ETSI EN 300 113-2016 Land Mobile Service Radio equipment intended for the transmission of data (and or speech) using constant or non-constant envelope modulation and having an ante.pdf

1、 ETSI EN 300 113 V2.1.1 (2016-08) Land Mobile Service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 201

2、4/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 113 V2.1.1 (2016-08) 2 Reference REN/ERM-TGDMR-350 Keywords antenna, data, mobile, PMR, radio, regulation, speech, TDD, TDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret

3、N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The

4、content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable

5、Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.ets

6、i.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or m

7、echanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunicat

8、ions Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GS

9、M logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 113 V2.1.1 (2016-08) 3 Contents Intellectual Property Rights 8g3Foreword . 8g3Modal verbs terminology 8g31 Scope 9g32 References 9g32.1 Normative references . 9g32.2 Informative references 10g33 Definitions, symbols

10、 and abbreviations . 11g33.1 Definitions 11g33.2 Symbols 12g33.3 Abbreviations . 12g34 General and operational requirements 13g34.1 General . 13g34.1.1 Environmental profile . 13g34.1.2 Choice of model for testing 13g34.1.2.0 General 13g34.1.2.1 Auxiliary test equipment . 13g34.1.2.2 Declarations by

11、 the manufacturer . 13g34.2 Mechanical and electrical design 14g34.2.1 General 14g34.2.2 Controls 14g34.2.3 Transmitter shut-off facility 14g34.3 Testing using bit streams or messages 14g34.4 Measuring continuous mode equipment . 14g34.5 Measuring discontinuous mode equipment 14g34.6 Constant and no

12、n-constant envelope modulation . 14g34.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 15g35 Test conditions, power sources and ambient temperatures 16g35.1 Normal and extreme test conditions . 16g35.2 Test power source . 16g35.3 Normal test conditions 16g35.3.1 Normal t

13、emperature and humidity 16g35.3.2 Normal test power source . 16g35.3.2.1 Mains voltage 16g35.3.2.2 Regulated lead-acid battery power sources used on vehicles 16g35.3.2.3 Other power sources 17g35.4 Extreme test conditions 17g35.4.1 Extreme temperatures . 17g35.4.2 Extreme test source voltages . 17g3

14、5.4.2.1 Mains voltage 17g35.4.2.2 Regulated lead-acid battery power sources used on vehicles 17g35.4.2.3 Power sources using other types of batteries . 17g35.4.2.4 Other power sources 17g35.5 Procedure for tests at extreme temperatures . 18g35.5.0 Thermal balance 18g35.5.1 Procedure for equipment de

15、signed for continuous transmission. 18g35.5.2 Procedure for equipment designed for intermittent transmission . 18g35.5.3 Testing of equipment that does not have an external 50 RF connector (integral antenna equipment) 18g36 General conditions of measurement . 19g36.1 Arrangements for test signals ap

16、plied to the receiver input 19g36.2 Receiver mute or squelch facility . 19g36.3 Normal test signals (wanted and unwanted signals) . 19g3ETSI ETSI EN 300 113 V2.1.1 (2016-08) 4 6.3.1 Equipment measured as constant envelope angle modulation equipment 19g36.3.2 Equipment measured as non-constant envelo

17、pe modulation equipment . 20g36.4 Encoder for receiver measurements . 20g36.5 Transceiver data interface. 21g36.6 Impedance 21g36.7 Artificial antenna 21g36.8 Tests of equipment with a duplex filter 21g36.9 Facilities for access 21g36.9.1 Analogue access 21g36.9.2 Test points for bit stream measurem

18、ents. 21g36.9.3 Coupling arrangements . 22g36.9.3.0 General 22g36.9.3.1 Arrangements for measurements with continuous bit streams 22g36.9.3.2 Arrangements for measurements with messages . 22g36.10 Test site and general arrangements for measurements involving the use of radiated fields . 22g36.11 Mod

19、es of operation of the transmitter for constant envelope equipment . 22g37 Technical characteristics of the transmitter 23g37.1 Frequency error 23g37.1.0 General 23g37.1.1 Definition 23g37.1.2 Method of measurement . 23g37.1.3 Limits 23g37.2 Transmitter power (conducted) 24g37.2.1 Definitions 24g37.

