EN ISO 24598-2012 en Welding consumables - Solid wire electrodes tubular cored electrodes and electrode-flux combinations for submerged arc welding of creep-resisting steels - Clas.pdf

1、BSI Standards PublicationBS EN ISO 24598:2012Welding consumables Solidwire electrodes, tubular coredelectrodes and electrode-fluxcombinations for submergedarc welding of creep-resistingsteels Classification (ISO24598:2012)Incorporating corrigendum October 2015BS EN ISO 24598:2012 BRITISH STANDARDNat

2、ional forewordThis British Standard is the UK implementation of EN ISO24598:2012. It supersedes BS EN ISO 24598:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee WEE/39, Welding consumables.A list of organizations represented on this committee can be

3、obtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication.ISBN 978 0 580 91704 2ICS 25.160.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This Britis

4、h Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2012.Amendments/corrigenda issued since publicationDate Text affected The British Standards Institution 2015.Published by BSI Standards Limited 201531 October 2015 Implementation of ISO corrected tex

5、t 1 February 2013: See ISO foreword for detailsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 24598 May 2012 ICS 25.160.20 English Version Welding consumables - Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of creep-resisting stee

6、ls - Classification (ISO 24598:2012) Produits consommables pour le soudage - Fils-lectrodes pleins, fils-lectrodes fourrs et couples lectrodes-flux pour le soudage larc sous flux des aciers rsistant au fluage - Classification (ISO 24598:2012) Schweizustze - Drahtelektroden, Flldrahtelektroden und Dr

7、aht-Pulver-Kombinationen fr das Unterpulverschweien von warmfesten Sthlen - Einteilung (ISO 24598:2012) This European Standard was approved by CEN on 13 April 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stand

8、ard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English

9、, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bul

10、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMM

11、ITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 24598:2012: EEN ISO 24598:2012 (E

12、) 3 Foreword This document (EN ISO 24598:2012) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes“ in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given the status of a national stan

13、dard, either by publication of an identical text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn at the latest by November 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

14、ts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 24598:2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stan

15、dard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and th

16、e United Kingdom. Endorsement notice The text of ISO 24598:2012 has been approved by CEN as a EN ISO 24598:2012 without any modification. ii ISO 2012 All rights reservedBS EN ISO 24598:2012ISO 24598:2012(E) ISO 2012 All rights reserved iiiContents Page Foreword iv Introduction . v 1 Scope 1 2 Normat

17、ive references 1 3 Classification . 2 4 Symbols and requirements 2 4.1 General . 2 4.2 Symbol for the product/process 3 4.3 Symbols for the tensile properties of the all-weld metal deposit . 3 4.4 Symbols for impact properties of all-weld metal deposits . 3 4.5 Symbol for type of welding flux . 5 4.

18、6 Symbol for the chemical composition of solid wire electrodes and of all-weld metal deposits 5 5 Mechanical tests 9 5.1 Preheating, interpass and post-weld heat treatment temperatures . 9 5.2 Welding conditions and pass sequence . 12 6 Chemical analysis . 13 7 Rounding procedure . 14 8 Retests 14 9

19、 Technical delivery conditions 15 10 Examples of designation 15 Bibliography 17 BS EN ISO 24598:2012ISO 24598:2012(E) iv ISO 2012 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

20、of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-government

21、al, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The mai

22、n task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Att

23、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 24598 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 3

24、, Welding consumables. This second edition cancels and replaces the first edition (ISO 24598:2007), which has been technically revised. The main changes compared to the previous edition are: a) the composition of 9C1MV is modified on the B side of Table 3 (former Table 4) and Table 4 (former Table 5

25、); b) different test pieces in accordance with ISO 15792-1 are specified for side A and B in Clauses 5A and 5B, respectively. Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 3 via your national standards body. A

26、 complete listing of these bodies can be found at www.iso.org. In this corrected version, extraneous characters in Table 4, page 11, column Cr, 5th row from the bottom have been removed. BS EN ISO 24598:2012ISO 24598:2012(E) ISO 2012 All rights reserved vIntroduction This International Standard reco

27、gnizes that there are two somewhat different approaches in the global market to classifying a given wire electrode, tubular cored electrode or electrode/flux combination, and allows for either or both to be used to suit a particular market need. Application of either type of classification designati

28、on (or of both where suitable) identifies a product as classified in accordance with this International Standard. The classification in accordance with system A is mainly based on EN 12070:19992. The classification in accordance with system B is mainly based upon standards used around the Pacific Ri

29、m. This International Standard provides a classification system for solid wire electrodes in terms of their chemical composition, solid wire electrodes and tubular cored electrodes in terms of the deposit composition obtained with a particular submerged arc flux and, where required, electrode-flux c

