ETSI EN 300 341-2016 Land Mobile Service Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver Harmonised Standard covering.pdf

1、 ETSI EN 300 341 V2.1.1 (2016-03) Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI

2、ETSI EN 300 341 V2.1.1 (2016-03) 2 Reference REN/ERM-TGDMR-352 Keywords analogue, mobile, PMR, radio, signalling ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enreg

3、istre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present doc

4、ument shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive wit

5、hin ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the pres

6、ent document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authoriz

7、ed by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTE

8、STSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association

9、. ETSI ETSI EN 300 341 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 8g33.3 Abbre

10、viations . 9g34 Speech equipment with signalling 9g35 General and operational requirements 10g35.1 General . 10g35.1.1 Environmental profile . 10g35.1.2 Choice of model for testing 10g36 Test conditions, power sources and ambient temperatures 10g36.1 Normal and extreme test conditions . 10g36.2 Test

11、 power source . 10g36.3 Normal test conditions 11g36.3.1 Normal temperature and humidity 11g36.3.2 Normal test power source 11g36.3.2.1 Mains voltage 11g36.3.2.2 Regulated lead-acid battery power sources used on vehicles 11g36.3.2.3 Other power sources 11g36.4 Extreme test conditions . 11g36.4.1 Ext

12、reme temperatures 11g36.4.2 Extreme test source voltages . 12g36.4.2.1 Mains voltage 12g36.4.2.2 Regulated lead-acid battery power sources used on vehicles 12g36.4.2.3 Power sources using other types of batteries . 12g36.4.2.4 Other power sources 12g36.5 Procedure for tests at extreme temperatures .

13、 12g36.5.0 Thermal Balance 12g36.5.1 Procedure for equipment designed for continuous operation 12g36.5.2 Procedure for equipment designed for intermittent operation 12g37 General conditions of measurement . 13g37.1 Normal test signals, test conditions and the unwanted test signals. 13g37.2 Artificia

14、l antenna . 13g37.3 Test sites and general arrangements for radiated measurements 13g37.4 Transmitter automatic shut-off facility . 13g37.5 Modes of operation of the transmitter 13g37.6 Arrangements for test signals at the input of the receiver via a test fixture or a test antenna . 14g37.7 Receiver

15、 mute or squelch facility . 14g37.8 Encoder for receiver measurements . 14g37.9 Facilities for access between the receiver demodulator output and its decoder . 14g37.10 Calling indicator 14g37.11 Reset . 14g37.12 Reset time . 14g38 Technical characteristics of the transmitter 15g38.1 Frequency error

16、 15g38.1.0 Applicability . 15g38.1.1 Definition 15g3ETSI ETSI EN 300 341 V2.1.1 (2016-03) 4 8.1.2 Method of measurement . 15g38.1.3 Limits 15g38.2 Effective radiated power . 16g38.2.0 Applicability . 16g38.2.1 Definition 16g38.2.2 Method of measurement 16g38.2.2.1 Maximum effective radiated power un

17、der normal test conditions 16g38.2.2.2 Average effective radiated power under normal test conditions . 18g38.2.3 Method of measurements of maximum and average effective radiated power under extreme test conditions 19g38.2.4 Limits 19g38.3 Adjacent and alternate channel power 20g38.3.0 Applicability

18、. 20g38.3.1 Definition 20g38.3.2 Method of measurement 20g38.3.3 Limits 21g38.4 Radiated spurious emissions 21g38.4.0 Applicability . 21g38.4.1 Definition 22g38.4.2 Method of measurement 22g38.4.3 Limits 24g38.5 Transient frequency behaviour of the transmitter . 24g38.5.0 Applicability . 24g38.5.1 D

19、efinitions 24g38.5.2 Method of measurement 25g38.5.3 Limits 28g39 Technical characteristics of the receiver 28g39.1 Average usable sensitivity (field strength, responses) 28g39.1.0 Applicability . 28g39.1.1 Definition 28g39.1.2 Method of measurement under normal test conditions . 28g39.1.3 Method of

20、 measurement of the average usable sensitivities under extreme test conditions . 30g39.1.4 References for degradation measurements . 30g39.1.4.1 Definition . 30g39.1.4.2 Procedures for measurements using the test fixture 31g39.1.4.3 Procedures for measurements using the test site . 31g39.1.5 Limits

21、31g39.2 Co-channel rejection . 32g39.2.0 Applicability . 32g39.2.1 Definition 32g39.2.2 Method of measurement 32g39.2.3 Limits 33g39.3 Adjacent channel selectivity 34g39.3.0 Applicability . 34g39.3.1 Definition 34g39.3.2 Method of measurement 34g39.3.3 Limits 35g39.4 Spurious response rejection . 35

22、g39.4.0 Applicability . 35g39.4.1 Definition 36g39.4.2 Introduction to the method of measurement . 36g39.4.3 Measurement arrangement . 37g39.4.4 Method of the search . 38g39.4.5 Method of measurement 38g39.4.6 Limits 39g39.5 Intermodulation response rejection 39g39.5.0 Applicability . 39g39.5.1 Defi

