ETSI EN 301 489-17-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment Part 17 Specific conditions .pdf

1、 ETSI EN 301 489-17 V2.2.1 (2012-09) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems Harmonized European Standard ETSI ETSI EN 301 489-17 V2.2.1 (201

2、2-09)2Reference REN/ERM-EMC-311 Keywords EMC, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important no

3、tice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portab

4、le Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information

5、on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may

6、be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2012. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for th

7、e benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 489-17 V2.2.1 (2012-09)3Contents Intellectual Propert

8、y Rights 5g3Foreword . 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 8g34 Test conditions . 8g34.1 General . 8g34.2 Arrangements for test signals . 8g34.2.1 Arrange

9、ments for test signals at the input of transmitters . 8g34.2.2 Arrangements for test signals at the output of transmitters . 8g34.2.3 Arrangements for test signals at the input of receivers . 9g34.2.4 Arrangements for test signals at the output of receivers . 9g34.2.5 Arrangements for testing transm

10、itter and receiver together (as a system) 9g34.3 Exclusion bands 9g34.4 Narrow band responses on receivers or receivers which are part of transceivers . 10g34.5 Normal test modulation 10g35 Performance assessment . 10g35.1 General . 10g35.2 Arrangements for the assessment of host dependant equipment

11、 and plug-in cards 10g35.2.1 Alternative A: composite equipment 10g35.2.2 Alternative B: use of a test jig or host . 11g35.3 Assessment procedures . 11g35.4 Ancillary equipment . 11g35.5 Equipment classification 11g36 Performance criteria . 11g36.1 General performance criteria 11g36.2 Performance ta

12、ble . 12g36.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) 12g36.4 Performance criteria for Transient phenomena applied to Transmitters (TT) 12g36.5 Performance criteria for Continuous phenomena applied to Receivers (CR) . 13g36.6 Performance criteria for Transient phen

13、omena applied to Receivers (TR) 13g37 Applicability overview . 13g37.1 Emission . 13g37.1.1 General 13g37.1.2 Special conditions . 13g37.2 Immunity 13g37.2.1 General 13g37.2.2 Special conditions . 13g3Annex A (informative): Examples of radio equipment in the scope of the present document 14g3A.1 Dat

14、a transmission systems operating in the 2,4 GHz ISM band and using wide band modulation techniques . 14g3A.2 5 GHz high performance RLAN systems . 14g3A.3 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz 14g3ETSI ETSI EN 301 489-17 V2.2.1 (2012-09)4A.4 Broadband data

15、transmitting/BWA Terminal Stations . 14g3A.5 Multi-Gigabit Wireless Systems (MGWS) 14g3Annex B (informative): Bibliography . 15g3History 16g3ETSI ETSI EN 301 489-17 V2.2.1 (2012-09)5Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to

16、 ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is ava

17、ilable from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 0

18、00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document ha

19、s been produced by ETSI in response to a mandate from the European Commission issued under Directive 98/34/EC i.2 as amended by Directive 98/48 i.12. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles

20、 and references of Harmonized Standard under the Directive 1999/5/EC i.1. See article 5.1 of Directive 1999/5/EC i.1 for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The p

21、resent document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 14 August 2012 Date of latest announcement of this EN (doa): 30 November 2012 Date of latest publication of new National Stand

22、ard or endorsement of this EN (dop/e): 31 May 2013 Date of withdrawal of any conflicting National Standard (dow): 31 May 2014 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications term

23、inal equipment within the scope of the R ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist

24、the user with regard to a particular subject area. i.1 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R 5 GHz high performance RLAN; Harmonized EN covering

25、the essential requirements of article 3.2 of the R 5,8 GHz fixed broadband data transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the R Part 2: TDD User Equipment Stations; Harmonized EN covering the essential requirements of article 3.2 of the R 60 GHz Multip

26、le-Gigabit WAS/RLAN Systems; Harmonized EN covering the essential requirements of article 3.2 of the R Mobile Terminal Stations; Harmonized EN covering the essential requirements of article 3.2 of the R Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and

27、using wide band modulation techniques; Harmonized EN covering the essential requirements of article 3.2 of the R A guide to the production of Harmonized Standards for application under the R Harmonized EN covering the essential requirements of article 3.2 of the R Part 19: OFDMA TDD WMAN (Mobile WiM

28、AX) TDD User Equipment (UE)“. i.11 ETSI EN 301 908-21: “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 21: OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)“. i.12 Directive 98/48/EC of the European Parliament and of the Council of 20 July 1

29、998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in EN 301 489-1 1 and the following

30、apply: Equipment Under Test (EUT): equipment under test and subject to the performance requirements of the present document fixed station: equipment intended for use in a fixed location and fitted with one or more antennas NOTE: The equipment may be fitted with either antenna socket(s) or integral a