30、ombinations in terms of the yield strength, tensile strength and elongation of the all-weld metal deposit. The ratio of yield to tensile strength of weld metal is generally higher than that of parent metal. Users should note that matching weld metal yield strength to parent metal yield strength does

31、 not necessarily ensure that the weld metal tensile strength matches that of the parent material. Where the application requires matching tensile strength, therefore, selection of the consumable should be made by reference to column 3 of Table 1A or Table 1B, as appropriate. Although combinations of

32、 wire electrodes and fluxes supplied by individual companies can have the same classification, the individual wire electrodes and fluxes from different companies are not interchangeable unless verified in accordance with this International Standard. It should be noted that the mechanical properties

33、of all-weld metal test pieces used to classify the wire electrodes vary from those obtained in production joints because of differences in welding procedure, such as electrode size, welding position and material composition. BS EN ISO 24598:2012INTERNATIONAL STANDARD ISO 24598:2012(E) ISO 2012 All r

34、ights reserved 1Welding consumables Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of creep-resisting steels Classification 1 Scope This International Standard specifies requirements for classification of solid wire electrodes, tubular cored

35、 electrodes and electrode/flux combinations (all-weld metal deposits) for submerged arc welding of creep resisting and low-alloy elevated-temperature steels. One electrode can be tested and classified with different fluxes. The solid wire electrode is also classified separately based on its chemical

36、 composition. This International Standard is a combined specification providing for classification utilizing a system based upon the chemical composition of the solid wire electrode and all-weld metal deposit, or utilizing a system based upon the tensile strength of the all-weld metal deposit and th

37、e chemical composition of the solid wire electrode and all-weld metal deposit obtained with the electrode/flux combination. a) Clauses, subclauses and tables which carry the suffix letter “A” are applicable only to solid wire electrodes, tubular cored electrodes and all-weld metal deposits classifie

38、d in accordance with the system based upon chemical composition. b) Clauses, subclauses and tables which carry the suffix letter “B” are applicable only to solid wire electrodes, tubular cored electrodes and all-weld metal deposits classified in accordance with the system based upon the tensile stre

39、ngth of all-weld metal deposits and the chemical composition of solid wire electrodes and all-weld metal deposits. c) Clauses, subclauses and tables which do not have either the suffix letter “A” or the suffix letter “B” are applicable to all solid wire electrodes, tubular cored electrodes and elect

40、rode/flux combinations classified under this International Standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do

41、cument (including any amendments) applies. ISO 544, Welding consumables Technical delivery conditions for filler materials and fluxes Type of product, dimensions, tolerances and markings ISO 6847, Welding consumables Deposition of a weld metal pad for chemical analysis ISO 13916, Welding Guidance on

42、 the measurement of preheating temperature, interpass temperature and preheat maintenance temperature ISO 14174, Welding consumables Fluxes for submerged arc welding and electroslag welding Classification ISO 14344, Welding consumables Procurement of filler materials and fluxes BS EN ISO 24598:2012I

43、SO 24598:2012(E) 2 ISO 2012 All rights reservedISO 15792-1, Welding consumables Test methods Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys ISO 80000-1:2009, Quantities and units Part 1: General 3 Classification Classification designations are based upon tw

44、o approaches to indicate the chemical composition of the solid wire electrode, the chemical composition of the all-weld metal deposit obtained with a solid wire electrode or tubular cored electrode, and the tensile properties and impact properties of the all-weld metal deposits obtained with a given

45、 electrode/flux combination. The two designation approaches include additional designators for some other classification requirements, but not all, as is clear from the provisions given in this International Standard. In many cases, a given commercial product can be classified in accordance with bot

46、h systems. Then either or both classification designations can be used for the product. A solid wire electrode shall be classified in accordance with its chemical composition as given in Table 3. An all-weld metal deposit from a solid wire electrode or tubular cored electrode shall be classified in

47、accordance with the all-weld metal deposit composition, as given in Table 4, obtained with a particular flux. When the solid wire electrode or tubular cored electrode is classified in combination with a flux for submerged arc welding, the classification shall be prefixed with a symbol in accordance

48、with Clause 4 as appropriate. 3A Classification by chemical composition 3B Classification by tensile strength and chemical composition The classification is divided into three parts: The classification is divided into five parts: 1) the first part gives a symbol indicating theproduct or process to b

49、e identified; 1) the first part gives a symbol indicating the product or process to be identified; 2) the second part gives a symbol indicating thechemical composition of the solid wire electrode(see Table 3) and all-weld metal deposit (seeTable 4); 2) the second part gives a symbol indicating the strength and elongation of the all-weld metaldeposit in the post-weld heat-treated condition (see Table 1B); 3) the third part gives a symbol indicating the impact properties of all-weld metal deposits in the same condition