixture of toluene/acetone (80/20).5.2.7 Phenol + Phenol-D6 working calibration solution (1 mg/l).Take a volume of 1 000 l of the intermediate calibration solution (5.2.6) in a 10 ml volumetric flask and fill

10、 to the mark with the mixture of toluene/acetone (80/20).6 ApparatusUsual lab equipment and the following. Use laboratory glassware in accordance with ISO 4787.6.1 Analytical balance, with an accuracy of at least 0,1 mg.6.2 Glass vial, which can be tightly sealed, 40 ml.6.3 Ultrasonic bath, with adj

11、ustable temperature.6.4 PTFE-membrane filter, pore width 0,45 m.6.5 2 ml sample vials, PTFE-capped.6.6 20 ml sample vials, PTFE-capped.6.7 Gas chromatograph with a mass selective detector (MSD). Other chromatographic technics may be used provided that they have been validated for this analysis.7 Sam

12、plingIn the footwear, the upper and the complex lining plus the insock shall be tested.The test piece consists of a single material (leather, textile or polymer). Homogenous textile, leather and polymer samples are cut into pieces with an edge length of up to 5 mm.The sample should not be subjected

13、to grinding as it results in the loss of volatile phenol.8 Test method8.1 ExtractionWeigh 1 g of the sample in a 20 ml glass vial (6.6). Then add 9,8 ml of the extraction mixture (5.1.6) and 200 l of the extraction surrogate working solution (5.2.4).The extraction is conducted with an ultrasonic dev

14、ice at 60 C 5 C during 60 min 2 min.NOTE It has been proven that acetone is efficient as extraction solvent. However, its high polarity (compared to the extraction mixture) can conduct to a high amount of co-extracted compounds (such as dyes or other polar compounds like glycols) which could disturb

15、 the analysis.Some polymeric materials can be dissolved in the extraction mixture and can cause problems during the quantification. In these cases, precipitation by methanol could be necessary. Precipitate the solution obtained by adding 20 ml of methanol (5.1.7) and allow the precipitate to settle

16、for at least 5 min. Filtrate, if necessary, using a 0,45 m PTFE filter. ISO 2017 All rights reserved 3BS EN ISO 20536:2017ISO 20536:2017(E)8.2 AnalysisTake an aliquot of exactly 1 ml of the extract and add 50 l of the internal standard working solution (5.2.2).Analyse with GC-MS (6.7) according to C

17、lause 9.8.3 CalibrationFor practical reasons the calibration is based on a solution containing the target compound and the extraction surrogate.Within the linear range use at least five measurements at different concentrations. The calibration is conducted directly in 2 ml sample vials, see Table 1.

18、Table 1 Calibration solutionsStandard L1 L2 L3 L4 L5Volume of the working calibration solution (l) (5.2.7)50 100 250 500 1 000Volume of extracting mixture (l) (5.1.6)950 900 750 500 0Concentration of phenol and Phenol-D6 (g/l) 50 100 250 500 1 000Volume of the internal standard working solution (l)

19、(5.2.2)50Concentration of the internal standard (g/l) 5009 Determination with GC-MS9.1 Measuring methodValidated analysis methods other than the method described in Annex A are permitted, provided a comparable precision and quantification limit (9.3.1) can be reached.The ions given in Table 2 shall

20、be used.Examples are given in Annex A.Table 2 Monitoring ionsCompounds IonsPhenol9466Phenol-D69971Anthracene-D10 1884 ISO 2017 All rights reservedBS EN ISO 20536:2017ISO 20536:2017(E)9.2 Quantification9.2.1 Calibration curveSet up the linear regression function by using the following ratio (A e/A is

21、) and (C e/C is) with the help of Formula (1):AAabCCeiseis=+ (1)whereAeis the area of the target of phenol based on the monitoring ions;Aisis the area of the peak of Anthracene-D10 based on the monitoring ions;Ceis the concentration of phenol in the calibration standard, in g/l;Cisis the concentrati

22、on of Anthracene-D10 in the calibration standard, in g/l;a is the slope of the linear function;b is the ordinate intercept of the calibration curve. The units depend on the evaluation.The same calculation shall be conducted for Phenol-D6.9.2.2 Recovery rateThe use of an extraction surrogate permits

23、the calculation of an extraction yield using Formula (2):RCC%()=calculatedtheoretical100 (2)whereCcalculatedis the concentration of Phenol-D6 analysed in the sample after the extraction;Ctheoreticalis the concentration of Phenol-D6 initially introduced before the extraction (200 l of a 10 mg/l solut