20、2.1.1 Equipment measured as constant envelope angle modulation equipment . 24g37.2.1.2 Equipment measured as non-constant envelope modulation equipment . 24g37.2.2 Method of measurement . 24g37.2.2.1 Equipment measured as constant envelope angle modulation equipment . 24g37.2.2.2 Equipment measured

21、as non-constant envelope modulation equipment . 25g37.2.3 Limits 25g37.3 Maximum Effective radiated power . 25g37.3.1 Definition 25g37.3.1.0 General 25g37.3.1.1 Equipment measured as constant envelope angle modulation equipment . 25g37.3.1.2 Equipment measured as non-constant envelope modulation equ

22、ipment . 26g37.3.2 Methods of measurement 26g37.3.2.0 General 26g37.3.2.1 Equipment measured as constant envelope angle modulation equipment . 27g37.3.2.2 Equipment measured as non-constant envelope modulation equipment . 28g37.3.3 Limits 29g37.4 Adjacent and alternate channel power 30g37.4.1 Defini

23、tion 30g37.4.2 Method of measurement . 30g37.4.3 Limits 31g37.5 Unwanted emissions in the spurious domain 32g37.5.1 Definition 32g37.5.2 Method of measuring the power level 32g37.5.2.0 General 32g37.5.2.1 Equipment measured as constant envelope angle modulation equipment . 33g37.5.2.2 Equipment meas

24、ured as non-constant envelope modulation equipment . 33g37.5.3 Method of measuring the effective radiated power . 34g37.5.3.0 General 34g37.5.3.1 Equipment measured as constant envelope angle modulation equipment . 34g37.5.3.2 Equipment measured as non-constant envelope modulation equipment . 35g37.

25、5.4 Limits 36g37.6 Intermodulation attenuation 37g37.6.1 Definition 37g37.6.2 Method of measurement . 38g37.6.3 Limits 39g37.7 Transmitter attack time . 39g37.7.1 Definition 39g3ETSI ETSI EN 300 113 V2.1.1 (2016-08) 5 7.7.2 Method of measurement . 39g37.7.3 Limit . 40g37.8 Transmitter release time .

26、 40g37.8.1 Definition 40g37.8.2 Method of measurement . 40g37.8.3 Limits 41g37.9 Transient behaviour of the transmitter 41g37.9.1 Definitions 41g37.9.2 Timings, frequencies and powers . 42g37.9.3 Methods of measurement 46g37.9.3.0 General 46g37.9.3.1 Time domain measurements of power and frequency .

27、 46g37.9.3.2 Test arrangement and characteristics of the FM modulation meter 47g37.9.3.3 Adjacent channel transient power measurements 47g37.9.3.3.1 Definition. 47g37.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 47g37.9.3.3.3 Measurement method for non-constant envel

28、ope modulation equipment . 48g37.9.3.3.4 Alternative measurement method using a spectrum analyser 49g37.9.3.4 Characteristics of the adjacent channel transient power measuring device . 50g37.9.4 Limits 50g37.9.4.0 General 50g37.9.4.1 Time domain analysis of power and frequency for constant envelope

29、transmissions . 51g37.9.4.2 Adjacent and alternate channel transient power 51g37.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 51g37.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 51g38 Technical characteristics of the receiver 52g38.1 Maxim

30、um usable sensitivity (conducted) . 52g38.1.1 Definition 52g38.1.2 Method of measurement . 52g38.1.2.1 Method of measurement with continuous bit streams . 52g38.1.2.2 Method of measurement with messages 53g38.1.2.3 Method of measurement with packets . 53g38.1.3 Limits 54g38.2 Average usable sensitiv

31、ity (field strength) . 54g38.2.1 Definition 54g38.2.2 Method of measurement . 54g38.2.3 Limits 55g38.3 Level of the wanted signal for the degradation measurements . 55g38.4 Error behaviour at high input levels . 56g38.4.1 Definition 56g38.4.2 Method of measurement . 56g38.4.2.1 Method of measurement

32、 with continuous bit streams . 56g38.4.2.2 Method of measurement with messages 56g38.4.2.3 Method of measurement with packets . 57g38.4.3 Limits 57g38.5 Co-channel rejection. 57g38.5.1 Definition 57g38.5.2 Method of measurement . 58g38.5.2.1 Method of measurement with continuous bit streams . 58g38.