31、ntenna(s) or both. hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both. host: any equipment which has

32、complete user functionality when not connected to the radio equipment part and to which the radio equipment part provides additional functionality and to which connection is necessary for the radio equipment part to offer functionality plug-in radio device: equipment, including slide-in radio cards,

33、 intended to be used with or within a variety of host systems, using their control functions and power supply stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally used on a stand-alone basis ETSI ETSI EN 301 489-17 V2.2.1 (2012-09)83.2 Ab

34、breviations For the purposes of the present document, the following abbreviations apply: ACK ACKnowledgement ARQ Automatic Retransmission reQuest BRAN Broadband Radio Access Networks BWA Broadband Wireless Access CR Continuous phenomena applied to Receivers CT Continuous phenomena applied to Transmi

35、tters EMC ElectroMagnetic Compatibility ERM Electromagnetic compatibility and Radio Matters EUT Equipment Under Test HIPERLAN HIgh PErformance Radio Local Area Network ISM Industrial, Scientific and Medical MGWS Multi-Gigabit Wireless SystemsMUS Maximum Usable Sensitivity NACK Not ACKnowledgement RF

36、 Radio Frequency RLAN Radio Local Area Network TR Transient phenomena applied to Receivers TT Transient phenomena applied to Transmitters 4 Test conditions 4.1 General For the purposes of the present document, the test conditions of EN 301 489-1 1, clause 4, shall apply as appropriate. Further produ

37、ct related test conditions for wideband data communications systems are specified in clauses 4.2 to 4.5. The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires connection to a host equipment to function shall use the test configuration as

38、 defined by the manufacturer. In all cases the EUT shall be exercised in a manner representative of normal intended use. 4.2 Arrangements for test signals The provisions of EN 301 489-1 1, clause 4.2 shall apply. 4.2.1 Arrangements for test signals at the input of transmitters The provisions of EN 3

39、01 489-1 1, clause 4.2.1 shall apply with the following modifications. The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer. The transmitter shall be operated at maximum rated power. 4.2.2 Arrangements for test signals at the output of t

40、ransmitters The provisions of EN 301 489-1 1, clause 4.2.2 shall apply with the following modifications. The manufacturer may provide a suitable companion receiver that can be used to receive messages or to set up a communication link. ETSI ETSI EN 301 489-17 V2.2.1 (2012-09)94.2.3 Arrangements for

41、test signals at the input of receivers The provisions of EN 301 489-1 1, clause 4.2.3 shall apply with the following modifications. The wanted signals required to establish a communications link shall be defined by the manufacturer. The level of the wanted signal at the input of the receiver shall b

42、e at least 30 dB above the declared Maximum Usable Sensitivity (MUS). 4.2.4 Arrangements for test signals at the output of receivers The measuring equipment for the output signal from the receiver under test shall be located outside the test environment. It shall be possible to assess the performanc

43、e of the equipment by appropriately monitoring the receiver output. If the receiver has an output connector or port providing the wanted output signal, then this port shall be used via a cable, consistent with the standard cable used in normal operation, connected to the external measuring equipment

44、 outside the test environment. The measuring equipment may be supplied by the manufacturer. Precautions shall be taken to ensure that any effect on the test due to the coupling means is minimized. The manufacturer may provide a suitable companion transmitter that can be used to transmit messages or

45、to set up a communication link. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of EN 301 489-1 1, clause 4.2.5 shall apply. The manufacturer may provide a suitable companion transceiver or transmitter and receiver that can be used to send and receive me

46、ssages or to set up a communication link. Both the EUT and the companion equipment shall transmit the normal test modulation. Further, the output of the radio equipment under test shall be monitored by the test system. 4.3 Exclusion bands The frequencies on which the transmitter part of the EUT is i

47、ntended to operate shall be excluded from radiated emission measurements when performed in transmit mode of operation. There shall be no frequency exclusion band applied to emission measurements of the receiver part of transceivers or the stand alone receiver under test, and/or associated ancillary

48、equipment. The exclusion band for immunity testing shall be calculated as follows: lower limit of exclusion band = lowest allocated band edge frequency -5 %; upper limit of exclusion band = highest allocated band edge frequency +5 %. Using the 2,450 MHz band as an example: lower limit of exclusion b

49、and = 2 400 - 120 = 2 280 MHz; upper limit of exclusion band = 2 483,5 + 124,175 = 2 607,675 MHz; thus the exclusion band for 2,45 GHz equipment falling within the scope of the present document extends from 2 280 MHz to 2 607,675 MHz. ETSI ETSI EN 301 489-17 V2.2.1 (2012-09)104.4 Narrow band responses on receivers or receivers which are part of transceivers The provision of EN 301 489-1 1, clause 4.4 shall apply. 4.5 Normal test modulation The modulated test signal shall represent normal intended use, and may contain data formatting, e