EN ISO 22774-2004 en Footwear - Test methods for accessories shoe laces - Abrasion resistance《鞋靴 附件的试验方法 鞋带 耐磨性 ISO 22774-2004》.pdf

1、BRITISH STANDARD BS EN ISO 22774:2004 Footwear Test methods for accessories: shoe laces Abrasion resistance The European Standard EN ISO 22774:2004 has the status of a British Standard ICS 61.060 BS EN ISO 22774:2004 This British Standard was published under the authority of the Standards Policy and

2、 Strategy Committee on 20 December 2004 BSI 20 December 2004 ISBN 0 580 45124 0 National foreword This British Standard is the official English language version of EN ISO 22774:2004. It is identical with ISO 22774:2004. The UK participation in its preparation was entrusted to Technical Committee TCI

3、/69, Footwear and leather, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in th

4、e BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible

5、for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK i

6、nterests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright notice displayed in

7、this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO22774 December2004 ICS61.060 Englishversion FootwearTestmethodsforaccessories:shoelacesAbrasion resistance(ISO22774:2004) Chaussure

8、sMthodesdessaipouraccessoires:lacetset oeilletsRsistancelabrasion(ISO22774:2004) SchuhePrfverfahrenfrZubehr:Schnrsenkel Scheuerbestndigkeit(ISO22774:2004) ThisEuropeanStandardwasapprovedbyCENon23August2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsfor

9、givingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioni

10、nanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Icel

11、and,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allr

12、ightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO22774:2004:EEN ISO 22774:2004 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle4 5 Apparatus and materials.5 5.1 General5 6 Test specimens7 6.1 Method 1

13、 .7 6.2 Methods 2 and 3.7 7 Conditioning.7 8 Procedure .7 8.1 Method 1 .7 8.2 Method 2 .8 8.3 Method 3 .8 9 Calculation and expression of results.8 10 Test report 9 Annex ZA (normative) Normative references to International publications with their corresponding European publications10 EN ISO 22774:2

14、004 (E) 3Foreword This document (EN ISO 22774:2004) has been prepared by CEN/TC 309, “Footwear“, the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 216 “Footwear“. This European Standard shall be given the status of a national standard, either by publication

15、of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europea

16、n Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN ISO 22774:200

17、4 (E) 4 1 Scope This document specifies three test methods for determining the abrasion resistance of a shoe lace to repeated rubbing: Method 1: lace to lace abrasion; Method 2: lace to standard eyelet abrasion; Method 3: lace to eyelet (from footwear) abrasion. 2 Normative references The following

18、referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12222, Footwear Standard atmospheres for conditioning and te

19、sting of footwear and components for footwear 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 abrasion resistance of shoe laces ability of the shoe lace to resist to repeated rubbing against either a similar shoe lace or a lace carrier 3.2 nu

20、mber of cycles to failure arithmetic mean of the number of cycles to failure for the test specimens submitted to test 3.3 type of failure expressed as failure of the shorter lace or failure of the longer lace, together with a description of the respective amount of wear in the covering and core of e

21、ach lace 4 Principle A shoe lace is threaded through a loop formed by: - a piece of similar lace held open by a spacer (Method 1); - a lace carrier (Methods 2 and 3). The shoe lace is bent through a fixed acute angle at the point of contact with the loop. It is then held under a standard tension whi

22、le it is repeatedly drawn back and forth through the loop until it fails. EN ISO 22774:2004 (E) 5 5 Apparatus and materials 5.1 General 5.1.1 A test machine with one or more test stations, see Figure 1, each having: NOTE Test machines with less than six stations are also acceptable to conduct this t

23、est. In which case the test should be repeated until six test specimens have been tested (see 8.1.6). 5.1.2 A moveable clamp which has a means of firmly holding: - both ends of a piece of shoe lace (Method 1); - one end of the metal strip (see 5.1.8) (Methods 2 and 3). 5.1.3 A stationary clamp which