33、5.2.2 Method of measurement with messages 59g38.5.2.3 Method of measurement with packets . 60g38.5.3 Limits 60g38.6 Adjacent channel selectivity . 61g38.6.1 Definition 61g38.6.2 Method of measurement . 61g38.6.2.1 Method of measurement with continuous bit streams . 61g38.6.2.2 Method of measurement

34、with messages 62g38.6.2.3 Method of measurement with packets . 63g38.6.3 Limits 64g38.7 Spurious response rejection 64g38.7.1 Definition 64g3ETSI ETSI EN 300 113 V2.1.1 (2016-08) 6 8.7.2 Introduction to the method of measurement . 64g38.7.3 Method of search over the “limited frequency range“ 65g38.7

35、.4 Method of measurement with continuous bit streams . 66g38.7.5 Method of measurement with messages . 66g38.7.6 Method of measurement with packets 67g38.7.7 Limits 68g38.8 Intermodulation response rejection 68g38.8.1 Definition 68g38.8.2 Method of measurement . 69g38.8.2.1 Method of measurement wit

36、h continuous bit streams . 69g38.8.2.2 Method of measurement with messages 70g38.8.2.3 Method of measurement with packets . 71g38.8.3 Limits 71g38.9 Blocking or desensitization 72g38.9.1 Definition 72g38.9.2 Method of measurement . 72g38.9.2.1 Method of measurement with continuous bit streams . 72g3

37、8.9.2.2 Method of measurement with messages 73g38.9.2.3 Method of measurement with packets . 74g38.9.3 Limits 74g38.10 Spurious radiations . 74g38.10.1 Definition 74g38.10.2 Method of measuring the power level 75g38.10.3 Method of measuring the effective radiated power . 76g38.10.4 Limits 77g39 Dupl

38、ex operation 78g39.1 Receiver desensitization (with simultaneous transmission and reception) . 78g39.1.1 Definition 78g39.1.2 Desensitization measured with continuous bit streams . 79g39.1.2.1 Method of measurement when the equipment has a duplex filter . 79g39.1.2.2 Method of measurement when the e

39、quipment has to operate with two antennas 80g39.1.3 Limits 81g39.2 Receiver spurious response rejection (with simultaneous transmission and reception) . 81g39.2.1 Definition 81g39.2.2 Method of measurement . 81g39.2.3 Limits 83g310 Testing for compliance with technical requirements 83g310.1 Test con

40、ditions, power supply and ambient temperatures 83g310.2 Interpretation of the measurement results 83g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 85g3Annex B (normative): Radiated measurement 87g3B.1 Test sites and general a

41、rrangements for measurements involving the use of radiated fields . 87g3B.1.0 General . 87g3B.1.1 Anechoic chamber 87g3B.1.2 Anechoic chamber with a conductive ground plane . 88g3B.1.3 Open Area Test Site (OATS) . 89g3B.1.4 Test antenna 90g3B.1.5 Substitution antenna . 90g3B.1.6 Measuring antenna .

42、91g3B.2 Guidance on the use of radiation test sites . 91g3B.2.0 General . 91g3B.2.1 Verification of the test site . 91g3B.2.2 Preparation of the EUT . 91g3B.2.3 Power supplies to the EUT . 91g3B.2.4 Volume control setting for analogue speech tests 91g3B.2.5 Range length . 92g3ETSI ETSI EN 300 113 V2

43、.1.1 (2016-08) 7 B.2.6 Site preparation 92g3B.3 Coupling of signals . 93g3B.3.0 General . 93g3B.3.1 Data signals 93g3B.3.2 Speech and analogue signals 93g3B.3.2.0 General 93g3B.3.2.1 Acoustic coupler description. 93g3B.3.2.2 Calibration 94g3Annex C (normative): Specification for some particular meas

44、urement arrangements . 95g3C.1 Power measuring receiver specification . 95g3C.1.0 General . 95g3C.1.1 IF filter . 95g3C.1.2 Attenuation indicator 96g3C.1.3 RMS value indicator . 96g3C.1.4 Oscillator and amplifier 96g3C.2 Spectrum analyser specification . 97g3C.2.1 Adjacent and alternate channel powe

45、r measurement 97g3C.2.2 Unwanted emissions measurement . 97g3C.3 Integrating and power summing device . 97g3Annex D (informative): Change History 98g3History 99g3ETSI ETSI EN 300 113 V2.1.1 (2016-08) 8 Intellectual Property Rights IPRs essential or potentially essential to the present document may h

46、ave been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI stan

47、dards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not r

48、eferenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). T

49、he present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.3 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits