ETSI EN 300 220-3-2-2017 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 3-2 Harmonised Standard covering the essential requirements of article .pdf

1、 ETSI EN 300 220-3-2 V1.1.1 (2017-02) Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 3-2: Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Wireless alarms operating in designated LDC/HR frequency bands 868,60 MHz to

2、 868,70 MHz, 869,25 MHz to 869,40 MHz, 869,65 MHz to 869,70 MHz HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)2 Reference DEN/ERM-TG28-528 Keywords harmonised standard, radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 4

3、2 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electro

4、nic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing docu

5、ment is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents

6、 is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any for

7、m or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in

8、all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organ

9、izational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g3

10、2.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 8g33.3 Abbreviations . 8g34 Technical requirements specifications . 8g34.1 Environmental profile . 8g34.2 All equipment conformance requirements . 9g34.2.0 Compliance . 9g34.2.1 Operating frequ

11、ency . 9g34.2.1.0 Applicability 9g34.2.1.1 Description 9g34.2.1.2 Limits 9g34.2.1.3 Conformance . 9g34.2.2 Unwanted emissions in the spurious domain 9g34.2.2.0 Applicability 9g34.2.2.1 Description 9g34.2.2.2 Limits 9g34.2.2.3 Conformance . 9g34.3 Transmitters conformance requirements 9g34.3.1 Effect

12、ive Radiated Power . 9g34.3.1.0 Applicability 9g34.3.1.1 Description 10g34.3.1.2 Limits 10g34.3.1.3 Conformance . 10g34.3.2 Duty Cycle 10g34.3.2.0 Applicability 10g34.3.2.1 Description 10g34.3.2.2 Limits 10g34.3.2.3 Conformance . 10g34.3.3 Maximum Occupied Bandwidth . 10g34.3.3.0 Applicability 10g34

13、.3.3.1 Description 10g34.3.3.2 Limits 10g34.3.3.3 Conformance . 10g34.3.4 TX Out Of Band Emissions 11g34.3.4.0 Applicability 11g34.3.4.1 Description 11g34.3.4.2 Limits 11g34.3.4.3 Conformance . 11g34.3.5 Transient power 11g34.3.5.0 Applicability 11g34.3.5.1 Description 11g34.3.5.2 Limits 11g34.3.5.3

14、 Conformance . 11g34.3.6 Adjacent Channel Power 11g34.3.6.0 Applicability 11g3ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)4 4.3.6.1 Description 11g34.3.6.2 Limits 11g34.3.6.3 Conformance . 12g34.3.7 TX behaviour under Low Voltage Conditions 12g34.3.7.0 Applicability 12g34.3.7.1 Description 12g34.3.7.2

15、Limits 12g34.3.7.3 Conformance . 12g34.4 Receivers conformance requirements . 12g34.4.1 Blocking 12g34.4.1.0 Applicability 12g34.4.1.1 Description 12g34.4.1.2 Limits 12g34.4.1.3 Conformance . 12g3Annex A (informative): Relationship between the present document and the essential requirements of Direc

16、tive 2014/53/EU . 13g3Annex B (normative): EU LDC/HR designated frequency bands for wireless alarm equipment . 14g3Annex C (informative): Application form for testing 15g3C.1 Description . 15g3C.2 Information as required by ETSI EN 300 220-3-2 . 15g3Annex D (informative): Selection of technical para

17、meters . 17g3D.1 Introduction 17g3D.2 Receiver sensitivity 17g3D.3 Other receiver parameters 17g3Annex E (informative): Change History 18g3History 19g3ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been

18、 declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“,

19、which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not reference

20、d in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The prese

21、nt document has been prepared under the Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market o

22、f radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present docu

23、ment, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 3-2 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. For non EU countries the present document may

24、be used for regulatory (Type Approval) purposes. National transposition dates Date of adoption of this EN: 27 January 2017 Date of latest announcement of this EN (doa): 30 April 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 October 2017 Date of withdr

25、awal of any conflicting National Standard (dow): 31 October 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal

26、 forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)6 Introduction The present document is part 3-2 of a multi-part deliverable covering wireless alarm Short Range Devices (

27、SRD) operating in the designated LDC/HR frequency range 868,60 MHz to 868,70 MHz, 869,25 MHz to 869,40 MHz, 869,65 MHz to 869,70 MHz. The present document is structured as follows: Clause 2 provides references. Clause 3 provides definitions of terms and abbreviations used. Clause 4 provides technica