24、 is mounted in the horizontal same plane as the moveable clamp (5.1.1) and is capable of holding one end of a shoe lace. The stationary clamp should be 280 mm 50 mm from the moveable clamp (5.1.2) when the clamps are at their minimum separation, this distance will subsequently be referred to as D. 5

25、.1.4 A tensioning device with a method of holding the end of a piece of shoe lace at a point 35 mm 5 mm to one side of, and in the same horizontal plane as, the stationary clamp (5.1.3) and applying a tensioning force of 2,45 N 0,03 N, see Figure 1. This can be achieved by passing the shoe lace over

26、 a pulley and suspending a mass of 250 g 3 g from the lower end of the vertical portion of the lace. 5.1.5 A means of moving the moveable clamp (5.1.2) with a simple harmonic reciprocating motion through a distance of 35 mm 2 mm and back to the original starting position at a rate of 60 cycles per m

27、inute 6 cycles per minute. 5.1.6 A means of counting the number of abrasion cycles up to failure of the lace or lace carrier. 5.1.7 For Method 1: - a rigid spacer device of width 25 mm 5 mm. This is used to hold the two legs of the loop of lace which is clamped in the moveable clamp (5.1.2) apart (s

28、ee Figure 1), so that when it is under tension the end of the loop forms an isosceles triangle with the spacer as its base and the two parts of the lace are at an angle of 52,5 5,0; - a template with an angle of 52,5 marked on it, for setting the position of the spacer device. 5.1.8 For Method 2, a

29、metal strip of width approximately 25 mm, thickness approximately 1 mm and length approximately D 60 mm. One end of the strip should fit into the moveable clamp (5.1.2) and the other end should be capable of holding the test lace carrier. EN ISO 22774:2004 (E) 6 X = Method 1: Lace lace abrasion Y =

30、Methods 2 and 3: Lace carrier abrasion 1 Lace loop 2 Spacer 3 Force (2,45 N 0,03 N) 4 Stationary clamp 5 Moveable clamp 6 Metal strip 7 Lace carrier 8 Force (2,45 N 0,03 N) Figure 1 Plan view of abrasion geometry 5.2 Standard eyelets, with the following characteristics (method 2): Construction: Visi

31、ble (standard/flat) type; Material type: brass; Nominal internal barrel diameter: 4,5 mm; Nominal overall length: 5,5 mm; 5.3 Six test lace carriers (for methods 2 and 3) 5.3.1 Method 2 Mounting board: rigid fibreboard 3,0 mm 0,5 mm thick. Eyelet is clenched in drilled hole 5,0 mm 0,2 mm diameter (b

32、oard with eyelet cut to size to fit mounting in machine) and fixed to the metal strip (see Figure 1). EN ISO 22774:2004 (E) 7 5.3.2 Method 3 Cut from the footwear a sample including the eyelet and fix it to the metal strip (see Figure 1). 6 Test specimens 6.1 Method 1 6.1.1 Cut six pieces of shoe la

33、ce each of minimum length 2 x (D 160) mm. If sufficient made shoe laces are available, cut each test specimen from a separate lace. 6.1.2 Cut six pieces of shoe lace each of length 500 mm 10 mm. If sufficient made shoe laces are available, cut each test specimen from a separate lace. For some equipm

34、ent it is possible to use pieces of lace as short as 100 mm by tying string to each end to lengthen them, provided only the lace test specimen (6.1.1) rubs against the lace test specimen (6.1.2). 6.2 Methods 2 and 3 Cut six pieces of shoe lace each of length 300 mm 10 mm. If sufficient made shoe lac

35、es are available, cut each test specimen from a separate lace. For some equipment it is possible to use pieces of lace as short as 100 mm by tying string to each end to lengthen them, provided only the lace test specimen rubs against the test lace carrier (5.3). 7 Conditioning Store the shoe laces a

36、nd the test lace carriers in a standard atmosphere in accordance with EN 12222 for at least 48 h before testing and carry out the test in this atmosphere. 8 Procedure 8.1 Method 1 8.1.1 Secure both ends of one of the pieces of lace (6.1.1) in a moveable clamp (5.1.2) so that it forms a loop of lengt

