ETSI EN 301 489-20-2002 Electromagnetic Compatibility and Radio Spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services Part 20 Specifi_1.pdf

1、ETSI EN 301 489-20 1.2.1 (2002-11) Candida fe Harmonized European Sfandard (Telecommunicafions series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMag net ic Com pati bi I ity (EM C) standard for radio equipment and services; Part 20: Specific conditions for Mobile Earth S

2、tations (MES) used in the Mobile Satellite Services (MSS) 2 ETSI EN 301 489-20 VI .2.1 (2002-1 1) Reference REN/ERM-EMC-230-20 Keywords earth station, EMC, MSS, radio, regulation, satellite, testing ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33

3、4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:lwmv.etsi .arq The present document may be made available in more than one

4、electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive

5、 within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors in the p

6、resent document, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2002. All rights reserved. DECTTM,

7、 PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizati

8、onal Partners. ETSI 3 ETSI EN 301 489-20 VI . 2.1 (2002-1 1) Contents Intellectual Property Rights 4 Foreword . 4 1 2 3 3.1 3.2 4 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.3 4.3.1 4.3.2 4.4 5 5.1 5.2 5.2.1 5.2.2 5.3 5.4 6 6.1 6.2 6.3 7 7.1 7.1.1 7.1.2 7.2 7.2.1 7.2.2 Scope 5 References 5 Definitions a

9、nd abbreviations . 6 Definitions 6 Abbreviations . 6 Test conditions . 7 7 7 8 8 9 9 Arrangements for testing transmitter and receiver together (as a system) 9 Exclusion bands 9 Transmitter exclusion band . 9 Receiver exclusion band . 9 Narrow band responses of receivers . 9 Performance assessment .

10、 10 General . 10 MES connected to host equipment . 10 Alternative A: combined equipment . 10 10 Arrangements for test signals at the input of transmitters Arrangements for test signals at the output of transmitter Arrangements for test signals at the input of receivers Arrangements for test signals

11、at the output of receiver Alternative B: use of a test jig Ancillary equipment 10 Equipment classifica 11 Performance criteria . 11 General . 11 Performance criteria for Continuous Phenomena (CP) 11 Performance criteria for Transient Phenomena (TP) 12 Applicability overview . 12 Emission . 12 Genera

12、l 12 Special conditions . 12 General 12 Special conditions . 12 Immunity 12 Annex A (normative): A . 1 A.2 A.3 A.4 A.5 Definitions of MESS within the scope of the present document . 13 MESs operating within 1. 6 GHz/2. 4 GHz band . 13 MESs operating within the 1. 5 GHz/l. 6 GHz 13 MESs operating wit

13、hin 2. O GHz band 13 MESs operating below 1 GHz 14 MESs operating in the 11 GHz/l2 GHz/l4 GHz frequency bands 14 Annex B (informative): Bibliography . 15 History 16 ETSI 4 ETSI EN 301 489-20 VI .2.1 (2002-1 1) Intellectual Property Rights IPRs essential or potentially essential to the present docume

14、nt may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 3 14: “Intellectual Property Rights (7PRs); Essential, orpotentially Essential, IPRs notlJied to ETSI in respect ofET

15、SI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (htttwp :l;webawpiwi .c tsi .ordIPR/honie. am). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to th

16、e existence of other IPRs not referenced in ETSI SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee

17、Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of technical

18、 standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Council Directive on the approximation of the laws of the Member States relating to electromagnet

19、ic compatibility (“the EMC Directive“) (89/336/EEC 3 as amended) and Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R ElectroMagnetic Compatibility (EM

20、C) standard for radio equipment and services; Part 1 : Common technical requirements“. Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R a specific Quality o

21、f Transmission Measurement Apparatus (QTMA). b) EXAMPLE: The quality of transmission can concern: - the audio signal; - the BER; - the message throughput; - the continuity of the communication link; or - a combination of them. For the immunity tests of the EUT, a communications link shall be establi

22、shed between the EUT and the testing system. The EUT shall be placed in the operating mode. For EUT for which connection to a host equipment is necessary to offer functionality the manufacturer shall select which of the alternative performance assessment configurations shall be used. ETSI 8 ETSI EN

23、301 489-20 VI .2.1 (2002-1 1) 4.2.1 Arrangements for test signals at the input of transmitters The provisions of EN 301 489-1 i, clause 4.2.1 shall apply. 4.2.2 Arrangements for test signals at the output of transmitters The provisions of EN 301 489-1 i, clause 4.2.2 shall apply with the following m

24、odifications. For transmitters, the EUT shall be operated at its maximum rated RF output Peak Envelope Power (PEP), or at a level not less than -6 dB relative to that power level in the event of declared thermal limitations. The transmitter shall be modulated with a test signal which represents norm

25、al operation as specified by the manufacturer. A communication link shall be established at the start of the test and be maintained throughout the test. A suggested test configuration is shown in figure 1. .l.l.l.l.l.l.l.l.l.l.l.l.l.l.l.l.l.l.l.l . . . . . . . . . . . . . . . . . . . . . . . . . . .

