ETSI EN 301 473-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Aircraft Earth Stations (AES) providing Aeronautical Mobile Satellite Service (AMSS) Mobile .pdf

1、 ETSI EN 301 473 V2.1.2 (2016-11) Satellite Earth Stations and Systems (SES); Harmonised Standard for Aircraft Earth Stations (AES) providing Aeronautical Mobile Satellite Service (AMSS)/ Mobile Satellite Service (MSS) and/or the Aeronautical Mobile Satellite on Route Service (AMS(R)S)/ Mobile Satel

2、lite Service (MSS), operating in the frequency band below 3 GHz covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 473 V2.1.2 (2016-11) 2 Reference REN/SES-00389 Keywords aeronautical, AMSS, earth station, mobile, MSS, satelli

3、te ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from:

4、 http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or percei

5、ved difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revisi

6、on or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/Commite

7、eSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written aut

8、horization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and L

9、TE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 473 V2.1.2 (2016-11) 3 Contents Intellectual Property Rights 9g3Foreword . 9g3Modal verbs t

10、erminology 9g3Introduction 9g31 Scope 11g32 References 12g32.1 Normative references . 12g32.2 Informative references 12g33 Definitions and abbreviations . 13g33.1 Definitions 13g33.2 Abbreviations . 14g34 General . 15g34.1 Presentation of equipment for testing purposes 15g34.2 Aircraft earth station

11、s . 15g34.3 Description of equipment . 16g35 Requirements for AES transmitting in the band 1 610 MHz to 1 626,5 MHz . 17g35.1 Unwanted emissions limits outside the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to 1 628,5 MHz (carrier-on) . 17g35.1.1 Purpose . 17g35.1.2 Conformance requireme

12、nts . 17g35.1.3 Method of test . 17g35.1.4 Peak measurement 18g35.1.5 Average measurement . 18g35.1.6 Test requirements 18g35.2 Unwanted emissions limits within the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to 1 628,5 MHz (carrier-on) . 19g35.2.1 Purpose . 19g35.2.2 Conformance requirem

13、ents . 19g35.2.3 Method of test . 20g35.2.4 Measurement method 21g35.2.5 Test requirements 21g35.3 EIRP density limits within the operational band 21g35.3.1 Purpose . 21g35.3.2 Conformance requirements . 21g35.3.3 Method of test . 22g35.3.4 Peak Limit Test . 22g35.3.5 Mean Limit Test . 22g35.3.6 Tes

14、t requirements 23g35.4 Unwanted emissions limits (carrier-off) . 23g35.4.1 Purpose . 23g35.4.2 Conformance requirements . 23g35.4.3 Method of test . 23g35.4.4 Peak measurement 24g35.4.5 Average measurement . 24g35.4.6 Test requirements 24g35.5 AES Control and Monitoring Functions (CMF) . 24g35.5.1 S

15、pecial test equipment 24g35.5.2 Self-monitoring functions . 25g35.5.2.1 Processor monitoring 25g35.5.2.1.1 Purpose 25g35.5.2.1.2 Conformance requirements 25g35.5.2.1.3 Method of test 25g35.5.2.2 Transmit frequency generation sub-system monitoring 25g3ETSI ETSI EN 301 473 V2.1.2 (2016-11) 4 5.5.2.2.1

16、 Purpose 25g35.5.2.2.2 Conformance requirements 25g35.5.2.2.3 Method of test 25g35.5.3 Network control authorization and reception 25g35.5.3.1 Network control authorization 25g35.5.3.1.1 Purpose 25g35.5.3.1.2 Conformance requirements 26g35.5.3.1.3 Method of test 26g35.5.3.1.4 Test procedure . 26g35.

