ETSI EN 301 489-28-2004 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 28 Specifi.pdf

1、 ETSI EN 301 489-28 V1.1.1 (2004-09)Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC)standard for radio equipment and services;Part 28: Specific conditions for wireless digital video li

2、nksETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 2 Reference DEN/ERM-EMC-237-28 Keywords digital, EMC, radio, regulation, video ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucr

3、atif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference

4、 in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that th

5、e document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal

6、.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTES

7、TSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Pa

8、rtners. ETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 3 Contents Intellectual Property Rights4 Foreword.4 1 Scope 5 2 References 5 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .6 4 Test conditions .6 4.1 General .6 4.2 Arrangements for test signals .7 4.2.1 Arrangements for test s

9、ignals at the input of transmitters.7 4.2.2 Arrangements for test signals at the output of transmitters.7 4.2.3 Arrangements for test signals at the input of receivers .7 4.2.4 Arrangements for test signals at the output of receivers .8 4.2.5 Arrangements for testing transmitter and receiver togethe

10、r (as a system) 8 4.3 Exclusion bands8 4.3.1 Receiver and receivers of transceivers exclusion band.8 4.3.2 Transmitter exclusion band.8 4.4 Narrow band responses of receivers.9 5 Performance assessment.9 5.1 General .9 5.2 Equipment which can provide a continuous communications link 9 5.3 Equipment

11、which does not provide a continuous communications link.9 5.4 Ancillary equipment .9 5.5 Equipment classification 9 6 Performance criteria .10 6.1 General performance criteria10 6.2 Performance criteria for Continuous phenomena applied to Transmitters (CT) 10 6.3 Performance criteria for Transient p

12、henomena applied to Transmitters (TT)10 6.4 Performance criteria for Continuous phenomena applied to Receivers (CR).11 6.5 Performance criteria for Transient phenomena applied to Receivers (TR) 11 6.6 Performance criteria for ancillary equipment tested on a stand alone basis .11 7 Applicability over

13、view.12 7.1 Emission.12 7.1.1 General12 7.1.2 Special conditions.12 7.2 Immunity 12 7.2.1 General12 7.2.2 Special conditions.12 Annex A (normative): Examples of equipment covered by the present document13 Annex B (informative): Bibliography.14 Annex C (informative): The EN title in the official lang

14、uages .15 History 16 ETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-memb

15、ers, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.

16、asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the p

17、resent document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Co

18、mmission issued under Council Directive 98/34/EC 4 (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document together with EN 301 489-1 1 is intended to become a Harmonized Standard, the reference of which will be

19、published in the Official Journal of the European Communities referencing the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (“the EMC Directive“) (89/336/EEC 3 as amended) and Directive 1999/5/EC of the European Parliament and of th

20、e Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements“. 2 Directive 1999/5/EC of the European P

21、arliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R Wireless Video Links (WVL) operating in the 1,3 GHz to 50 GHz frequency band; Part 1: Technical characteristics and methods of measurement“. ETS

22、I ETSI EN 301 489-28 V1.1.1 (2004-09) 6 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in EN 301 489-1 1 and the following apply: integral antenna: antenna designed to be connected to the equipment without the use of a 50 ext

23、ernal connector and considered to be part of the equipment NOTE: An integral antenna may be fitted internally or externally to the equipment. quasi-error-free (DVB-T): defined as BER 2 10-4after Viterbi decoding, which virtually eliminates errors following the Reed-Solomon decode switching range: ma

24、ximum frequency range over which the receiver or transmitter can be operated without reprogramming or realignment 3.2 Abbreviations For the purpose of the present document, the following abbreviations apply: BER Bit Error Rate CHS CHannel Separation CR Continuous ReceiversCT Continuous Transmitters

25、DVB-T Digital Video Broadcast-Terrestrial EMC ElectroMagnetic Compatibility EUT Equipment Under Test IF Intermediate FrequencyLONM Loss Of Noise Margin QEF Quasi-Error-Free RF Radio Frequency TR Transient Receivers TT Transient Transmitters4 Test conditions For the purposes of the present document,

26、the test conditions of EN 301 489-1 1, clause 4 shall apply as appropriate. 4.1 General For emission and immunity tests the test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.4 shall apply. For the purpose of EMC tests, body worn or hand held transmitter

27、s shall be mounted on a non-conductive stand at least 0,8 m from any conducting surface. The EUT and any other equipment required for the performance assessment before, during, and after the conclusion of the tests, shall be connected in a manner typical of normal intended use. Whenever the EUT is p

28、rovided with a detachable antenna, it shall be tested with the antenna fitted in a manner typical of normal intended use. For immunity tests, if the equipment is of a category which permits it, a communications link shall be established at the start of the test and maintained during the test. The te

29、st conditions shall be as follows: the transmitter shall be operated at its normal maximum RF output power modulated with a suitable modulation signal (see clause 4.2.1); ETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 7 for stand alone receivers or receivers of transceivers operating in simplex mode, the

30、wanted RF input signal, coupled to the receiver, shall be modulated with a suitable modulation signal (see clause 4.2.3); for duplex transceivers, the wanted RF input signal, coupled to the receiver, shall be modulated with a suitable modulation signal (see clause 4.2.3). The transmitter shall be op

