ETSI EN 300 338-4-2017 Technical characteristics and methods of measurement for equipment for generation transmission and reception of Digital Selective Calling (DSC) in the mariti.pdf

1、 ETSI EN 300 338-4 V1.2.1 (2017-02) Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 4: Class E DSC EUROPEAN STANDARD ETSI ETSI EN 300 338-4 V1.2.

2、1 (2017-02) 2 Reference REN/ERM-TG26-087-4 Keywords DSC, GMDSS, maritime, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse

3、 (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified witho

4、ut the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of th

5、e present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your co

6、mment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI.

7、 The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo ar

8、e Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 338-4 V1.2.1 (

9、2017-02) 3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitions and abbreviations . 8g33.1 Definitions 8g33.2 Abbreviations . 9g34 Controls and Indicators in Class E DSC

10、Equipment 10g34.1 Visual indication 10g34.1.0 General 10g34.1.1 DSC alphanumeric display . 10g34.1.1.0 Primary display information 10g34.1.1.1 Additional display information . 10g34.1.2 Display requirements for additional controllers 10g34.1.3 Handling visual information . 11g35 Technical requiremen

11、ts 11g35.1 Facilities for DSC transmission and reception . 11g35.1.1 Watch receiver capabilities . 11g35.2 Facilities for coding and decoding of DSC 11g35.2.1 Call functions 11g35.2.2 INDIVIDUAL calls 11g35.2.3 GEOGRAPHIC area calls . 12g35.2.4 DSC call functionality 12g36 Automated and Non-Automate

12、d Procedure Requirements in Class E DSC Equipment 13g36.1 Introduction 13g36.2 Non-automated features . 13g36.2.0 Introduction. 13g36.2.1 DSC Message Composition 13g36.2.2 Transmission of DSC messages and prioritized wait 14g36.2.3 Alarms 14g36.3 Standby . 15g36.4 Sending distress automated procedur

13、e (need to be revised to HF multifrequency alert attempts) . 16g36.4.1 Procedure 16g36.4.2 Tasks . 18g36.4.3 Display 18g36.4.4 Dedicated distress button sub procedure . 19g36.4.5 Transmission of the alert attempt 20g36.4.6 Updating position 20g36.4.7 Handling received DSC Messages 20g36.4.8 Alarms 2

14、0g36.4.9 Determining Subsequent communications 20g36.4.10 Automated tuning . 20g36.4.11 Cancelling the Distress Alert 21g36.4.12 Acknowledgments 21g36.4.13 Termination. 21g36.4.14 Warnings . 21g36.5 Receiving distress automated procedure 22g36.5.1 Procedure 22g36.5.2 Tasks . 23g36.5.3 Display 23g3ET

15、SI ETSI EN 300 338-4 V1.2.1 (2017-02) 4 6.5.4 Handling received DSC Messages 24g36.5.5 Alarms 24g36.5.6 Determining Subsequent communications 24g36.5.7 Automated tuning . 24g36.5.8 Acknowledgments 24g36.5.9 Termination. 25g36.5.10 Warnings . 25g36.6 Sending non distress automated procedure 25g36.6.1

16、 Procedure 25g36.6.2 Tasks . 26g36.6.3 Display 26g36.6.4 Handling received DSC Messages 27g36.6.5 Alarms 27g36.6.6 Automated tuning . 27g36.6.7 Delayed Acknowledgements 28g36.6.8 Termination. 28g36.6.9 Warnings . 28g36.7 Receiving non distress automated procedure . 28g36.7.1 Procedure 28g36.7.2 Task

17、s . 29g36.7.3 Display 30g36.7.4 Handling received DSC messages 31g36.7.5 Alarms 31g36.7.6 Automated tuning . 31g36.7.7 Acknowledgments 31g36.7.8 Termination. 32g36.7.9 Warnings . 32g36.8 Communications automated procedure 32g36.8.1 Procedure 32g36.8.2 Tasks . 32g36.8.3 Display 33g36.8.4 Handling rec

18、eived DSC Messages 33g36.8.5 Tuning of the general receiver and transmitter . 33g36.8.6 Termination. 33g36.9 Handling incoming calls while the equipment is engaged . 33g36.9.1 Procedure 33g36.9.2 Tasks . 33g36.9.2.0 Introduction . 33g36.9.2.1 Higher priority calls 33g36.9.2.1.0 Priority . 33g36.9.2.

19、1.1 Higher priority calls - acceptance 34g36.9.2.1.2 Higher priority calls - non acceptance . 34g36.9.2.2 Other calls . 34g36.9.2.3 Termination of automated procedures . 35g36.9.2.4 Action after termination of an automated procedure . 35g36.9.2.5 Putting automated procedures on hold (optional) . 35g

20、36.9.2.6 Controlling non-terminated automated procedures (optional) 35g3Annex A (normative): DSC Message Composition . 37g3A.1 Default values . 37g3Annex B (normative): Radius-centre point conversion and rounding algorithm 38g3B.1 Radius-centre point conversion 38g3B.2 Rounding 39g3B.3 Special cases

21、 for either form of area data entry . 39g3Annex C (normative): Automated non distress channel selection algorithm . 40g3Annex D (normative): Alarms . 41g3ETSI ETSI EN 300 338-4 V1.2.1 (2017-02) 5 D.1 Alarm specifications . 41g3D.2 Alarming with critical errors 42g3D.3 Default alarm sounds 42g3D.4 Ot

22、her alarm sounds . 43g3History 44g3ETSI ETSI EN 300 338-4 V1.2.1 (2017-02) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members

23、 and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.or

24、g/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the pr

25、esent document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.2. The present doc

26、ument covers the operator interfaces and operating system for Class E DSC equipment. National transposition dates Date of adoption of this EN: 8 February 2017 Date of latest announcement of this EN (doa): 31 May 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/

27、e): 30 November 2017 Date of withdrawal of any conflicting National Standard (dow): 30 November 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.