17、5.3.1.5 Test requirement 26g35.5.3.2 Network control reception transmit frequency control 26g35.5.3.2.1 Purpose 26g35.5.3.2.2 Conformance requirements 27g35.5.3.2.3 Method of test 27g35.5.3.2.4 Test procedure . 27g35.5.3.2.5 Test requirement 27g35.6 Equipment identity . 27g35.6.1 Purpose . 27g35.6.2

18、 Conformance requirements . 27g35.6.3 Method of test . 28g35.6.4 Test procedure 28g35.6.5 Test requirements 28g36 Requirements for AES transmitting in the band 1 626,5 MHz to 1 660,5 MHz and the band 1 668,0 MHz to 1 675,0 MHz 28g36.1 Unwanted emissions limits outside the band 1 626,5 MHz to 1 660,5

19、 MHz and the band 1 660,5 MHz to 1 662,5 MHz and also outside the band 1 666,0 MHz to 1 668,0 MHz, the band 1 668,0 MHz to 1 675,0 MHz and the band 1 675,0 MHz to 1 677,0 MHz 28g36.1.1 Purpose . 28g36.1.2 Conformance requirements . 29g36.1.3 Testing for carrier on state 35g36.1.3.1 Method of test .

20、35g36.1.3.2 Measurement method 36g36.1.3.3 Test requirements 36g36.1.4 Testing for carrier off state . 36g36.1.4.1 Method of test . 36g36.1.4.2 Peak measurement method 36g36.1.4.3 Average measurement . 37g36.1.4.4 Test requirements 37g36.2 Unwanted emissions limits within the band 1 626,5 MHz to 1 6

21、60,5 MHz and the band 1 660,5 MHz to 1 662,5 MHz and also within the band 1 666,0 MHz to 1 668,0 MHz, the band 1 668,0 MHz to 1 675,0 MHz and the band 1 675,0 MHz to 1 677,0 MHz 37g36.2.1 Purpose . 37g36.2.2 Conformance requirements . 38g36.2.2.1 General 38g36.2.2.2 Specification 1: Carrier-on state

22、 38g36.2.2.3 Specification 2: Carrier-off state . 40g36.2.3 Testing for carrier on state 41g36.2.3.1 Method of test . 41g36.2.3.2 Measurement method 41g36.2.3.3 Test requirements 41g36.2.4 Testing for carrier off state . 42g36.2.4.1 Method of test . 42g36.2.4.2 Peak measurement method 42g36.2.4.3 Av

23、erage measurement . 42g36.2.4.4 Test requirements 42g36.3 AES Control and Monitoring Functions (CMF) . 43g36.3.1 Special test equipment 43g36.3.2 Self-monitoring functions . 43g36.3.2.1 Processor monitoring 43g36.3.2.1.1 Purpose 43g36.3.2.1.2 Conformance requirements 43g3ETSI ETSI EN 301 473 V2.1.2

24、(2016-11) 5 6.3.2.1.3 Method of test 43g36.3.2.2 Transmit frequency generation sub-system monitoring 43g36.3.2.2.1 Purpose 43g36.3.2.2.2 Conformance requirements 43g36.3.2.2.3 Method of test 44g36.3.3 Network control authorization and reception 44g36.3.3.1 Network control authorization 44g36.3.3.1.1

25、 Purpose 44g36.3.3.1.2 Conformance requirements 44g36.3.3.1.3 Method of test 44g36.3.3.1.4 Test procedure . 44g36.3.3.1.5 Test requirement 45g36.3.3.2 Network control reception transmit frequency control 45g36.3.3.2.1 Purpose 45g36.3.3.2.2 Conformance requirements 45g36.3.3.2.3 Method of test 45g36.

26、3.3.2.4 Test procedure . 45g36.3.3.2.5 Test requirement 46g36.4 Equipment identity . 46g36.4.1 Purpose . 46g36.4.2 Conformance requirements . 46g36.4.3 Method of test . 46g36.4.4 Test procedure 46g36.4.5 Test requirements 46g37 Requirements for NGSO AES transmitting in the band 1 980 MHz to 2 010 MH

27、z 47g37.0 General . 47g37.1 Unwanted emissions limits outside the band 1 980,1 MHz to 2 009,9 MHz (carrier-on) 47g37.1.1 Purpose . 47g37.1.2 Conformance requirements . 47g37.1.3 Method of test . 48g37.1.4 Peak measurement 48g37.1.5 Average measurement . 48g37.1.6 Test requirements 49g37.2 Unwanted e