37、h approximately 2 x (D 160) mm. 8.1.2 Secure one end of a piece of the lace (6.1.2) in the corresponding stationary clamp (5.1.3). 8.1.3 Thread the free end of the piece of lace (6.1.2) through the loop formed by the piece of lace (6.1.1) in subclause 8.1.1. 8.1.4 Apply a tensioning force of 2,45 N

38、0,03 N to the free end of the piece of lace (6.1.2). 8.1.5 Fit a spacer (5.1.7) into the loop formed by the piece of lace (6.1.1) and slide it towards the point of contact with the piece of lace (6.1.2) until the template (5.1.7) indicates that the tip of the loop of lace (6.1.1) forms an angle of 5

39、2,5 5,0 (see Figure 1). 8.1.6 Repeat the procedure in 8.1.1 to 8.1.5 for the other 5 pairs of test laces (6.1.1 and 6.1.2). For equipment with less than six test stations this will require steps 8.1.1 to 8.1.4 to be repeated until all six pieces have been tested. EN ISO 22774:2004 (E) 8 8.1.7 Reset

40、the counter(s) (5.1.6) and start the test machine (5.1). 8.1.8 Stop the test when all the lace test specimens (8.1.6) have failed. 8.1.9 For each lace test specimen record the number of cycles to failure and the type of failure (3.3). 8.2 Method 2 8.2.1 Fix a test lace carrier (5.3.2) (including the

41、 standard eyelet) to one end of each of the metal strips (5.1.8) so that the relative orientation between the carrier and the metal strip is the same as the orientation between the carrier and the facing in the completed shoe. 8.2.2 Clamp the other end of a metal strip into each of the moveable clam

42、ps (5.1.2) so that the lace carrier is approximately D 60 mm from the moveable clamp. 8.2.3 Follow the procedure in 8.1.2 to 8.1.4 for each of the six pieces of lace (6.2) but thread them through the lace carriers (5.3) instead of the pieces of lace. For machines with less than six test stations, se

43、e 8.1.6. 8.2.4 Follow the procedure in 8.1.7 to 8.1.8. 8.2.5 For each lace test specimen record the number of cycles to failure, the type of failure (3.3) and any damage to the test lace carriers. 8.3 Method 3 8.3.1 Fix a test lace carrier (5.3.3) (including the sample cut from the footwear) to one

44、end of each of the metal strips (5.1.8) so that the relative orientation between the carrier and the metal strip is the same as the orientation between the carrier and the facing in the completed shoe. 8.3.2 Clamp the other end of a metal strip into each of the moveable clamps (5.1.2) so that the la

45、ce carrier is approximately D 60 mm from the moveable clamp. 8.3.3 Follow the procedure in 8.1.2 to 8.1.4 for each of the six pieces of lace (6.2) but thread them through the lace carriers (5.3) instead of the pieces of lace. For machines with less than six test stations, see 8.1.6. 8.3.4 Follow the

46、 procedure in 8.1.7 to 8.1.8. 8.3.5 For each lace test specimen record the number of cycles to failure, the type of failure (3.3) and any damage to the test lace carriers. 9 Calculation and expression of results Calculate the arithmetic mean of the rubbing cycles (recorded in 8.1.9, 8.2.5 and 8.3.5)

47、 required to abrade through each of the six test specimens. EN ISO 22774:2004 (E) 9 10 Test report The test report shall include the following information: a) reference to this document, EN ISO 22774; b) test method Method 1: lace to lace abrasion or Method 2: lace to standard eyelet abrasion or Met

48、hod 3: lace to eyelet (from footwear) abrasion used; c) full description of: - the shoe laces (Method 1); - the shoe laces and standard eyelets (Method 2); - the shoe laces and eyelets from footwear (Method 3); d) arithmetic mean of the number of abrasion cycles to failure (see clause 9); e) range of abrasion cycles to failure; f) type(s) of failure; g) any deviation from this test method and any incident which could affect the result; h) date of testing. EN ISO 22774:2004 (E) 10 A