28、2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 338-4 V1.2.1 (2017-02) 7 1 Scope The present document states the minimum requirements for general communicati

29、on for shipborne fixed installations using DSC - class E. Class E DSC is intended to be used in the Medium Frequency (MF) and/or High Frequency (HF) bands of the Maritime Mobile Service (MMS), for distress, urgency and safety communication and general communications and uses telephony for subsequent

30、 communications. The present document is part 4 of a multi-part deliverable that covers the requirements to be fulfilled by equipment that is either integrated with a transmitter and/or a receiver or equipment that is a stand-alone DSC terminal. These requirements include the relevant provisions and

31、 the guidelines of the IMO as detailed in MSC/Circ.803 i.1 for non-SOLAS vessels participating in the GMDSS as well as Commission Decision of 4 September 2003 (2004/71/EC i.3). 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition numb

32、er or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location mi

33、ght be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ITU Radio Regulat

34、ions (2016). 2 Recommendation ITU-R M.493-14 (09/2015): “Digital selective-calling system for use in the maritime mobile service“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific refer

35、ences, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The followin

36、g referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 IMO Circular MSC/Circ-803: “Participation of non-SOLAS ships in the Global Maritime Distress and Safety System (GMDSS)“. i.2 ETSI EN 300 338-1:

37、“Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 1: Common requirements“. i.3 Commission Decision 2004/71/EC of 4 September 2003 on essential req

38、uirements relating to marine radio communication equipment which is intended to be used on non-SOLAS vessels and to participate in the Global Maritime Distress and Safety System (GMDSS). ETSI ETSI EN 300 338-4 V1.2.1 (2017-02) 8 i.4 Maritime Safety Committee MSC 302(87): “Adoption of performance sta

39、ndards for bridge alert management“. i.5 IEC 61924-2 Edition 1 (including IEC 61924-2 Corrigendum 1 November 2013): “Maritime navigation and radiocommunication equipment and systems - integrated navigation systems - Part 2: Modular structure for INS - operational and performance requirements, method

40、s of testing and required test results“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 300 338-1 i.2 and the following apply: acknowledged: automated procedure that indicates the objective of the initial DSC messa

41、ge has been achieved active: automated procedure which has control of the general receiver and transmitter and is thus able to engage in subsequent communications and receive DSC messages on both the watch receiver and general receiver automated procedure: set of actions necessary to complete the ob

42、jective of an initiating DSC message or non DSC communication event NOTE 1: Four DSC automated procedures are designed to process these. They are the receiving of distress DSC messages, the receiving of non distress DSC messages, the sending of distress DSC alert attempts and the sending of non dist

43、ress DSC messages. In addition a fifth procedure is designed to handle non DSC communication events. NOTE 2: These automated procedures are called: - Received distress automated procedure. - Sending distress automated procedure. - Received non-distress automated procedure. - Sending non-distress aut

44、omated procedure. - Communications automated procedure. block: inhibit a function by making it inaccessible from the user interface class E: DSC class intended to provide minimum facilities for MF/HF DSC distress, urgency and safety as well as routine calling and reception, not necessarily in full a

45、ccordance with IMO GMDSS carriage requirements for MF installations default: value selected or an action taken by the equipment software in the absence of any operator input distress DSC message: DSC message or acknowledgement containing the distress information distress event: unique distress situa

46、tion identified by two parameters of the distress information; the MMSI of the vessel in distress and the nature of distress engaged: equipment that is busy handling an automated procedure factory default: default value that is set by the manufacturer such that the field or behaviour is defined prio

47、r to any operator intervention general receiver: transceiver used for the reception of all subsequent communications NOTE: It is important to distinguish this unit from the watch receiver. ETSI ETSI EN 300 338-4 V1.2.1 (2017-02) 9 information characters: set of symbols in a DSC message that contains

48、 the items of interest for the recipient and is used to compute the ECC symbol that terminates the message NOTE: These symbols are repeated in the DX/RX time diversity pattern. initial DSC message: DSC message that starts an automated procedure non distress DSC message: DSC messages or acknowledgmen

49、ts that do not have the format specifier or category of “distress“ objective: intent of the DSC message either to establish subsequent communications or request information operator options: any choices the operator can make while the automated procedure is engaged pertinent to the automated procedure: DSC messages that have something to do with the procedure and are therefore handled by the procedure NOTE: A DSC message is pertinent to an automated procedure if the set of information characters in the DSC message has the correct values. pertinent to t