24、ion into 10 ml of extraction mixture; in this case Ctheoreticalis 200 g/l).If the extraction is below 75 % or above 125 %, the sample shall be reanalysed.9.2.3 Determination of the phenol contentThe content of phenol is calculated according to Formula (3) as a mass fraction W in mg/kg:WVmaCAAb=(/)ec

25、hisis(3)whereW is the content of the phenol in the specimen, in mg/kg;V is the volume of extraction mixture used for the extraction, in ml (in most cases this value will be equal to 10 ml);m is the mass of the test specimen, in kg;Aechis the area of the peak of phenol in the sample;Aisis the area of

26、 the peak of Anthrancene-D10 in the sample;Cisis concentration of Anthrancene-D10 in the sample, in g/l;a is the slope of the linear function determined in (9.2.1);b is the ordinate intercept of the calibration curve determined in (9.2.1). ISO 2017 All rights reserved 5BS EN ISO 20536:2017ISO 20536:

27、2017(E)9.3 Performances of the test method9.3.1 Quantification limit of the GC-MS methodThe quantification limit of the method should be 0,5 mg/kg considering a mass of sample of 1 g and an extraction volume of 10 ml.It can be lowered by concentrating the sample solution. This is done by reducing th

28、e extraction volume to 1 ml under a gentle stream of nitrogen.9.3.2 Interlaboratory testsThe results of the interlaboratory tests are given in Annex B.10 Test reportThe test report shall contain the following information:a) a reference to this document, i.e. ISO 20536;b) the date of the test;c) all

29、the details necessary for complete identification of the sample tested;d) the different material types (see Clause 7) that have been tested;e) the condition of storage before the test, if available;f) a determination of the extracted phenol as calculated in 9.2.3;g) deviations from the method specif

30、ied in this document.6 ISO 2017 All rights reservedBS EN ISO 20536:2017ISO 20536:2017(E)Annex A (informative) Example of an instrumental methodA.1 GeneralThe phenol and Phenol-D6 are analysed by gas chromatography/mass spectrometry on a single quad/MS use in a simultaneous SIM/SCAN mode.A.2 Chromato

31、graphic conditionsColumn: DB-5MS (or equivalent-5 %phenyl-95 %dimethylpolysiloxane).Dimension: 30 m 0,25 mm 0,25 m.Carrier gas: Helium with a linear velocity of 36 cm/s.Oven:50 C during 1 min.245 C at 15 C/min.300 C at 25 C/min during 4 min.Injector: 265 C in pulse splitless mode with an injection v

32、olume of 1 l.Pulse pressure: 120 kPa during 1,5 min.Split flow: 60 ml/min at 1,5 min.NOTE In order to get a suitable separation between toluene and phenol, another column with a more polar phase could be used, such as DB-35 (35 % phenyl), VF-17 (50 % phenyl) or DB-WAX (100 % polyethylene glycol).A.3

33、 Detection conditionsTransfer line: 280 C.The single quad MS works in simultaneous SIM/SCAN mode.The mass SCAN range is between 50 m/z and 300 m/z.The SIM mode focus on the ions is given in Table 2. ISO 2017 All rights reserved 7BS EN ISO 20536:2017ISO 20536:2017(E)Key1 phenol and Phenol-D62 Anthran

34、cene-D10Figure A.1 Total ion chromatogram (TIC) of a standard at 500 g/l8 ISO 2017 All rights reservedBS EN ISO 20536:2017ISO 20536:2017(E)Annex B (informative) Results of the interlaboratory testsThe results obtained from two separate interlaboratory trials are given in Table B.1.Table B.1 Precisio

35、n data from trialsMaterialDate of the ILTNumber of laboratoryMean valueamg/kgRobust standard deviationamg/kgUncertainty type , u(x)amg/kgTex tile 06/2015 9 13,2 0,7 3,1Leather 03/2016 7 15,3 1,9 0,9Leather 03/2016 7 12,5 1,6 0,8Coated textile 03/2016 9 15,1 4,4 1,8Key ILT: Interlaboratory trial.aIn

36、accordance with ISO 13528:2015, Annex C using a robust algorithm. ISO 2017 All rights reserved 9BS EN ISO 20536:2017ISO 20536:2017(E)Bibliography1 ISO/TR 16178:2012, Footwear Critical substances potentially present in footwear and footwear component2 ISO 13528:2015, Statistical methods for use in pr

37、oficiency testing by interlaboratory comparisons10 ISO 2017 All rights reservedBS EN ISO 20536:2017This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services

38、.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expe

39、rtise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on stan

40、dardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including Brit

41、ish and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicatio

42、nsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publi

43、cation and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written c

44、onsent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named us

45、er only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reprod

46、uced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permiss

47、ion to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instan

48、t access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in

49、single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-Use