28、missions limits within the bands 1 980,1 MHz to 2 009,9 MHz, 1 978,1 MHz to 1 980,1 MHz and 2 009,9 MHz to 2 011,9 MHz (carrier-on). 49g37.2.1 Purpose . 49g37.2.2 Conformance requirements . 49g37.2.3 Method of test . 50g37.2.4 Measurement method 50g37.2.5 Test requirements 51g37.3 Unwanted emissions

29、 limits (carrier-off) . 51g37.3.1 Purpose . 51g37.3.2 Conformance requirements . 51g37.3.3 Method of test . 51g37.3.4 Peak measurement 52g37.3.5 Average measurement . 52g37.3.6 Test requirements 52g37.4 AES Control and Monitoring Functions (CMF) . 52g37.4.1 Special test equipment 52g37.4.2 Self-moni

30、toring functions . 53g37.4.2.1 Processor monitoring 53g37.4.2.1.1 Purpose 53g37.4.2.1.2 Conformance requirements 53g37.4.2.1.3 Method of test 53g37.4.2.2 Transmit frequency generation sub-system monitoring 53g37.4.2.2.1 Purpose 53g37.4.2.2.2 Conformance requirements 53g37.4.2.2.3 Method of test 53g3

31、7.4.3 Network control authorization and reception 53g37.4.3.1 Network control authorization 53g37.4.3.1.1 Purpose 53g3ETSI ETSI EN 301 473 V2.1.2 (2016-11) 6 7.4.3.1.2 Conformance requirements 54g37.4.3.1.3 Method of test 54g37.4.3.1.4 Test procedure . 54g37.4.3.1.5 Test requirement 54g37.4.3.2 Netw

32、ork control reception . 55g37.4.3.2.1 Transmit frequency control . 55g37.5 Equipment identity . 55g37.5.1 Purpose . 55g37.5.2 Conformance requirements . 56g37.5.3 Method of test . 56g37.5.4 Test procedure 56g37.5.5 Test requirements 56g38 Protection of the global navigation satellite service operati

33、ng in the band 1 559 MHz to 1 610 MHz 56g38.1 1 559 MHz to 1 605 MHz 56g38.1.1 Purpose . 56g38.1.2 Conformance requirements . 56g38.2 1 605 MHz to 1 610 MHz 57g38.2.1 Purpose . 57g38.2.2 Conformance requirements . 57g38.3 Method of test . 57g38.4 Average measurement 58g38.5 Test requirements . 58g39

34、 Protection of the radio astronomy services operating in the band 1 610,6 MHz to 1 613,8 MHz and in the band 1 660 MHz to 1 670 MHz . 58g39.1 Purpose . 58g39.2 Conformance requirements 58g39.2.1 Alternative 1 . 58g39.2.2 Alternative 2 . 59g39.2.3 Protection of the radio astronomy service in the 1 66

35、0,0 MHz to 1 670,0 MHz band 59g39.3 Method of test - unwanted emissions (alternative 1) 60g39.4 Test procedure - unwanted emissions (alternative 1) . 60g39.5 Test requirement - unwanted emissions (alternative 1) 60g39.6 Method of test - CMF function (alternative 2) . 61g39.7 Test procedure- CMF func

36、tion (alternative 2) 61g39.8 Test requirement- CMF function (alternative 2) 61g310 Requirements for GSO AES transmitting in the band 1 980 MHz to 2 010 MHz . 61g310.0 General . 61g310.1 Unwanted emissions limits outside the band 1 980 MHz to 2 010 MHz (carrier-on) 62g310.1.1 Purpose . 62g310.1.2 Con

37、formance requirements . 62g310.1.3 Method of test . 62g310.1.4 Peak measurement 63g310.1.5 Average measurement . 63g310.1.6 Test requirements 63g310.2 Unwanted emissions limits within the bands 1 980 MHz to 2 010 MHz, 1 978,1 MHz to 1 980 MHz and 2 010 MHz to 2 011,9 MHz (carrier-on) 64g310.2.1 Purp

38、ose . 64g310.2.2 Conformance requirements . 64g310.2.3 Method of test . 64g310.2.4 Measurement method 65g310.2.5 Test requirements 65g310.3 Unwanted emissions limits (carrier-off) . 65g310.3.1 Purpose . 65g310.3.2 Conformance requirements . 65g310.3.3 Method of test . 66g310.3.4 Peak measurement 66g

