EN ISO 28017-2018 en Rubber hoses and hose assemblies wire or textile reinforced for dredging applications - Specification.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - SpecificationBS EN ISO 28017:2018National forewordThis British Standard is the UK implementation of EN ISO 28017:2018. It is iden

2、tical to ISO 28017:2018. It supersedes BS EN ISO 28017:2011+A1:2015, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this committee can be obtained on

3、request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96980 5ICS 23.040.70; 83.140.40Compliance

4、with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 28017:2018EUROPEAN

5、STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 28017February 2018ICS 23.040.70 Supersedes EN ISO 28017:2011, EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN ISO 28017

6、:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersRubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2018)Tuyaux et flexibles en caoutchouc, armature textile ou mtallique, pour de

7、s applications de dragage - Spcifications (ISO 28017:2018)Gummischluche und Schlauchleitungen, Draht- oder Textilverstrkt fr Nassbaggeranwendungen - Anforderung (ISO 28017:2018)This European Standard was approved by CEN on 9 March 2018.CEN members are bound to comply with the CEN/CENELEC Internal Re

8、gulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN me

9、mber.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.C

10、EN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

11、 Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 28017:2018 (E)European forewordThis document (EN ISO 28017:2018) has been prepared by Technical Committee ISO/TC 45 “Rubber and plastics hoses and hose assemblies” in collabora

12、tion with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2018, and co

13、nflicting national standards shall be withdrawn at the latest by August 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes

14、EN ISO 28017:2011.According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mace

15、donia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 28017:2018 has been approved

16、 by CEN as EN ISO 28017:2018 without any modification.2BS EN ISO 28017:2018ISO 28017:2018Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Classification 24.1 Classes 24.2 Grades . 25 Materials and construction . 35.1 Hoses 35.2 Flotation material . 35.3 End fittings and end

17、 connections 46 Dimension and tolerances 46.1 Diameters 46.2 Hose assembly length 57 Physical properties 57.1 Rubber compounds . 57.1.1 Abrasion resistance of lining . 57.1.2 Tear strength of lining . 57.1.3 Rebound resilience of lining 57.1.4 Ozone resistance of cover 57.2 Performance requirements

18、67.2.1 Hydrostatic requirements 67.2.2 Change in length . 67.2.3 Bending test . 67.2.4 Leakage of hose assemblies (proof pressure test) 77.2.5 Minimum reserve buoyancy 77.2.6 Flotation material recovery 87.2.7 Adhesion between components . 87.2.8 Adhesion between end fitting and lining 87.2.9 Minimu

19、m tensile strength of empty hose assemblies . 97.2.10 Vacuum resistance 97.2.11 Dimensions of flange and other connections 97.2.12 Visual examination . 97.3 Frequency of testing . 98 Test certificate or report .109 Marking .1010 Recommendations for packaging and storage .10Annex A (normative) Type t

20、ests and routine tests .11Annex B (normative) Measurement of adhesion between end fitting and lining .12Annex C (normative) Hose assembly tensile-strength test 15Bibliography .18 ISO 2018 All rights reserved iiiContents PageBS EN ISO 28017:2018ISO 28017:2018ForewordISO (the International Organizatio

21、n for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has

22、 the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The pr

23、ocedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the edito

24、rial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent right

25、s identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explan

26、ation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso

27、/foreword.html.This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This third edition cancels and replaces the second edition (ISO 28017:2011), of which it constitutes a minor revision. The changes

28、compared to previous edition are as follows: the Amendment ISO 28017:2011/Amd 1:2015 has been incorporated and the normative references have been updated.iv ISO 2018 All rights reservedBS EN ISO 28017:2018Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Speci

29、fication1 ScopeThis document specifies requirements for two types, seven classes and three grades of wire- or textile-reinforced dredging hoses with nominal sizes ranging from 100 to 1 200. Within each class, all grades and sizes have the same maximum working pressure. Such hoses are suitable for th

30、e delivery or suction of seawater or freshwater mixed with silt, sand, coral and small stones with a specific gravity in the range from 1,0 to 2,3 at ambient temperatures ranging from 10 C to +40 C.This document covers two types of hose, as follows: type 1: floating type, for delivery only, which in

31、cludes flotation material to give the hose buoyancy; type 2: submarine type for delivery and suction.This document does not specify requirements concerning the service life of hoses or hose assemblies. Specifying such requirements is the responsibility of the customer, in consultation with the hose

32、manufacturer.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen

33、t (including any amendments) applies.ISO 34-2:2015, Rubber, vulcanized or thermoplastic Determination of tear strength Part 2: Small (Delft) test piecesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1431-1, Rubber, vulcanized or thermoplastic Resistance to ozone crack