28、l requirements. Annex A (informative): provides relationship between the present document and essential requirements of Directive 2014/53/EU i.1. Annex B (normative): EU designated frequency bands for wireless alarm equipment. Annex C (informative): Application form for testing. Annex D (informative

29、): Selection of parameters. Annex E (informative): Change History. ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)7 1 Scope The present document specifies technical characteristics and methods of measurements for LDC/HR wireless alarm equipment types: LDC/HR category is defined by the EU Commission Decisi

30、on 2013/752/EU i.2 as: “The low duty cycle/high reliability device category covers radio devices that rely on low overall spectrum utilisation and low duty cycle spectrum access rules to ensure highly reliable spectrum access and transmissions in shared bands. Typical uses include alarm systems that

31、 use radio“. The present document covers equipment intended for fixed, mobile or nomadic use, e.g.: stand-alone radio equipment; plug-in radio devices intended for use with or within a variety of host systems; plug-in radio devices intended for use within combined equipment. These radio equipment ty

32、pes are capable of operating in the LDC/HR designated frequency bands given in table 1. Table 1: Wireless alarm LDC/HR designated frequency bands Frequency band Transmit and Receive 868,600 to 868,700 MHz Transmit and Receive 869,250 to 869,400 MHz Transmit and Receive 869,650 to 869,700 MHz The pre

33、sent document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.1 under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version appl

34、ies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following

35、 referenced documents are necessary for the application of the present document. 1 ETSI EN 300 220-1 (V3.1.1) (02-2017): “Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement“. 2.2 Informative references Referenc

36、es are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any

37、hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)8 The following referenced documents are not necessary for the application of the present document but they assist the user with regard t

38、o a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Commission Decision 2013

39、/752/EU on harmonisation of the radio spectrum for use by short-range devices as amended by subsequent Commission Decisions. i.3 ETSI EG 203 336: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standard

40、s covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.4 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards ra

41、dio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.5 Commission Decision 2000/299/EU on harmonisation of the radio spectrum for use by short-range devices as amended by subsequent Commission Decisions. 3 Definitions, symbols and abbreviations 3.1 Defini

42、tions For the purposes of the present document, the terms and definitions given in the RE-Directive i.1 and ETSI EN 300 220-1 1 apply. 3.2 Symbols For the purposes of the present document, the symbols given in ETSI EN 300 220-1 1 apply. 3.3 Abbreviations For the purposes of the present document, the

43、 abbreviations given in ETSI EN 300 220-1 1 apply. 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment sha

44、ll comply with all the technical requirements of the present document which are identified as applicable in annex A at all times when operating within the boundary limits of the declared operational environmental profile. Normal and extreme tests conditions are defined in ETSI EN 300 220-1 1, clause

45、s 4.3.3 and 4.3.4. ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)9 4.2 All equipment conformance requirements 4.2.0 Compliance When an operational frequency band is selected from table B.1 from annex B for the equipment under test, the equipment shall comply with all parameters, exclusions and notes from

46、 the row in table B.1 unless a different National Radio Interface applies. 4.2.1 Operating frequency 4.2.1.0 Applicability Clause 4.2.1 applies to all equipment. 4.2.1.1 Description For the purpose of the present document, the description in ETSI EN 300 220-1 1, clause 5.1.1 applies. 4.2.1.2 Limits

47、The manufacturer may declare either one or more operating frequencies and operating channels. Operating channel(s) shall be entirely within operational frequency bands allowed by annex B. 4.2.1.3 Conformance The conformance for this requirement shall be as defined in ETSI EN 300 220-1 1, clause 5.1.

48、2. 4.2.2 Unwanted emissions in the spurious domain 4.2.2.0 Applicability Clause 4.2.2 applies to all equipment. 4.2.2.1 Description For the purpose of the present document, the description in ETSI EN 300 220-1 1, clauses 5.9.1.1 and 5.9.1.2 apply. 4.2.2.2 Limits The EUT shall comply with reference l

49、imits defined in ETSI EN 300 220-1 1, clause 5.9.2. 4.2.2.3 Conformance The conformance tests for this requirement shall be as defined in ETSI EN 300 220-1 1, clause 5.9.3. Conformance shall be established under normal test conditions. 4.3 Transmitters conformance requirements 4.3.1 Effective Radiated Power 4.3.1.0 Applicability Clause 4.3.1 applies to all transmitters. ETSI ETSI EN 300 220-3-2 V1.1.1 (2017-02)10 4.3.1.1 Description For the purpose of the document, the description in ETSI EN 300 220-1 1, clause 5.2.1 appl