ETSI EN 300 718-2-2018 Avalanche Beacons operating at 457 kHz Transmitter-receiver systems Part 2 Harmonised Standard for features for emergency services (V2 1 1).pdf

1、 ETSI EN 300 718-2 V2.1.1 (2018-01) Avalanche Beacons operating at 457 kHz; Transmitter-receiver systems; Part 2: Harmonised Standard for features for emergency services HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 2 Reference REN/ERM-TG28-512-2 Keywords harmonised standard,

2、radio, safety, SAR, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present documen

3、t can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case

4、of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document

5、 may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/porta

6、l.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modifie

7、d without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks o

8、f ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 3 Contents Intellectual Property

9、 Rights 5g3Foreword . 5g3Modal verbs terminology 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g34 Technical requirements specifications . 8g34.1 Environmental profile . 8g34.2 Environmental conformance requireme

10、nts . 8g34.2.1 General requirements 8g34.2.2 Drop test on hard surface 8g34.2.2.1 Description 8g34.2.2.2 Method of measurement 8g34.2.2.3 Requirements 8g34.2.3 Temperature tests 9g34.2.3.1 General 9g34.2.3.2 Dry heat cycle . 9g34.2.3.3 Low temperature cycle 9g34.2.3.4 Requirements 9g34.2.4 Immersion

11、 test 9g34.2.4.1 Method of measurement 9g34.2.4.2 Requirements 9g34.2.5 Solar radiation . 10g34.2.5.1 Method of measurement 10g34.2.5.2 Requirements 10g34.2.6 Tensile test 10g34.2.6.1 Method of measurement 10g34.2.6.2 Requirements 10g34.3 Mechanical and electrical design conformance requirements 10g

12、34.3.1 Operational Requirements 10g34.3.2 Maintaining the transmit mode . 10g34.3.3 Operating time 11g34.3.4 Battery check 11g34.3.5 Carrying system 11g34.3.6 Operating instructions . 11g34.3.7 Short form operating instructions . 11g34.3.8 Operating and storage temperatures 11g34.4 Radio performance

13、 requirements . 12g34.4.1 Transmitter requirements 12g34.4.1.1 Minimum output field strength (H-field) 12g34.4.2 Receiver requirements 12g34.4.2.1 Changes in the received signal 12g34.4.2.1.1 Definition. 12g34.4.2.1.2 Requirement 12g35 Test conditions, power sources and ambient temperatures 12g35.1

14、Normal and extreme test conditions . 12g35.2 External test power source 12g35.3 Normal test conditions 12g35.3.1 Normal temperature and humidity 12g35.3.2 Normal test voltage . 13g35.4 Extreme test conditions 13g35.4.1 Extreme temperatures . 13g3ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 4 5.4.2 Extrem

15、e test voltages 13g35.4.2.1 General requirement 13g35.4.2.2 Procedure for tests at extreme temperatures 13g35.5 Measurement uncertainty . 13g3Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 15g3Annex B (normative): Simulated s

16、olar radiation source 16g3Annex C (informative): Change history . 17g3History 18g3ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 5 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to the

17、se essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest

18、 updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

19、 server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property o

20、f ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has

21、 been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.2 to provide one voluntary means of conforming to the essential requirements of Directi

22、ve 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the norm

23、ative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document implements requirements laid dow

24、n in Commission Decision 2001/148/EC i.3. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 18 December 2017 Date of latest announcement of this EN (doa): 31 March 2018 Dat

25、e of latest publication of new National Standard or endorsement of this EN (dop/e): 30 September 2018 Date of withdrawal of any conflicting National Standard (dow): 30 September 2019 ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 6 Modal verbs terminology In the present document “shall“, “shall not“, “shou

26、ld“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ET

27、SI ETSI EN 300 718-2 V2.1.1 (2018-01) 7 1 Scope The present document specifies technical characteristics and methods of measurements for avalanche beacons operating at 457 kHz transmitter-receiver systems. NOTE: The relationship between the present document and essential requirements of article 3.3g

28、 of Directive 2014/53/EU i.1 is given in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expecte

29、d location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ET

30、SI EN 300 718-1 (V2.1.1) (01-2018): “Avalanche Beacons operating at 457 kHz; Transmitter-receiver systems; Part 1: Harmonised standard for access to radio spectrum“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number)

31、or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee the

32、ir long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of t

33、he laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the

34、 European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.3 Commission Decision 2001/148/EC of 21 February 2001 on the application of Article 3(3)(e) of Directive 1999/5/EC to avalanche beacons. i.4

35、 EN 60068-2-5-2011: “Environmental testing. Tests. Test Sa. Simulated solar radiation at ground level and guidance for solar radiation testing“. i.5 ETSI TR 100 028 (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipmen

36、t characteristics“. ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 8 3 Definitions, symbols and abbreviations For the purposes of the present document, the terms and definitions, symbols and abbreviations given in ETSI EN 300 718-1 1, clause 3, apply. 4 Technical requirements specifications 4.1 Environment

37、al profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document which are identified as applicable i

38、n annex A at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 Environmental conformance requirements 4.2.1 General requirements Environmental tests shall be carried out before tests of the same equipment in respect to the other requirements o

39、f the present document are performed. The following tests shall be carried out in the order they appear in clause 4.2. Where electrical tests are required the equipment shall be powered by its internal battery. 4.2.2 Drop test on hard surface 4.2.2.1 Description The immunity against the effects of d

40、ropping is the ability of the equipment to maintain the specified mechanical and electrical performance after being subjected to a series of drops on a hard wooden test surface. 4.2.2.2 Method of measurement The test shall consist of a series of 6 drops, one on each surface. During the test the equi

41、pment shall be fitted with a suitable set of batteries and it shall be switched on in transmit mode. The test shall be carried out under normal temperature and humidity conditions. The hard wooden test surface shall consist of a piece of solid hard wood with a minimum thickness of 15 cm and a mass o

42、f 30 kg or more. The height of the lowest part of the equipment under test relative to the test surface at the moment of release shall be 1 m. Equipment shall be subjected to the present document configured for use as in operational circumstances. 4.2.2.3 Requirements After the test, the equipment s

43、hall be fully operational in both the transmit and the receive modes. The requirement shall be checked by interacting with another sample of the same equipment to form a transmitter - receiver pair. ETSI ETSI EN 300 718-2 V2.1.1 (2018-01) 9 4.2.3 Temperature tests 4.2.3.1 General The maximum rate of

44、 raising or reducing the temperature of the chamber in which the equipment is being tested shall be 1 C/minute. 4.2.3.2 Dry heat cycle The equipment shall be placed in a chamber of normal temperature. The temperature shall then be raised to and maintained at the upper extreme storage temperature (3

45、C) for a period of at least 10 hours. After this period any climatic control device provided in the equipment may be switched on and the chamber cooled to the upper extreme operating temperature (3 C). The cooling of the chamber shall be completed within 30 minutes. The equipment shall then be switc

46、hed on and shall be kept working continuously in transmitting mode for a period of two hours. The temperature of the chamber shall be maintained at the upper extreme operating temperature (3 C) during the two hour period. At the end of the test, and with the equipment still in the chamber, the chamb

47、er shall be brought to room temperature in not less than one hour. The equipment shall then be exposed to normal room temperature and humidity for not less than three hours before the next test is carried out. 4.2.3.3 Low temperature cycle The equipment shall be placed in a chamber at normal room te

48、mperature. Then the temperature shall be reduced to, and maintained at, the lower extreme storage temperature (3 C) for a period of at least 10 hours. The chamber shall be warmed to the lower extreme operating temperature (3 C). The warming of the chamber shall be completed within 30 (5) minutes. Th

49、e equipment shall then be switched on and shall be kept working continuously in transmitting mode for a period of two hours. The temperature of the chamber shall be then maintained at the lower extreme operating temperature (3 C) during the two hour period. At the end of the test, and with the equipment still in the chamber, the chamber shall be brought to room temperature in not less than one hour. The equipment shall then be exposed to normal room temperature for not less than three hours, or until moisture has dispersed, whichever is