26、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OR Figure 1: Suggested test configuration ETSI 9 ETSI EN 301 489-20 VI .2.1 (2002-1 1) 4.2.3 Arrangements for test signals at the input of receivers The provisions of EN 301 489-1 i, clause 4.2.3 shall apply with the followin

27、g modifications. For the immunity tests of receivers, the wanted input signal, coupled to the receiver, shall be modulated with a test signal specified by the manufacturer which represents normal operation. For the measurement of the quality of transmission, a communications link shall be establishe

28、d and the wanted input signal shall be applied to the Radio Frequency (RF) input of the receiver. Signal level adjustment may be performed by adjustment of the test transmitter output level such that the received signal level is as close to the normal operation signal level as possible. The Special

29、Test Equipment (STE), the QTMA and the source of the wanted input signal shall be located outside the test environment. 4.2.4 Arrangements for test signals at the output of receivers The provisions of EN 301 489-1 i, clause 4.2.4 shall apply with the following modifications. For the quality of trans

30、mission measurements the MES may be put in a specific mode of operation where the received data are looped back to the modulation input of the transmitter part of the EUT. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of EN 301 489-1 i, clause 4.2.5 sh

31、all apply. 4.3 Exclusion bands The provision of EN 301 489-1 i, clause 4.3 shall apply with the following modifications: - - the transmitter exclusion band and the receiver exclusion band as defined below shall apply, there shall be no exclusion bands for the ancillary equipment. 4.3.1 Transmitter e

32、xclusion band The transmitter exclusion band is the band of frequencies over which no tests of radiated immunity of a transmitter are made. The lower frequency of the transmitter exclusion band is the centre frequency minus twice the occupied bandwidth. The upper frequency of the transmitter exclusi

33、on band is the centre frequency plus twice the occupied bandwidth. 4.3.2 Receiver exclusion band The receiver exclusion band is the band of frequencies over which no tests of radiated immunity of a receiver are made. The lower frequency of the receiver exclusion band is the lower frequency of the co

34、mplete receive band of the EUT minus 5 % of that lower frequency. The upper frequency of the receiver exclusion band is the upper frequency of the complete receive band of the EUT plus 5 % of that upper frequency. 4.4 Narrow band responses of receivers The provisions of EN 301 489-1 i, clause 4.4 sh

35、all not apply. ETSI 10 ETSI EN 301 489-20 VI .2.1 (2002-1 1) 5 Performance assessment 5.1 Gen eral The provision of EN 301 489-1 i, clause 5.1 shall apply with the following modification. In addition, the manufacturer shall, at the time of submission of the equipment for test, declare comprehensivel

36、y the intended use of the equipment, and provide full and complete documentation necessary for user operation, testing and evaluation purposes. The present documentation shall include, but need not be limited to: - the ranges of the operational parameters, e.g. the power delivered to the antenna, th

37、e frequency ranges, the operational frequencies; the ancillary equipment andor host equipment to be combined with the MES for testing, if applicable; the user-control functions that are required for normal operation; the method and criteria to be used to assess the quality of transmission. - - - Thi

38、s information shall be in accordance with the documentation and the information leaflet accompanying the equipment and shall be recorded in the test report. 5.2 MES connected to host equipment For MES parts for which connection to or integration with a host equipment is necessary in order to offer a

39、dditional functionality, two alternative approaches are permitted. The manufacturer shall declare which alternative shall be used. 5.2.1 Alternative A: combined equipment A combination of a MES and a specific type of host equipment is used for testing according to the present document. Where more th

40、an one such combination is intended, testing shall not be repeated for combinations of MES and other host equipment where the latter are substantially similar, in particular such that host models are unlikely to significantly influence the intrinsic immunity and unwanted emissions of the MES. Where

41、more than one such combination is intended and host equipment are not substantially similar, one combination shall be tested against all requirements of the present document; all other combinations shall be tested separately for emissions only. 5.2.2 Alternative B: use of a test jig Where the MES is

42、 intended for use with a variety of host equipment, the manufacturer shall supply a suitable test jig that is representative of the range of host equipment in which the device is intended to be used. The test jig shall allow the MES part to be powered and stimulated in a way similar to the way it wo

43、uld be powered and stimulated when connected to or inserted into the host equipment. Measurements shall be made to all requirements of the present document. The test jig shall be designed such that alteration of the MESS intrinsic immunity and unwanted emissions is minimized. 5.3 Anci Ilary equ i pm

44、ent The provision of EN 301 489-1 i, clause 5.4 shall apply. ETSI 11 ETSI EN 301 489-20 VI .2.1 (2002-1 1) 5.4 Equipment classification The provision of EN 301 489-1 i, clause 5.5 shall apply with the following modifications. The MES shall be classified in one or a combination of the following class

45、es: - vehicle mounted MES (V-MES) intended to be powered by the vehicle main battery, shall meet the requirements for mobile equipment; portable MES (P-MES) powered by a stand alone battery, shall meet the requirements for portable equipment; fixed MES (F-MES) powered either by a DC or AC mains, sha

46、ll meet the requirements for base station e quip men t. - - A V-MES is an Installable Equipment (IE); a P-MES is a Portable Equipment (PE). 6 Performance criteria 6.1 Gen eral The equipment shall meet the minimum performance criteria as specified in clauses 6.2 and 6.3 The establishment of a communi

47、cations link at the start of the test, the maintenance of the communications link and the assessment of the recovered signal information is used as the performance criteria to ensure that the essential functions of the EUT are evaluated during and after the test. 6.2 Performance criteria for Continu

48、ous Phenomena (CP) The following procedures shall apply: during each individual exposure in the test sequence it shall be verified by the QTMA supplied by the manufacturer that the communications link is maintained, and that the quality of transmission observed is no worse than that declared by the

49、manufacturer; at the conclusion of the test: - the EUT shall operate as intended with no loss of user control functions or stored data, as declared by the manufacturer; - - under no circumstances shall the transmitter operate unintentionally. the communications link has been maintained during the test; and the quality of transmission observed is no worse than that declared by the manufacturer; ETSI 12 ETSI EN 301 489-20 VI .2.1 (2002-1 1) Reference to clauses in EN 301 489-1 I 9.7.3 Performance criteria; Voltaae dim and interruDtions 6.3 Special product-r