ETSI EN 300 390-2-2000 Electronic Compatibility and Radio Spectrum Matters (ERM) Land Mobile Service Radio Equipment Intended for the Transmission of Data (and Speech) and Using an.pdf

1、ETSI EN 300 390-2 1.1.1 (2000-09) Candida te Harmonized European Standard (Telecomm unica tions series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna; Part 2: Harmo

2、nized EN covering essential requirements under article 3.2 of the R Essential, or potentially Essential, IPRs notifed to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (-). Pursuant to the ETSI IPR Policy, no inve

3、stigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmo

4、nized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 2 of a multi-part EN covering the Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile

5、 Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna, as identified below: Part 1: Part 2: “Technical characteristics and test conditions“; “Harmonized EN covering essential requirements under article 3.2 of the R 3.2 Spectrum I Use of spectrum I

6、 inrir7 New radio harrnonised standards 11 Scoped by frequency and/or equipment type iL I uuuu I I 3m1 EMC b Radio Product EMC Existing EMC standards to be replaced by a new, single, multi-part standard 1 I I IGeneric and product standards also notified under EMC Directive I Figure 1 : Modular struc

7、ture for the various standards used under the R it provides scope for standards to be added: - - - under article 3.2 when new frequency bands are agreed or under article 3.3 should the Commission take the necessary decisions without requiring alteration of standards that are already published; it cl

8、arifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. - ETSI 8 ETSI EN 300 390-2 V1.l.l (2000-09) 1 Scope The present document covers the minimum characteristics considered necessary in order to make the best use of the available frequenci

9、es. It does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. The present document applies to constant envelope angle modulation systems for use in the land mobile service, using the available bandwi

10、dth, operating on radio frequencies between 30 MHz and 1 O00 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz intended for data transmissions. It applies to digital and combined analogue and digital radio equipment which is hand portable, using an integral antenna and intended for the tr

11、ansmission of data and/or speech. The technical characteristics given in this present document are independent of data rate but may in practice limit the maximum data rate achievable. Future editions of this present document may be prepared which may allow complex modulation methods, together with t

12、heir appropriate limits, for use at higher bit rates. In this present document, a digital radio equipment is defined as a radio equipment which transmits and/or receives data. Data equipment is understood as equipment handling continuous bit streams or messages. The equipment comprises a transmitter

13、 and associated encoder and modulator and/or a receiver and associated demodulator and decoder. The encoder and/or decoder may be a separate piece of equipment, in which case this present document covers the combination of encoder and/or decoder and transmitter and/or receiver equipment. The present

14、 document is intended to cover the provisions of Article 3.2, of Directive 1999/5/EC i (R Technical characteristics and test conditions “. Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technic

15、al standards and regulations. 51 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R it shows the status of each EN-R, whether it is essential to implement in all circumstances (Mandatory), or whether the require

16、ment is dependent on the supplier having chosen to support a particular optional service or functionality (Optional). In particular it enables the EN-Rs associated with a particular optional service or functionality to be grouped and identified; when completed in respect of a particular equipment it

17、 provides a means to undertake the static assessment of conformity with the EN. - Table A.l: EN Requirements Table (EN-RT) Key to columns: No Reference EN-R Status M O 0.n Comments Table entry number; Subclause reference number of conformance requirement within the present document; Title of conform

18、ance requirement within the present document; Status of the entry as follows: Mandatory, shall be implemented under all circumstances; Optional, may be provided, but if provided shall be implemented in accordance with the requirements; this status is used for mutually exclusive or selectable options

19、 among a set. The integer “n“ shall refer to a unique group of options within the EN-RT. A footnote to the EN-RT shall explicitly state what the requirement is for each numbered group. For example, “It is mandatory to support at least one of these options“, or, “It is mandatory to support exactly one of these options“. To be completed as required. ETSI 16 ETSI EN 300 390-2 V1.l.l (2000-09) vl.l.l vl.l.l History March 2000 One-step Approval Procedure OAP 20000721: 2000-03-22 to 2000-07-21 September 2000 Publication I Document history I ETSI