ETSI EN 301 435-1-2008 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) Technical characteristics for SRD equipment using Ultra WideBand tec_1.pdf

1、 ETSI EN 302 435-1 V1.2.1 (2008-04)European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Short Range Devices (SRD);Technical characteristics for SRD equipment usingUltra WideBand technology (UWB);Building Material Analysis and Classification equi

2、pment applicationsoperating in the frequency band from 2,2 GHz to 8 GHz;Part 1: Technical characteristics and test methodsETSI ETSI EN 302 435-1 V1.2.1 (2008-04) 2 Reference DEN/ERM-TG31C-001-1 Keywords radar, radio, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRAN

3、CE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be

4、 made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version

5、 kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If

6、you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to repro

7、duction in all media. European Telecommunications Standards Institute 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of it

8、s Members and of the 3GPP Organizational Partners. ETSI ETSI EN 302 435-1 V1.2.1 (2008-04) 3 Contents Intellectual Property Rights5 Foreword.5 1 Scope 7 2 References 7 2.1 Normative references .8 2.2 Informative references8 3 Definitions, symbols and abbreviations .8 3.1 Definitions8 3.2 Symbols9 3.

9、3 Abbreviations .10 4 Technical requirement specifications.10 4.1 General requirements .10 4.2 Presentation of equipment for testing purposes10 4.2.1 Choice of model for testing 11 4.2.2 Auxiliary test equipment.11 4.2.3 Declarations by the provider.11 4.2.4 Marking and equipment identification11 4.

10、3 Mechanical and electrical design11 4.3.1 General11 4.3.2 Controls 11 4.3.3 Transmitter shut-off facility11 4.4 Other device emissions.12 5 Test conditions, power sources and ambient temperatures 12 5.1 Test conditions .12 5.2 Test power source.12 5.2.1 External test power source12 5.2.2 Internal t

11、est power source .12 5.3 Normal test conditions13 5.3.1 Normal temperature and humidity13 5.3.2 Normal test power source .13 5.3.2.1 Internal battery power source13 5.3.2.2 Regulated lead-acid battery power sources .13 5.3.2.3 Other power sources13 6 General conditions13 6.1 Radiated measurement arr

12、angements .13 6.2 Modes of operation of the transmitter 14 6.3 Measuring receiver.14 7 Interpretation of results 14 7.1 Measurement uncertainty .14 7.1.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty15 7.1.2 Measurement uncertainty is greater than the maximum accept

13、able uncertainty.15 7.2 Other emissions from device circuitry16 8 Methods of measurement and limits for transmitter parameters 16 8.1 General .16 8.2 Permitted range of operating frequencies.16 8.2.1 Definition16 8.2.2 Method of measurement .17 8.2.3 Frequency range18 8.3 Emissions .18 8.3.1 Undesir

14、ed UWB emissions from the transmitter 18 8.3.1.1 Definitions.18 ETSI ETSI EN 302 435-1 V1.2.1 (2008-04) 4 8.3.1.2 Method of measurement18 8.3.1.2.1 Method of measurement of the Total Emissions (TE).19 8.3.1.2.2 Method of measurement of the Other Emissions (OE)21 8.3.1.2.3 Method of calculation of th

15、e maximum mean undesired UWB emission of the equipment (UE).21 8.3.1.3 Limits 22 8.3.2 Other Emissions (OE).22 8.3.2.1 Definition 22 8.3.2.2 Method of measurement22 8.3.2.3 Limits 22 8.3.3 Total Power spectral density (UE-TP)22 8.3.3.1 Definitions.22 8.3.3.2 Method of measurement23 8.3.3.3 Limits 23

16、 8.4 Pulse Repetition Frequency (PRF) .24 8.4.1 Definitions 24 8.4.2 Declaration24 8.4.3 Limits24 8.5 Listen Before Talk (LBT).24 8.5.1 Definition24 8.5.2 Function of LBT .25 8.5.3 Method of measurement .27 8.5.3.1 Measurement procedure27 8.5.3.2 Test set-up.27 8.5.4 Limits29 8.5.5 Test signal defin

17、ition for LBT-mechanism.30 8.5.6 Design requirements .31 9 Methods of measurement and limits for receiver parameters.31 9.1 Receiver spurious emissions.31 Annex A (normative): Radiated measurements 32 A.1 Test sites and general arrangements for measurements involving the use of radiated fields.32 A.

18、1.1 Anechoic chamber32 A.1.2 Anechoic chamber with a conductive ground plane.33 A.1.3 Test antenna34 A.1.4 Measuring antenna .34 A.2 Guidance on the use of radiation test sites .35 A.2.1 Verification of the test site .35 A.2.2 Preparation of the DUT 35 A.2.3 Power supplies to the DUT.35 A.2.4 Range

19、length.35 A.2.5 Site preparation 36 A 2.6 General requirements for RF cables .36 Annex B (normative): Design requirements37 Annex C (informative): Measurement antenna and preamplifier specifications .38 Annex D (normative): Definition of the representative wall and procedure for measurement of the u

20、ndesired emissions.39 D.1 Representative wall definition for measuring the undesired emissions and LBT function39 D.2 Procedure for measurement the wall attenuation .40 D.3 Typical representative wall measurement result 41 Annex E (informative): Bibliography.42 History 43 ETSI ETSI EN 302 435-1 V1.2

21、.1 (2008-04) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intell

22、ectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investi

23、gation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard

24、(Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). Equipment covered by the present document operates in accordance with ECC Decision ECC/DEC(07)01 on Building Material Analysis (BMA) devices. For non EU countries

