ETSI EN 301 489-15-2016 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 15 Specific conditions for commercially available amateur radio equipment_1.pdf

1、 ETSI EN 301 489-15 V2.1.1 (2016-11) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 15: Specific conditions for commercially available amateur radio equipment; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU H

2、ARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)2 Reference REN/ERM-EMC-344 Keywords amateur, EMC, harmonised standard, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C A

3、ssociation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

4、print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kep

5、t on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.as

6、px If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

7、 and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. Al

8、l rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered

9、 and owned by the GSM Association. ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Defi

10、nitions 7g33.2 Symbols 7g33.3 Abbreviations . 7g34 Test conditions . 8g34.0 Introduction 8g34.1 General . 8g34.2 Arrangements for test signals . 8g34.2.0 Introduction. 8g34.2.1 Arrangements for test signals at the input of transmitters . 8g34.2.2 Arrangements for test signals at the output of transm

11、itters . 9g34.2.3 Arrangements for test signals at the input of receivers . 9g34.2.4 Arrangements for test signals at the output of receivers . 9g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 9g34.3 RF exclusion band of radio communications equipment 9g34.3.0 Genera

12、l 9g34.3.1 Exclusion band for receivers or the receiver part of transceivers . 9g34.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 10g34.3.2.1 Exclusion band for EMC emission measurements 10g34.3.2.2 Exclusion band for immunity tests 10g34.4 Narrowband responses of rece

13、ivers or receivers which are part of transceivers 10g34.5 Normal test modulation 11g34.5.1 Transmitters 11g34.5.2 Receivers 11g34.5.3 RF amplifiers and transverters 12g35 Performance assessment . 12g35.1 General . 12g35.2 Equipment which can provide a continuous communications link 12g35.3 Equipment

14、 which does not provide a continuous communications link . 12g35.4 Ancillary equipment . 12g35.5 Equipment classification 13g36 Performance criteria . 13g36.0 Introduction 13g36.1 Performance criteria for primary user functions . 14g36.1.0 Introduction. 14g36.1.1 General performance criteria (primar

15、y user functions) . 14g36.1.2 Performance criteria A for continuous phenomena (primary user functions) . 14g36.1.3 Performance criteria B for transient phenomena and short voltage dips (primary user functions) . 15g36.1.4 Performance criteria C for long voltage dips and interruptions (primary user f

16、unctions). 15g36.2 Performance criteria for secondary user functions . 16g36.3 Performance criteria for equipment which does not provide a continuous communication link 16g36.4 Performance criteria for ancillary equipment tested on a stand alone basis . 16g37 Applicability overview tables . 17g37.1

17、EMC Emission . 17g37.1.1 General 17g3ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)4 7.1.2 Special conditions . 17g37.2 Immunity 17g37.2.1 General 17g37.2.2 Special conditions . 18g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 19g3

18、Annex B (informative): Examples of amateur radio equipment within the scope of the present document . 21g3B.1 Amateur radio equipment which is commercially available 21g3History 22g3ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)5 Intellectual Property Rights IPRs essential or potentially essential to the

19、present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI i

20、n respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existen

21、ce of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spe

22、ctrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the ma

23、king available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of

24、 the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 15 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transpos

25、ition dates Date of adoption of this EN: 21 July 2016 Date of latest announcement of this EN (doa): 31 October 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 April 2017 Date of withdrawal of any conflicting National Standard (dow): 30 April 2018 Modal

26、verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT

27、 allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)6 1 Scope The present document, together with ETSI EN 301 489-1 1, covers the assessment of commercially available amateur radio equipment, and associated ancillary equipment, in respect of Ele

28、ctroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of commercially available amateur radio equipment are not included in the present document. Such technical specifications are found in the relevant product standard ETSI EN 30

29、1 783 i.2 for the effective use of the radio spectrum. The present document specifies the applicable EMC tests, the methods of measurement, the limits and the performance criteria for radio equipment intended for use by radio amateurs within the meaning of article 1, definition 53 of the Radio Regul

30、ations i.3 and associated ancillary equipment, which is commercially available. Examples of amateur radio equipment covered by the present document are given in annex B. The provisions of the present document apply to amateur radio equipment manufactured commercially either as ready-to-use equipment

31、, modules, or components having an intrinsic functionality for the customer. The expression “amateur radio equipment“ in the context of the present document is taken to mean “commercially available amateur radio equipment“ only. In case of differences (for instance concerning special conditions, def

32、initions, abbreviations) between the present document and ETSI EN 301 489-1 1, the provisions of the present document take precedence. The environment classification and the emission and immunity requirements used in the present document are as stated in ETSI EN 301 489-1 1, except for any special c

33、onditions included in the present document. The applicable environments referred to in ETSI EN 301 489-1 1 where equipment covered by the scope of the present document may be used, are to be declared by the manufacturer. 2 References 2.1 Normative references References are either specific (identifie

34、d by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be pu

35、blicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the applicatio

36、n of the present document. 1 ETSI EN 301 489-1 (V2.1.1) (11-2016): “ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essentia

37、l requirements of article 6 of Directive 2014/30/EU“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the lates

38、t version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)7 The following referenced documents are not nece

39、ssary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the m

40、arket of radio equipment and repealing Directive 1999/5/EC. i.2 ETSI EN 301 783: “Commercially available amateur radio equipment; Harmonised standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. i.3 ITU Radio Regulations. i.4 Commission Implementing Decision C(201

41、5) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions,

42、 symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 1, clause 3 and the following apply: maximum usable sensitivity: minimum receiver Radio Frequency (RF) input signal level or field strength able to produce a spec

43、ified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output performance which depends on this input signal level multimode equipment: amateur radio equipment capable of being used in several modes of operation, such as AM, FM, SSB 3.2 Symbols For the purposes of the present docume

44、nt, the symbols given in ETSI EN 301 489-1 1, clause 3 and the following apply: Fb skirt bandwidth Fc centre frequency of the transmitter necessary bandwidth Fn necessary bandwidth 3.3 Abbreviations For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1 1, clause 3 an

45、d the following apply: AM Amplitude Modulation BER Bit Error Ratio DSB-SC Double SideBand Suppressed Carrier EMC ElectroMagnetic Compatibility ESD ElectroStatic Discharge EUT Equipment Under Test FM Frequency ModulationHF High Frequency PEP Peak Envelope Power RF Radio Frequency SINAD Ratio of (Sign

46、al + Noise + Distortion) to (Noise + Distortion) SSB Single SideBand UHF Ultra High Frequency VHF Very High Frequency ETSI ETSI EN 301 489-15 V2.1.1 (2016-11)8 4 Test conditions 4.0 Introduction For the purposes of the present document, the test conditions of ETSI EN 301 489-1 1, clause 4, shall app

47、ly as appropriate. Further product related test conditions for amateur radio and ancillary equipment are specified in the present document. 4.1 General For emission and immunity tests, the test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5, shall apply

48、. The general test conditions for amateur radio equipment are as follows: - transmitters and amplifiers shall be tested in stand-by (if applicable) and in transmit mode of operation; - transceivers and transverters shall be tested in receive, stand-by, and transmit mode of operation; - if integral a

49、ntenna equipment provides an internal antenna connector for testing purposes, then the tests can be made via that connector. The manufacturer shall recommend a power supply (e.g. an AC/DC power adapter) for use in conjunction with the equipment under test (EUT), to ensure satisfactory operation of the combination during the EMC tests. When a range of different types of power supply units can be used with several types of that manufacturers radio equipment, then each type of power supply unit shall be tested with the radio providing the hi