ETSI EN 300 474-2-2003 Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) Profile requirement list and profile specific Implementation Conformance Sta_1.pdf

1、 ETSI EN 300 474-2 V1.2.1 (2003-09)European Standard (Telecommunications series) Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile requirement list and profile specificImplementation Conformance Statement (ICS) proforma;Part 2: Fixed radio Termination (FT)ETSI

2、ETSI EN 300 474-2 V1.2.1 (2003-09) 2 Reference REN/DECT-040107-2 Keywords access, DECT, generic, ICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif e

3、nregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in co

4、ntents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the docu

5、ment may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be re

6、produced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Me

7、mbers. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 3 Contents Intellectual Prop

8、erty Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .7 4 Conformance requirement concerning profile ICS 7 Annex A (normative): Requirement Lists for DECT FT8 A.1 General .8 A.1.1 Profile Requirement List (profile RL)8 A.1.2 General co

9、nditions9 A.2 Network (NWK) layer - FT: profile Requirement List (profile RL)9 A.2.1 Major capabilities.9 A.2.1.1 Entities 9 A.2.1.2 CC features .10 A.2.1.3 MM features11 A.2.1.4 SS features (services)12 A.2.1.5 LCE features .13 A.2.1.6 Procedures.13 A.2.2 Messages 15 A.2.2.1 Call control messages .

10、15 A.2.2.2 Mobility management messages.22 A.2.2.3 Connection-related and connection independent supplement service messages.28 A.2.2.4 Link control entity messages 28 A.2.3 Information elements29 A.2.3.1 Fixed length information element support29 A.2.3.2 Variable length information element supporte

11、d30 A.2.3.3 Escape information elements support .34 A.2.4 Protocol error handling.35 A.3 Data Link Control (DLC) layer - FT: profile ICS 35 A.3.1 Capabilities.35 A.3.1.1 Services.35 A.3.1.1.1 C-plane services 35 A.3.1.1.2 U-plane services36 A.3.1.1.3 Management services 36 A.3.1.2 Procedures.36 A.3.

12、1.2.1 Generic signalling procedures.36 A.3.1.2.2 Class A procedures37 A.3.1.2.3 Broadcast procedures 37 A.3.1.2.4 LU1 procedures.37 A.3.1.2.5 Management procedures .37 A.3.1.3 Parameters.38 A.3.1.3.1 LU1 parameters.38 A.3.1.4 Messages.38 A.3.1.4.1 C-plane PDUs .38 A.4 Medium Access Control (MAC) lay

13、er - FT: profile ICS .39 A.4.1 Major capabilities.39 A.4.1.1 Services.39 A.4.1.1.1 Connection oriented control services 39 A.4.1.1.2 Broadcast control services.40 ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 4 A.4.1.1.3 Multiplexing services 40 A.4.1.1.4 Management services 41 A.4.1.2 Procedures.42 A.4.1

14、.2.1 Connection setup procedures 42 A.4.1.2.2 Connection data transfer procedures .42 A.4.1.2.3 Connection handover procedures 42 A.4.1.2.4 Connection release procedures43 A.4.1.2.5 Broadcast procedures 43 A.4.1.2.6 CSF multiplexing procedures43 A.4.1.2.7 Layer management procedures43 A.4.1.3 Other

15、capabilities 44 A.4.2 Messages 44 A.4.2.1 A-Field44 A.4.2.1.1 A-field header - B-field identification.44 A.4.2.2 A-Field Messages .45 A.4.2.2.1 Paging tail messages supported.45 A.4.2.2.2 PTmessages information type .45 A.4.2.2.3 Mac control messages supported.46 A.4.2.2.4 Broadcast and connectionle

16、ss (BCL) messages 46 A.5 Physical layer - FT: profile ICS .47 A.5.1 Physical layer procedures.47 Annex B (normative): GAP profile-specific ICS proforma for FT .48 B.1 Introduction for completing the profile-specific ICS proforma .48 B.1.1 Purposes and structure48 B.1.2 Instructions for completing th

17、e profile-specific ICS proforma.50 B.2 Identification of the implementation 50 B.2.1 Date of statement50 B.2.2 Implementation Under Test (IUT) identification .50 B.2.3 System Under Test (SUT) identification50 B.2.4 Product supplier51 B.2.5 Client identification51 B.2.6 Contact person identification5

18、1 B.3 Identification of the profile.52 B.3.1 Defect report numbers and amendments implemented.52 B.3.2 Addenda implemented52 B.4 Global statement of conformance.52 B.5 Capabilities.53 B.5.1 NWK profile-specific ICS proforma for FT.53 B.5.1.1 General requirements53 B.5.1.2 Application features53 B.5.

