ETSI EN 300 698-2-2009 Electromagnetic compatibility and Radio spectrum Matters (ERM) Radio telephone transmitters and receivers for the maritime mobile service operating in the VH_1.pdf

1、 ETSI EN 300 698-2 V1.2.1 (2009-12)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Radio telephone transmitters and receiversfor the maritime mobile service operatingin the VHF bands used on inland waterways;Part 2: Harmonized EN

2、 covering essential requirementsof article 3.2 of the R Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ET

3、SI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Forewor

4、d This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Dire

5、ctive 98/34/EC (as amended) i.1 laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities

6、 referencing the Directive 1999/5/EC i.3 of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R Part 2: “Harmonized EN covering essential requirements of article 3.2 of the R Pa

7、rt 3: “Harmonized EN covering essential requirements of article 3.3 (e) of the R - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this cla

8、use were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the

9、latest edition of the referenced document (including any amendments) applies. 1 ETSI EN 300 698-1 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways;

10、 Part 1: Technical characteristics and methods of measurement“. 2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the

11、 referenced document (including any amendments) applies. i.1 Council Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. i.2 ETSI TR 100 028: “Electromagnetic co

12、mpatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 7i.3 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal

13、 equipment and the mutual recognition of their conformity (R - the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report; - the recorded value of the measurement uncertainty shall be, for each measurement, equal to or lower than the figures i

14、n table 1. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated in accordance with TR 100 028 i.2 and shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of respectively 95 % and 95,4

15、5 % in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian). ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 13Table 1 is based on such expansion factors. Table 1: Absolute measurement uncertainties: maximum values Parameter Maximum uncertainty RF freque

16、ncy 1 x 10-7RF power 0,75 dB Maximum frequency deviation: - within 300 Hz to 6 kHz of audio frequency; - within 6 kHz to 25 kHz of audio frequency 5 % 3 dB Deviation limitation 5 % Adjacent channel power 5 dB Conducted spurious emission of transmitter 4 dB Conducted emission of receiver 3 dB Two-sig

17、nal measurement 4 dB Three-signal measurement 3 dB Radiated emission of transmitter 6 dB Radiated emission of receiver 6 dB Transmitter transient time 20 % Transmitter transient frequency 250 Hz Receiver desensitization (duplex operation) 0,5 dB 5.3 Essential radio test suites 5.3.1 Transmitter freq

18、uency error The test specified in EN 300 698-1 1, clause 8.1.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.1.2 in order to prove compliance with the requirement. 5.3.2 Transmitter carrier power The test specified in EN 300 698-1 1, clause 8.2.2 shall be c

19、arried out. The results obtained shall be compared to the limits in clause 4.2.2.2 in order to prove compliance with the requirement. 5.3.3 Transmitter frequency deviation The test specified in EN 300 698-1 1, clause 8.3.2 shall be carried out. The results obtained shall be compared to the limits in

20、 clause 4.2.3.2 in order to prove compliance with the requirement. 5.3.4 Transmitter adjacent channel power The test specified in EN 300 698-1 1, clause 8.8.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.4.2 in order to prove compliance with the requiremen

21、t. 5.3.5 Transmitter conducted spurious emissions conveyed to the antenna The test specified in EN 300 698-1 1, clause 8.9.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.5.2 in order to prove compliance with the requirement. 5.3.6 Transient frequency behav

22、iour of the transmitter The test specified in EN 300 698-1 1, clause 8.11.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.6.2 in order to prove compliance with the requirement. ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 145.3.7 Transmitter cabinet radiation an

23、d conducted spurious emissions other than those conveyed to the antenna The test specified in EN 300 698-1 1, clause 8.12.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.7.2 in order to prove compliance with the requirement. 5.3.8 ATIS encoder frequency err

24、or (demodulated signal) The test specified in EN 300 698-1 1, clause B.2.2.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.8.2 in order to prove compliance with the requirement. 5.3.9 ATIS encoder modulation index The test specified in EN 300 698-1 1, claus

25、e B.2.3.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.9.2 in order to prove compliance with the requirement. 5.3.10 ATIS encoder modulation rate The test specified in EN 300 698-1 1, clause B.2.4.2 shall be carried out. The results obtained shall be compa

26、red to the limits in clause 4.2.10.2 in order to prove compliance with the requirement. 5.4 Other test specifications 5.4.1 General The requirements in clauses 4.2.11 to 4.2.18 inclusive have been set on the assumption that the test specifications in clauses 5.4.2 to 5.4.9 will be used to verify the

27、 performance of the equipment. 5.4.2 Receiver maximum usable sensitivity The test specified in EN 300 698-1 1, clause 9.3.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.11.2 in order to prove compliance with the requirement. 5.4.3 Receiver co-channel rejec

28、tion The test specified in EN 300 698-1 1, clause 9.4.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.12.2 in order to prove compliance with the requirement. 5.4.4 Receiver adjacent channel selectivity The test specified in EN 300 698-1 1, clause 9.5.2 shal

29、l be carried out. The results obtained shall be compared to the limits in clause 4.2.13.2 in order to prove compliance with the requirement. 5.4.5 Receiver spurious response rejection The test specified in EN 300 698-1 1, clause 9.6.2 shall be carried out. The results obtained shall be compared to t

30、he limits in clause 4.2.14.2 in order to prove compliance with the requirement. 5.4.6 Receiver intermodulation response The test specified in EN 300 698-1 1, clause 9.7.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.15.2 in order to prove compliance with t

31、he requirement. ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 155.4.7 Receiver blocking or desensitization The test specified in EN 300 698-1 1, clause 9.8.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.16.2 in order to prove compliance with the requirement. 5.4

32、.8 Receiver conducted spurious emissions conveyed to the antenna The test specified in EN 300 698-1 1, clause 9.9.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.17.2 in order to prove compliance with the requirement. 5.4.9 Receiver radiated spurious emissi

33、ons The test specified in EN 300 698-1 1, clause 9.14.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.18.2 in order to prove compliance with the requirement. ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 16Annex A (normative): HS Requirements and conformance Test

34、 specifications Table (HS-RTT) The HS Requirements and conformance Test specifications Table (HS-RTT) in table A.1 serves a number of purposes, as follows: it provides a statement of all the requirements in words and by cross reference to (a) specific clause(s) in the present document or to (a) spec

35、ific clause(s) in (a) specific referenced document(s); it provides a statement of all the test procedures corresponding to those requirements by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it qualifies each re

36、quirement to be either: - Unconditional: meaning that the requirement applies in all circumstances; or - Conditional: meaning that the requirement is dependent on the manufacturer having chosen to support optional functionality defined within the schedule. in the case of Conditional requirements, it

37、 associates the requirement with the particular optional service or functionality; it qualifies each test procedure to be either: - Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the referenc

38、ed procedures; - Other: meaning that the test procedure is illustrative but other means of demonstrating compliance with the requirement are permitted. Table A.1: HS Requirements and conformance Test specifications Table (HS-RTT) Harmonized Standard EN 300 698-2 The following requirements and test s

39、pecifications are relevant to the presumption of conformity under the article 3.2 of the R those designated “O“ make up the Other Test Suite; for those designated “X“ there is no test specified corresponding to the requirement. The completion of all tests classified “E“ as specified with satisfactor

40、y outcomes is a necessary condition for a presumption of conformity. Compliance with requirements associated with tests classified “O“ or “X“ is a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivalent test or by manufacturers ass

41、ertion supported by appropriate entries in the technical construction file. Clause Number Identification of clause(s) defining the test specification in the present document unless another document is referenced explicitly. Where no test is specified (that is, where the previous field is “X“) this f

42、ield remains blank. ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 18Annex B (informative): The EN title in the official languages The enlargement of the European Union (EU) resulted in a requirement from the EU for a larger number of languages for the translation of the titles of Harmonized Standards and

43、mandated ENs that are to be listed in the Official Journal to support the implementation of this legislation. For this reason the title translation concerning the present document can be consulted via the e-approval application. ETSI ETSI EN 300 698-2 V1.2.1 (2009-12) 19History Document history V1.1.1 August 2000 Publication V1.2.1 August 2009 One-step Approval Procedure OAP 20091129: 2009-08-01 to 2009-11-30 V1.2.1 December 2009 Publication