39、310.3.5 Average measurement . 66g310.3.6 Test requirements 67g310.4 AES Control and Monitoring Functions (CMF) . 67g3ETSI ETSI EN 301 473 V2.1.2 (2016-11) 7 10.4.1 Special test equipment 67g310.4.2 Self-monitoring functions . 67g310.4.2.1 Processor monitoring 67g310.4.2.1.1 Purpose 67g310.4.2.1.2 Co

40、nformance requirements 67g310.4.2.1.3 Method of test 67g310.4.2.2 Transmit frequency generation sub-system monitoring 68g310.4.2.2.1 Purpose 68g310.4.2.2.2 Conformance requirements 68g310.4.2.2.3 Method of test 68g310.4.3 Network control authorization and reception 68g310.4.3.1 Network control autho

41、rization 68g310.4.3.1.1 Purpose 68g310.4.3.1.2 Conformance requirements 68g310.4.3.1.3 Method of test 68g310.4.3.1.4 Test procedure . 68g310.4.3.1.5 Test requirement 69g310.4.3.2 Network control reception . 69g310.4.3.2.1 Transmit frequency control . 69g310.5 Equipment identity . 70g310.5.1 Purpose

42、. 70g310.5.2 Conformance requirements . 70g310.5.3 Method of test . 70g310.5.4 Test procedure 70g310.5.5 Test requirements 71g311 Receiver Performance Requirements . 71g311.1 General . 71g311.2 Receiver Adjacent Channel Selectivity 71g311.2.1 Purpose . 71g311.2.2 Conformance requirements . 71g311.2.

43、3 Conformance test 71g311.3 Receiver Blocking Characteristics . 71g311.3.1 Purpose . 71g311.3.2 Conformance requirements . 72g311.3.3 Conformance test 72g311.4 Method of testing . 72g311.4.1 Receiver Adjacent Channel Selectivity. 72g311.4.1.1 General 72g311.4.1.2 Test arrangement . 72g311.4.1.3 Test

44、 procedures . 73g311.4.2 Receiver Blocking Characteristics 73g311.4.2.1 General 73g311.4.2.2 Test arrangement . 73g311.4.2.3 Test procedures . 73g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 74g3Annex B (normative): General

45、test requirements . 76g3B.1 AES test modes 76g3B.2 Special Test Equipment 76g3B.2.1 STE description 76g3B.2.2 Use of STE for control and monitoring functions tests 77g3B.2.3 Test modulating signal . 77g3B.3 Laboratory Test Equipment 77g3B.4 Interpretation of the measurement results 78g3B.5 Test repo

46、rt 78g3ETSI ETSI EN 301 473 V2.1.2 (2016-11) 8 Annex C (normative): Environmental conditions . 79g3C.1 General . 79g3C.2 Environmental conformance requirements. 79g3C.3 Environmental test conditions 79g3Annex D (normative): Arrangements for measurement of emissions from AES . 80g3D.1 General . 80g3D

47、.2 Carrier-on emissions. 80g3D.2.1 Equipment required 80g3D.2.2 Equipment arrangement . 81g3D.2.3 Emissions from 4 GHz to 18 GHz 81g3D.2.4 Emissions from 10 kHz to 4 GHz . 81g3D.3 Carrier-off emissions 82g3D.3.1 Equipment required 82g3D.3.2 Equipment arrangement . 82g3D.3.3 Carrier-off emissions fro

48、m 4 GHz to 18 GHz 82g3D.3.4 Carrier-off emissions from 10 kHz to 4 GHz . 83g3Annex E (informative): Explanation of nominated bandwidth 84g3E.1 Introduction 84g3E.2 Interpretation of Parameters Bn, fc, a, b . 84g3E.3 Choice of nominated bandwidth . 84g3E.4 Maximum value for nominated bandwidth 86g3An

49、nex F (informative): Bibliography . 88g3History 89g3ETSI ETSI EN 301 473 V2.1.2 (2016-11) 9 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ET