19、1.3 Application procedures .53 B.5.1.4 Management procedures .54 B.5.2 DLC profile-specific ICS proforma for FT 54 B.5.2.1 Services.54 B.5.3 MAC profile-specific ICS proforma for FT .54 B.5.3.1 Services.54 B.5.3.1.1 Extended frequency allocation service54 B.5.4 PHY Profile-specific ICS proforma for

20、FT 55 B.5.4.1 Requirements 55 Annex C (informative): Bibliography.56 History 57 ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, i

21、f any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are availab

22、le on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web serve

23、r) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DECT). The present document is part 2 of a multi-part deliverable. Full details of th

24、e entire series can be found in EN 300 474-1 9. Annex A contains the requirement lists for the Fixed radio Termination (FT) Generic Access Profile. Annex B contains the profile-specific ICS proforma for the FT Generic Access Profile. National transposition dates Date of adoption of this EN: 5 Septem

25、ber 2003 Date of latest announcement of this EN (doa): 31 December 2003 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 June 2004 Date of withdrawal of any conflicting National Standard (dow): 30 June 2004 ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 6 1 Scope Th

26、e present document provides the profile Requirement List and profile-specific Implementation Conformance Statement (profile ICS) proforma for the Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) at the Fixed radio Termination (FT) as defined in EN 300 444 2 in complia

27、nce with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 8. The supplier of an implementation which is claimed to conform to EN 300 444 2 is required to complete a copy of the Protocol Implementation Conformance Statement (PICS) proforma EN 300 476-4 3,

28、 EN 300 476-5 4, EN 300 476-6 5 and EN 300 476-7 6 with the replacements from annex A of the present document, as well as, a copy of the and profile-specific ICS proforma provided in the annex B of the present document. 2 References The following documents contain provisions which, through reference

29、 in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version appl

30、ies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI EN 300 175-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 5: Network (NWK) layer“. 2 ETSI EN 300 444: “Digit

31、al Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP)“. 3 ETSI EN 300 476-4: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 4: Network (NWK) layer - Fixed radio Termination (FT)“.

32、 4 ETSI EN 300 476-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 5: Data Link Control (DLC) layer - Fixed radio Termination (FT)“. 5 ETSI EN 300 476-6: “Digital Enhanced Cordless Telecommunications

33、(DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 6: Medium Access Control (MAC) layer - Fixed radio Termination (FT)“. 6 ETSI EN 300 476-7: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conforman

34、ce Statement (PICS) proforma; Part 7: Physical layer“. 7 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 8 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Confor

35、mance testing methodology and framework - Part 7: Implementation Conformance Statements“. 9 ETSI EN 300 474-1: “Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 1

36、: Portable radio Termination (PT)“. ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 7 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-7 8, EN 300 444 2 and ISO/IEC 9646-1 7 apply. 3.2 Abbreviations For the purposes of

37、the present document, the abbreviations defined in ISO/IEC 9646-1 7 and EN 300 444 2 apply. 4 Conformance requirement concerning profile ICS The supplier of a protocol implementation which is claimed to conform to the portable termination specific requirements of EN 300 444 2 shall verify that his p

38、rotocol implementation meets the profile Requirements Lists (RLs) for each DECT protocol layer, contained in annex A of the present document, and shall complete a copy of the profile-specific ICS proforma provided in annex B and shall provide the information necessary to identify both the supplier a

39、nd the implementation. ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 8 Annex A (normative): Requirement Lists for DECT FT A.1 General The supplier of a protocol implementation which is claimed to conform to the portable termination specific requirements of EN 300 444 2 shall verify that his particular (NW

40、K, DLC and MAC) layer protocol implementation meets the profile RL for this layer. For this, he shall complete a copy of the corresponding layer PICS proforma contained in annex A of EN 300 476-4 3, EN 300 476-5 4, EN 300 476-6 5 and EN 300 476-7 6 updated with the requirements from this annex. A.1.

41、1 Profile Requirement List (profile RL) The profile Requirement List (profile RL) for the NWK, DLC, MAC and PH layer as defined in this clause is based on EN 300 476-4 3, EN 300 476-5 4, EN 300 476-6 5 and EN 300 476-7 6. For every capability listed in EN 300 476-4 3, EN 300 476-5 4, EN 300 476-6 5

42、and EN 300 476-7 6, the profile requirements are expressed by restriction upon allowed support answers in EN 300 476-4 3, EN 300 476-5 4, EN 300 476-6 5 and EN 300 476-7 6 depending on whether the implementation is to work in Residential/Business (R/B) or Public (P) environment. The profile RL is pr

43、oduced by copying selected tables from EN 300 476-4 3, EN 300 476-5 4, EN 300 476-6 5 and EN 300 476-7 6, removing the column(s) to be completed by the supplier, and adding a new set of columns giving the new profile requirements, both in terms of the status and allowed values. The tables are refere

44、nced by preceding it with EN 300 476-4 3, EN 300 476-5 4, EN 300 476-6 5 or EN 300 476-7 6 as relevant. Profile status column: Where it has been seen as necessary two profile status columns are provided one for Residential/Business (R/B) environment and one for Public (P) environment. The standardiz

45、ed symbols for the status column are as follows: m or M mandatory - the capability is required to be supported; o or O optional - the capability may be supported or not; n/a or N/A not applicable - in the given context, it is impossible to use the capability; x or X prohibited (excluded) - there is

46、a requirement not to use this capability in the given context; o.i or O.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is defined immediately following

47、the table; ci or Ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately following the table or which is defined in the

48、 general condition table below; i or I out-of-scope - this capability is outside the scope of the given specification, and hence irrelevant and not subject to conformance testing. This status is in particular applicable for data fields which are reserved for future use. The structure of such fields

49、has to be supported, but the value is undefined and thus to be ignored. Reference column: The reference column gives reference to EN 300 444 2, except where explicitly stated otherwise. ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 9 A.1.2 General conditions The note in table A.1 is generally defined to apply to the tables in the following clauses where indicated. Table A.1: General condition table Condition identifier Condition definition NOTE A The status of the rel