34、ing Part 1: Static and dynamic strain testingISO 4649:2010, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum deviceISO 4662:2017, Rubber, vulcanized or thermoplastic Determination of rebound resilienceISO 4671, Rubber and plastics hoses and h

35、ose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assembliesISO 7233:2016, Rubber and plastics hoses and hose assemblies Determination of resistance to vacuumISO 8033, Rubber and plastics hoses Determination of adhesion between componentsISO 8330, Rubber and pl

36、astics hoses and hose assemblies VocabularyISO 10619-1, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8330 apply.INTERNATIONAL

37、STANDARD ISO 28017:2018 ISO 2018 All rights reserved 1BS EN ISO 28017:2018ISO 28017:2018ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at https:/ww

38、w.iso.org/obp4 Classification4.1 ClassesSeven classes of hose are specified, distinguished by their maximum working pressure, of nominal sizes from 100 to 1 200, as shown in Table 1.Table 1 Classes and corresponding maximum working pressures and nominal sizesNominal sizeClass5 10 15 20 25 30 40Maxim

39、um working pressure, MWPbar5 10 15 20 25 30 40MPa0,5 1,0 1,5 2,0 2,5 3,0 4,0100 X X X X X X X150 X X X X X X X200 X X X X X X X250 X X X X X X N/A300 X X X X X X N/A350 X X X X X X N/A400 X X X X X X N/A450 X X X X X X N/A500 X X X X X X N/A550 X X X X X X N/A600 X X X X X X N/A650 X X X X X X N/A70

40、0 X X X X X X N/A750 X X X X X X N/A800 X X X X X X N/A850 X X X X X X N/A900 X X X X X X N/A1 000 X X X X X X N/A1 100 X X X X X X N/A1 200 X X X X X N/A N/AX: ApplicableN/A: Not applicable4.2 GradesType 2 hoses are classified into three grades, A, B and C, according to their construction (number o

41、f reinforcing helical wires), as shown in Table 2.Type 1 hoses are not divided into grades.2 ISO 2018 All rights reservedBS EN ISO 28017:2018ISO 28017:2018Table 2 GradesType GradeConstruction and purposeNumber of reinforcing wiresPurpose1 0 Delivery only2A 2 Delivery or suctionB 1 Delivery or suctio

42、nC 0 Delivery onlyThe types and grades available in each class (i.e. for each maximum working pressure) are as shown in Table 3.Table 3 Types and grades available in each classType GradeClass5 10 15 20 25 30 40Maximum working pressure, MWPbar5 10 15 20 25 30 40MPa0,5 1,0 1,5 2,0 2,5 3,0 4,01 X X X X

43、 X X X2A X X X N/A N/A N/A N/AB X X X N/A N/A N/A N/AC X X X X X X XX: ApplicableN/A: Not applicable5 Materials and construction5.1 Hoses Type 1 hose assemblies shall consist of an abrasion-resistant rubber lining, one or more layers of steel or textile reinforcement, a textile-reinforced rubber und

44、ercover, a flexible closed-cell flotation material integrally fitted round the hose body as described in 5.2, an abrasion- and weather-resistant rubber or thermoplastic outer cover (which, in the case of a rubber cover, can include one or two textile breaker layers), and end fittings as described in

45、 5.3 on both ends.Type 2 hose assemblies shall consist of an abrasion-resistant rubber lining, one or more layers of steel or textile reinforcement, a textile-reinforced rubber, full rubber or thermoplastic cover at least 6 mm thick for hoses of nominal size less than 500, at least 10 mm thick for h

46、oses of nominal size in the range from 500 to 850 inclusive and at least 12 mm thick for hoses of nominal size in the range from 900 to 1 200 inclusive, and end fittings as described in 5.3 on both ends. The lining thickness shall be at least 8 mm for nominal sizes up to and including 200, at least

47、10 mm for nominal sizes 250 to 500 inclusive, at least 12 mm for nominal sizes 550 to 800 inclusive and at least 16 mm for nominal sizes 850 to 1 200 inclusive.5.2 Flotation materialThe closed-cell flotation material used in type 1 hose assemblies shall adhere firmly both to the hose body and to the

48、 outer cover so that it cannot move or tend to become detached in service. At the ends of the hose, a space shall be provided to facilitate the insertion of connection bolts and to allow the use ISO 2018 All rights reserved 3BS EN ISO 28017:2018ISO 28017:2018of mechanical tools for tightening nuts o

49、n the bolts. The flotation material shall be distributed over the whole length of the hose assembly in such a manner that the hose assembly floats evenly when connected to other assemblies in a string. This does not apply to hose assemblies for special applications (e.g. the end of a string, tapered hose, etc.).5.3 End fittings and end connectionsEnd fittings shall be mechanically and chemically bonded to the hose body. With hoses intended for delivery use only, clamped-on and swaged-on nipples are not accep