23、nition 39g39.5.2 Method of measurement 40g39.5.3 Limits 41g39.6 Blocking or desensitization . 41g3ETSI ETSI EN 300 341 V2.1.1 (2016-03) 5 9.6.0 Applicability . 41g39.6.1 Definition 41g39.6.2 Method of measurement 42g39.6.3 Limits 43g39.7 Receiver Spurious radiations . 43g39.7.0 Applicability . 43g39

24、.7.1 Definition 43g39.7.2 Method of measurement 44g39.7.3 Limits 45g310 Testing for compliance with technical requirements 45g310.1 Test conditions, power supply and ambient temperatures 45g310.2 Interpretation of the measurement results 46g3Annex A (normative): Radiated measurement 47g3A.1 Test sit

25、es and general arrangements for measurements involving the use of radiated fields . 47g3A.1.0 General . 47g3A.1.1 Anechoic chamber 47g3A.1.2 Anechoic chamber with a conductive ground plane . 48g3A.1.3 Open Area Test Site (OATS) . 49g3A.1.4 Test antenna 50g3A.1.5 Substitution antenna . 50g3A.1.6 Meas

26、uring antenna . 51g3A.2 Guidance on the use of radiation test sites . 51g3A.2.0 General . 51g3A.2.1 Verification of the test site . 51g3A.2.2 Preparation of the EUT . 51g3A.2.3 Power supplies to the EUT . 51g3A.2.4 Volume control setting for analogue speech tests 51g3A.2.5 Range length . 52g3A.2.6 S

27、ite preparation 52g3A.3 Coupling of signals . 53g3A.3.1 General . 53g3A.3.2 Data signals 53g3A.3.3 Speech and analogue signals 53g3A.3.3.0 General 53g3A.3.3.1 Acoustic coupler description. 53g3A.3.3.2 Calibration 53g3A.4 Test fixture . 54g3A.4.1 Description . 54g3A.4.2 Calibration 54g3A.4.3 Mode of

28、use 55g3Annex B (normative): Specification for some particular measurement arrangements . 56g3B.1 Power measuring receiver specification . 56g3B.1.0 General . 56g3B.1.1 IF filter . 56g3B.1.2 Attenuation indicator 58g3B.1.3 RMS value indicator . 58g3B.1.4 Oscillator and amplifier 58g3B.2 Spectrum ana

29、lyser specification . 58g3B.2.1 Adjacent and alternate channel power measurement 58g3B.2.2 Unwanted emissions measurement . 59g3B.3 Integrating and power summing device . 59g3Annex C (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 60g3H

30、istory 62g3ETSI ETSI EN 300 341 V2.1.1 (2016-03) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can

31、be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI

32、IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword T

33、his Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.6 to provide one voluntary means of conforming

34、 to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.5. Once the present document is cited in the Official Journal of the European Union under

35、 that Directive, compliance with the normative clauses of the present document given in table C.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. National tr

36、ansposition dates Date of adoption of this EN: 21 March 2016 Date of latest announcement of this EN (doa): 30 June 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 December 2016 Date of withdrawal of any conflicting National Standard (dow): 31 December 2

37、017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must no

38、t“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 341 V2.1.1 (2016-03) 7 1 Scope The present document applies to constant envelope angle modulation systems for use in the land mobile service, using the available bandwidth, operating on radio frequencies be

39、tween 30 MHz and 1 GHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz intended for transmission and/or reception of signals used to initiate a specific response in the receiver. Table 1: Radiocommunications service frequency bands Radiocommunications service frequency bands Transmit 30 MHz

40、 to 1 000 MHz Receive 30 MHz to 1 000 MHz The present document applies to non-speech and to the non-speech part of combined speech/non-speech analogue equipment. In the present document, non-speech radio equipment is defined as a radio equipment transmitting a signal to initiate a specific response

41、in the receiver. The equipment comprises a transmitter and associated encoder and/or a receiver and associated decoder. The encoder and/or decoder may be a separate piece of equipment, in which case compliance to the present document covers the encoder and/or decoder in connection with the transmitt

42、er and/or receiver equipment. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The type of equipment covered by the present document is handportable stations with

43、 integral antennas. The present document contains requirements to demonstrate that “. Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“ and that “radio equipment supports certain features ens

44、uring access to emergency services“ i.5. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive i.5 may apply to equipment within the scope of the present document. 2 Refe

45、rences 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including a

46、ny amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validi

47、ty. The following referenced documents are necessary for the application of the present document. 1 ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 2 ANSI C63

48、.5 (2006): “American National Standard for Electromagnetic Compatibility - Radiated Emission Measurements in Electromagnetic Interference (EMI) Control - Calibration of Antennas (9 kHz to 40 GHz)“. 3 ETSI EN 300 296 (V2.1.1) (03-2016): “Land Mobile Service; Radio equipment using integral antennas in

49、tended primarily for analogue speech; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. ETSI ETSI EN 300 341 V2.1.1 (2016-03) 8 4 ETSI TR 100 028-2 (V1.4.1) (12-2001): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited versi