EN ISO 23997-2012 en Resilient floor coverings - Determination of mass per unit area《弹性覆地材料 单位面积质量测定》.pdf

1、BRITISH STANDARDResilient floor coverings Determination of mass per unit areaICS 97.150nullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnullnullnull nullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnull nullnullnull

2、nullnullnullnullnullnull nullnullnullBS EN ISO23997:2012This British Standard is the UK implementation of EN ISO 23997:2012.It is identical to ISO 23997:2007. It supersedes BS ISO 23997:2007 and BS EN 430:1994, which are withdrawn. The UK participation in its preparation was entrusted to Technical C

3、ommittee PRI/60, Resilient floor coverings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a Br

4、itish Standard cannot confer immunity from legal obligations.BS EN ISO 23997:2012This British Standard waspublished under the authorityof the Standards Policy andStrategy Committeeon 31 January 2008 The British Standards Institution 2012. Published by BSI Standards Limited 2012.Amendments/corrigenda

5、 issued since publicationDate Comments 29 February 2012This corrigendum renumbers BS ISO 23997:2007 as BS EN ISO 23997:2012ISBN 978 0 580 75248 3EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 23997 February 2012 ICS 97.150 Supersedes EN 430:1994English Version Resilient floor coverings - D

6、etermination of mass per unit area (ISO 23997:2007) Revtements de sol rsilients - Dtermination de la masse surfacique (ISO 23997:2007) Elastische Bodenbelge - Bestimmung der flchenbezogenen Masse (ISO 23997:2007) This European Standard was approved by CEN on 31 December 2011. CEN members are bound t

7、o comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-C

8、ENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has

9、the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

10、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form

11、 and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 23997:2012: EEN ISO 23997:2012 (E) Foreword The text of ISO 23997:2007 has been prepared by Technical Committee ISO/TC 219 “Floor coverings” of the International Organization for Standardization (ISO) and has been taken o

12、ver as EN ISO 23997:2012 by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest b

13、y August 2012, and conflicting national standards shall be withdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such pa

14、tent rights. This document supersedes EN 430:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,

15、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 23997:2007 has been approved by CEN as a

16、 EN ISO 23997:2012 without any modification. 2 BS EN ISO 23997:20121Resilient floor coverings Determination of mass per unit area 1 Scope This International Standard describes a method for determining the mass per unit area of a resilient floorcovering. 2 Terms and definitions For the purposes of th

17、is document, the following terms and definitions apply.2.1 mass per unit area quotient of mass and area NOTE Mass per unit area is expressed in grams per square metre. 3 Principle A number of specimens of defined size are taken from a resilient floor-covering sample. The specimens are weighed and, f

18、rom this, the mass per unit area of the floor covering is calculated. 4 Apparatus 4.1 Balance, capable of weighing a specimen to the nearest 10 mg. 4.2 Calliper gauge, capable of measuring the size of the specimen to the nearest 0,05 mm. 5 Atmosphere for conditioning and testing Condition the specim

19、en at a temperature of 23 2 C and a relative humidity of 50 5 % for a minimum of 24 h. Maintain these conditions when carrying out the test. 6 Sampling and selection of specimens Take a representative sample from the available material. Take five specimens, at equal distances from the sample, the di

20、stance between the outer edge of the sample and the nearest edge of the specimen being atleast 100 mm, either square or round of at least 0,01 m 2 in area, or from individual tiles. If necessary, clean the edges of the specimen.Full tiles may also be used.EN ISO 23997:2012 (E) BS EN ISO 23997:20122

21、7 Test procedure For each specimen, measure and record the surface dimensions to the nearest 0,1 mm. Weigh each specimen separately and record the mass to the nearest 10 mg. 8 Calculation and expression of results Calculate the mass per unit area, in grams per square metre, using the following formu

22、la: mAwhere m is the mass of the specimen, in grams;A is the area of the specimen, in square metres. For results up to and equal to 1 000 g/m2 , express to the nearest 5 g/m2 . For results over 1 000 g/m2 , express to the nearest 10 g/m2 . Calculate the mean value for the mass per unit area for the

23、five specimens, expressed to the nearest gram. 9 Precision statementA round-robin test will be conducted to determine the precision of this method 10 Test reportThe test report shall contain the following information:a) a statement that the tests were performed in accordance with this International

24、Standard (ISO 23997); b) complete identification of the product tested, including type, source, colour and manufacturers referencenumbers;c) previous history of the sample; d) the mean value for the mass per unit area; e) anydeviation from this International Standard, which may have affected the res

25、ults.EN ISO 23997:2012 (E) BS EN ISO 23997:2012blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated

26、by Royal Charter . British Standards and other standardizationproducts are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated

27、 by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British

28、 Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating

29、 service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the

30、 website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relev

31、ant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date w

32、ith standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via Br

33、itish Standards Online can be found at information about British Standards is available on the BSI website at the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in

34、 the information used (such as the international standardization bodies) has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted i

35、n any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070 Email: