ETSI EN 301 426-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Low data rate Land Mobile satellite Earth Stations (LMES) and Maritime Mobile satellite Eart_1.pdf

1、 ETSI EN 301 426 V2.1.2 (2016-11) Satellite Earth Stations and Systems (SES); Harmonised Standard for Low data rate Land Mobile satellite Earth Stations (LMES) and Maritime Mobile satellite Earth Stations (MMES) not intended for distress and safety communications operating in the 1,5 GHz/1,6 GHz fre

2、quency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 426 V2.1.2 (2016-11) 2 Reference REN/SES-00379 Keywords earth station, LMES, regulation, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FR

3、ANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be m

4、ade available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print,

5、the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this

6、and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduce

7、d or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction ex

8、tend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Membe

9、rs and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 426 V2.1.2 (2016-11) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 8g32 References 8g32.1 Norma

10、tive references . 8g32.2 Informative references 9g33 Definitions and abbreviations . 10g33.1 Definitions 10g33.2 Abbreviations . 10g34 Technical requirement specifications . 11g34.1 Environmental profile . 11g34.2 Conformance Requirements . 11g34.2.1 Unwanted emissions outside the bands . 11g34.2.1.

11、1 Justification . 11g34.2.1.2 Specification 11g34.2.1.3 Conformance tests . 13g34.2.2 Maximum unwanted emission within the bands . 13g34.2.2.1 Justification . 13g34.2.2.2 Specification 13g34.2.2.3 Conformance tests . 14g34.2.3 Control and Monitoring Functions (CMFs) 14g34.2.3.1 General 14g34.2.3.2 P

12、rocessor monitoring 14g34.2.3.2.1 Justification . 14g34.2.3.2.2 Specification 15g34.2.3.2.3 Conformance tests . 15g34.2.3.3 Transmit subsystem monitoring 15g34.2.3.3.1 Justification . 15g34.2.3.3.2 Specification 15g34.2.3.3.3 Conformance tests . 15g34.2.3.4 Power-on/Reset . 15g34.2.3.4.1 Justificati

13、on . 15g34.2.3.4.2 Specification 15g34.2.3.4.3 Conformance tests . 15g34.2.3.5 Control Channel reception 15g34.2.3.5.1 Justification . 15g34.2.3.5.2 Specification 16g34.2.3.5.3 Conformance tests . 16g34.2.3.6 Network control commands 16g34.2.3.6.1 Justification . 16g34.2.3.6.2 Specification 16g34.2.

14、3.6.3 Conformance test . 16g34.2.3.7 Initial burst transmission . 16g34.2.3.7.1 Justification . 16g34.2.3.7.2 Specification 17g34.2.3.7.3 Conformance tests . 17g34.2.4 Receiver Adjacent Channel Selectivity. 17g34.2.4.1 Justification . 17g34.2.4.2 Specification 17g34.2.4.3 Conformance test 17g34.2.5

15、Receiver Blocking Characteristics 17g34.2.5.1 Justification . 17g3ETSI ETSI EN 301 426 V2.1.2 (2016-11) 4 4.2.5.2 Specification 17g34.2.5.3 Conformance test 18g35 Testing for compliance with technical requirements 18g35.1 Environmental conditions for testing . 18g35.2 Radio test suites 18g35.2.1 Gen

16、eral 18g35.2.2 Measurement of unwanted emissions . 19g35.2.2.1 General 19g35.2.2.2 Test site . 19g35.2.2.3 Test method . 19g35.2.2.3.1 Installation . 19g35.2.2.3.2 Receive test equipment 20g35.2.2.4 Procedure 21g35.2.2.4.1 Test arrangements 21g35.2.2.4.2 Up to 1 000 MHz . 21g35.2.2.4.3 Above 1 000 M

17、Hz . 22g35.2.3 MES Control and Monitoring Functions (CMF) 22g35.2.3.1 General 22g35.2.3.2 Test arrangement . 23g35.2.3.3 Processor monitoring 23g35.2.3.3.1 Test method . 23g35.2.3.4 Transmit subsystem monitoring 24g35.2.3.4.1 Test method . 24g35.2.3.5 Power-on/Reset . 24g35.2.3.5.1 Test method . 24g

18、35.2.3.6 Control Channel reception 24g35.2.3.6.1 Test method . 24g35.2.3.7 Network control commands 25g35.2.3.7.1 Test method . 25g35.2.3.8 Initial burst transmission . 26g35.2.3.8.1 Test method . 26g35.2.4 Receiver Adjacent Channel Selectivity. 27g35.2.4.1 General 27g35.2.4.2 Test arrangement . 27g

19、35.2.4.3 Test procedures . 27g35.2.5 Receiver Blocking Characteristics 27g35.2.5.1 General 27g35.2.5.2 Test arrangement . 28g35.2.5.3 Test procedures . 28g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 29g3Annex B (informative

20、): Bibliography . 30g3History 31g3ETSI ETSI EN 301 426 V2.1.2 (2016-11) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members an

21、d non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/)

22、. Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the prese

23、nt document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.5 to provide one voluntary means of conform

24、ing to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.8. Once the present document is cited in the Official Journal of the European Union un

25、der that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. National

26、 transposition dates Date of adoption of this EN: 12 September 2016 Date of latest announcement of this EN (doa): 31 December 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 Jun

27、e 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must

28、 not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 426 V2.1.2 (2016-11) 6 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit a modular structure to cover all radio equipment under the Directive 2014/5

29、3/EU i.8. The modular structure is shown in ETSI EG 201 399 i.4. Figure 1: Void These requirements are in three major categories: emission limits: to protect other radio services from harmful interference generated by the Mobile Earth Station (MES) in normal use; MES Control and Monitoring Functions

30、 (CMF): to protect other radio services from unwanted transmissions from the MES. The CMF in each MES is capable of answering to commands from the Network Control Facilities (NCF) for its MES; Receiver performance specifications: to enable reception of a wanted signal in the presence of other high p

31、ower signals in the adjacent channel and/or adjacent band. The requirements have been selected to ensure an adequate level of compatibility with other radio services. The levels, however, do not cover extreme cases which may occur in any location but with a low probability of occurrence. The present

32、 document may not cover those cases where a potential source of interference which is producing individually repeated transient phenomena or a continuous phenomenon is present, e.g. a radar or broadcast site in the near vicinity. In such a case it may be necessary to use special protection applied t

33、o either the source of interference, or the interfered part or both. The present document does not contain any requirement, recommendation or information about the installation of the MESs. Following the WRC-03 decision i.6 to allocate to MSS the bands 1 518 MHz to 1 525 MHz (space to Earth) and 1 6

34、68 MHz to 1 675 MHz (Earth to space) and the conclusions of WRC-07 i.7, a new set of emission requirements for LMESs that are capable of transmitting in the frequency band from 1 668,0 MHz to 1 675,0 MHz is specified. The two parts of the L-band frequency allocations are treated as two sub-bands whi

35、ch may be used separately or in any combination. The standard L-band allocation is referenced in the present document as “sub-band 1“ and the extended L-band is referenced as “sub-band 2“. Table 2c is applicable for LMESs that are capable of transmitting in any combination of either or both of these

36、 sub-bands. Table 2c is recommended for all new LMESs including LMES that can only operate in sub-band 1. The applicant may choose between tables 2b and 2c for new LMESs that are capable of transmitting in only the sub-band 1. The applicant has to declare which alternative is used. The present docum

37、ent specifies a new set of receiver performance requirements for LMESs under the new Radio Equipment Directive 2014/53/EU i.8. The present document was based on ETSI TBR 026 i.2. The present document is also based on ETSI ETS 300 740 i.3 (see annex B) for Maritime Mobile Earth Stations (MMES) not in

38、tended for distress and safety communications. The determination of the parameters of the user earth stations using a given geo-stationary satellite for the protection of the spectrum allocated to that satellite is considered to be under the responsibility of the satellite operator or the satellite

39、network operators. For MESs operating in satellite networks using satellites which also provide radio navigation service and/or other safety services should note that such satellite network operators or satellite operators may require testing in addition to the present document to prove correct inte

40、rworking in order to avoid the MES causing harmful interference which endangers the functioning of these services. References to these requirements will be listed in annex A of the present document as they become known. ETSI ETSI EN 301 426 V2.1.2 (2016-11) 7 The present document is therefore intend

41、ed to cover the provisions of Directive 2014/53/EU i.8 (RE Directive) article 3.2 which states that “.radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“. Recital 10 of Directive 2014/53/EU i.8

42、 states that “in order to ensure that radio equipment uses the radio spectrum effectively and supports the efficient use of radio spectrum, radio equipment should be constructed so that: in the case of a transmitter, when the transmitter is properly installed, maintained and used for its intended pu

43、rpose it generates radio waves emissions that do not create harmful interference, while unwanted radio waves emissions generated by the transmitter (e.g. in adjacent channels) with a potential negative impact on the goals of radio spectrum policy should be limited to such a level that, according to

44、the state of the art, harmful interference is avoided; and, in the case of a receiver, it has a level of performance that allows it to operate as intended and protects it against the risk of harmful interference, in particular from shared or adjacent channels, and, in so doing, supports improvements

45、 in the efficient use of shared or adjacent channels“. Recital 11 of Directive 2014/53/EU i.8 states that “although receivers do not themselves cause harmful interference, reception capabilities are an increasingly important factor in ensuring the efficient use of radio spectrum by way of an increas

46、ed resilience of receivers against harmful interference and unwanted signals on the basis of the relevant essential requirements of Union harmonisation legislation“. As a consequence, the present document includes both transmitting and receiving parameters aiming to maximize the efficient use of rad

47、io spectrum. ETSI ETSI EN 301 426 V2.1.2 (2016-11) 8 1 Scope The present document applies to the following Mobile Earth Stations (MESs) radio equipment: Land Mobile Earth Stations (LMESs) radio equipment; and Maritime Mobile Earth Stations (MMESs) radio equipment not providing those distress and saf

48、ety functions required by the International Maritime Organization (IMO); which have the following characteristics: these LMESs could be either vehicle mounted or portable equipment; these MMESs are installable equipment on ships; these MESs operate with user bit-rates of up to 9,6 kbits/s; these MES

49、s could consist of a number of modules including a keyboard interface to the user; these MESs are operating as part of a satellite network used for the distribution and/or exchange of information between users; this radio equipment is capable of operating in all or any part of the frequency bands given in table 1a. Table 1a: Mobile Satellite Service frequency bands Sub-Band Direction of transmission MSS frequency bands 1 Transmit 1 (Earth to space) 1 626,5 MHz to 1 660,5 MHz Receive 1 (space to Earth) 1 525,0 MHz to 1 559,0 MHz 2