25、 the present document may be used for regulatory (Type Approval) purposes. The present document is part 1 of a multi-part deliverable covering Ultra WideBand (UWB) Building Material Analysis (BMA) and Classification equipment applications operating in the frequency band from 2,2 GHz to 8 GHz, as ide

26、ntified below: Part 1: “Technical characteristics and test methods“; Part 2: “Harmonized EN covering the essential requirements of article 3.2 of the R b) equipment fitted with an integral antenna; c) handheld devices. The present document does not apply to: UWB communication devices; and Ground pen

27、etrating radar devices; and through-wall radar imaging devices; as defined in ITU-R Recommendation SM.1754 6. The present document specifies the equipment which is designed to not radiate into the free space. It is designed to function only when positioned such that it radiates directly into the abs

28、orptive material such as walls and other building materials which absorb emissions. The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. 2 References References are either spec

29、ific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. Non-specific reference may be made only to a complete document or a part thereof and only in the following cases: - if it is accepted that it

30、 will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. For online re

31、ferenced documents, information sufficient to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the reference should, as far as possible, remain valid for the expected life of the

32、 document. The reference shall include the method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee

33、their long term validity. ETSI ETSI EN 302 435-1 V1.2.1 (2008-04) 8 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the

34、referenced document (including any amendments) applies. 1 CISPR 16-1 (2003): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immunity measuring apparatus“. 2 CEN EN 206-1 (2000): “Concrete - Part 1: Specification, Performance, Product

35、ion and Conformity“. 3 ETSI TR 100 028 (all parts) (V1.4.1): “ Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 4 ETSI TR 102 273 (all parts) (V1.2.1): “Electromagnetic compatibility and Radio spectrum Matter

36、s (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties“. 5 ANSI C63.5 (2006): “American National Standard for Calibration of Antennas Used for Radiated Emission Measurements in Electromagnetic Interference (EMI)“. 2.2 I

37、nformative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. 6 ITU-R Reco

38、mmendation SM.1754: “Measurement techniques of ultra-wideband transmissions“. 7 ITU-R Recommendation SM 1538: “Technical and operating parameters and spectrum requirements for short-range radiocommunication devices“. 8 ETSI TR 102 070-2: “Electromagnetic compatibility and Radio spectrum Matters (ERM

39、); Guide to the application of harmonized standards to multi-radio and combined radio and non-radio equipment; Part 2: Effective use of the radio frequency spectrum“. 9 CEPT/ERC/REC 74-01E (2005): “Unwanted emissions in the spurious domain“. 10 CENELEC EN 55022: “Information technology equipment - R

40、adio disturbance characteristics - Limits and methods of measurement“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: activity factor: effective transmission time ratio, actual on-the-air time divided by a

41、ctive session time or actual on-the-air emission time within a given time window clutter: undesired radar reflections (echoes) e.g. from inhomogenities, interfaces, gravel stones, cavities in building material structures integral antenna: permanent fixed antenna, which may be built-in, designed as a

42、n indispensable part of the equipment Listen Before Talk (LBT): mechanism to avoid signal transmission in the presence of other radio service signals Pulse Repetition Frequency (PRF): inverse of the Pulse Repetition Interval, averaged over a sufficiently long time to cover all PRI variations ETSI ET

43、SI EN 302 435-1 V1.2.1 (2008-04) 9 radiated measurements: measurements which involve the absolute measurement of a radiated field spatial resolution: ability to discriminate between two adjacent targets SRD: Equipment defined to operate on a non-interference, no protection from interference basis (a

44、s also defined in ITU-R Recommendation SM.1538 7) Total Power (TP): integration of the undesired emissions in the whole area around the BM and/or square4 scattered/reflected emissions from the building material to be investigated; and/or square4 residual emissions through the building material. 3.2

45、Symbols For the purposes of the present document, the following symbols apply: cl1 cable loss 1 cl2 cable loss 2 E Electrical field strength ER relative dielectric constant of earth materials Erms Average electrical field strength measured as root mean squaref frequency fc frequency at which the emi

46、ssion is the peak power at maximumGLNAGain of the measurement LNAGA Gain of the measurement antennaG(f) Antenna gain over frequency fHHighest frequency of the frequency band of operation fL Lowest frequency of the frequency band of operation P PowerPe.i.r.p. spectral power density Pm measured spectr

47、al power Pwall, e.i.r.p. undesired spectral power density Pvictim power of a different device at the BMA R Distance rms Root mean square t time TPpulse rise time ZF0 Free space wave impedance wavelength c velocity of light in a vacuum R range resolution t time interval between the arrivals of two si

48、gnals from targets separated in range by R ETSI ETSI EN 302 435-1 V1.2.1 (2008-04) 103.3 Abbreviations For the purposes of the present document, the following abbreviations apply: BMA Building Material Analysis CEPT Confrence Europenne des administrations de Postes et des Tlcommunications CW Continu

49、ous Wave dB deciBel dBi gain in deciBel relative to an isotropic antenna dBm deciBel reference to 1 mW DUT Device Under Test e.i.r.p. equivalent isotropically radiated power ECC Electronic Communications Committee EMC Electro-Magnetic Compatibility ERC European Radiocommunication Committee IT Information Technology LBT Listen Before Talk LNA Low Noise Amplifier MSS Mobile Satellite Service OE Other Emissions PRF Pulse Repetition Frequency PRI Pulse Repetition Interval PSD Power Spectral Density R - the type designation. This is the man