31、erated at its normal maximum output power, modulated with the test modulation signal, coupled to the transmitter from the output of the receiver (repeater mode). 4.2 Arrangements for test signals The provisions of EN 301 489-1 1, clause 4.2 shall apply. 4.2.1 Arrangements for test signals at the inp

32、ut of transmitters The provisions of EN 301 489-1 1, clause 4.2.1 shall apply with the following modifications. For the purpose of the present document, the transmitter video or combined video/audio input signal shall be supplied by a generator at the correct impedance applied at the connections of

33、the stated inputs, unless otherwise stated (see figures 1 and 2). The manufacturer shall specify a representative test signal. 4.2.2 Arrangements for test signals at the output of transmitters The provisions of EN 301 489-1 1, clause 4.2.2 shall apply. 4.2.3 Arrangements for test signals at the inpu

34、t of receivers The provisions of EN 301 489-1 1, clause 4.2.3 shall apply with the following modifications. For the purpose of the present document, the transmitter video or combined video/audio input signal shall be supplied by a generator at the correct impedance applied at the connections of the

35、stated inputs, unless otherwise stated (see figures 1 and 2). The manufacturer shall specify a representative test signal. Absorber Lined test chamber Generator EUT Interfering signal Wanted signal Receiver RF Input Output BER Test Equipment t Output Input Variable attenuator Figure 1: Test configur

36、ation for integral antenna; transmitter operation - electrical input ETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 8 Absorber Lined test chamber Generator EUT Interfering signal Wanted signal Transmitter RF Output Input BER Test Equipment Output Input Variable attenuator Figure 2: Test configuration for

37、integral antenna; receiver operation 4.2.4 Arrangements for test signals at the output of receivers The provisions of part 1 EN 301 489-1 1, clause 4.2.4 shall apply. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of EN 301 489-1 1, clause 4.2.5 shall a

38、pply. 4.3 Exclusion bands The provisions of EN 301 489-1 1, clause 4.3 shall apply. 4.3.1 Receiver and receivers of transceivers exclusion band The exclusion band for receivers and receivers of transceivers is the frequency range determined by the switching range, as declared by the manufacturer, ex

39、tended as follows: the lower frequency of the exclusion band is the lower frequency of the switching range, minus 5 % of the centre frequency of the switching range; the upper frequency of the exclusion band is the upper frequency of the switching range, plus 5 % of the centre frequency of the switc

40、hing range. 4.3.2 Transmitter exclusion band Exclusion bands shall not be applied when measuring transmitters in standby mode. For the purpose of the present document, the exclusion band shall extend over the frequencies above and below the fundamental transmitting frequency, but separated from the

41、centre frequency of the emission by 250 % of the relevant Channel Separation (CHS) of the radio-frequency channel arrangement where the system is to be placed. When the CHS is not defined the exclusion band shall extend over the frequencies above and below the fundamental transmitting frequency but

42、separated from the centre frequency of the emission by 250 % of the necessary bandwidth. ETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 9 4.4 Narrow band responses of receivers The provision of EN 301 489-1 1, clause 4.4 shall apply. The nominal frequency offset used for the identification of narrowband r

43、esponses shall be twice the bandwidth of the receiver IF filter immediately preceding the demodulator, as declared by the manufacturer, for the first part of the identification procedure, and two and one half times the bandwidth of the receiver for its second part. The narrowband response shall be l

44、imited to less than 3 times the declared channel bandwidth (B) of the system. See EN 302 064-1 5. 5 Performance assessment 5.1 General The provision of EN 301 489-1 1, clause 5.1 shall apply with the following modification. In addition, the manufacturer shall at the time of submission of the equipme

45、nt for test, supply the following information to be recorded in the test report: the coupling means to be used for the application of the modulation signal to the EUT and for monitoring the output of the EUT; and the level and make up of the RF test signal for the establishment of the communications

46、 link; description of test fixtures. 5.2 Equipment which can provide a continuous communications link The provision of EN 301 489-1 1, clause 5.2 shall apply. 5.3 Equipment which does not provide a continuous communications link The provision of EN 301 489-1 1, clause 5.3 shall apply. 5.4 Ancillary

47、equipment The provision of EN 301 489-1 1, clause 5.4 shall apply. 5.5 Equipment classification The provision of EN 301 489-1 1, clause 5.5 shall apply. ETSI ETSI EN 301 489-28 V1.1.1 (2004-09) 106 Performance criteria 6.1 General performance criteria The equipment shall meet the performance criteri

48、a specified in this clause and clauses 6.2, 6.3, 6.4, 6.5 and 6.6 as appropriate. The establishment and maintenance of a communications link and the assessment of loss of noise margin at the Quasi-Error-Free (QEF) point are used as performance criteria to ensure that all primary functions of the tra

49、nsmitter and receiver are evaluated during the immunity tests. In addition, the test shall also be performed in idle mode to ensure the transmitter does not unintentionally operate. The maintenance of a communications link shall be assessed using an indicator which may be part of the test system or the EUT. If an equipment is of a specialized nature, such that the performance criteria described in the following clauses are not appropriate, then the manufacturer shall declare, for inclusion in the test report, his own sp