ETSI EN 301 489-51-2016 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 51 Specific conditions for Automotive Ground based Vehicles and Surveilla.pdf

1、 ETSI EN 301 489-51 V1.1.1 (2016-11) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 51: Specific conditions for Automotive, Ground based Vehicles and Surveillance Radar Devices using 24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81

2、 GHz; Harmonised Standard covering the essential requirements of article 3.1b of Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)2 Reference DEN/ERM-EMC-346 Keywords EMC, harmonised standard, measurement, radar ETSI 650 Route des Lucioles F-06921 Sophia Anti

3、polis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present d

4、ocument may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions a

5、nd/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current

6、 status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part

7、may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoin

8、g restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the bene

9、fit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Nor

10、mative references . 5g32.2 Informative references 6g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Test conditions . 6g34.1 General . 6g34.2 Arrangements for test signals . 6g34.2.1 General 6g34.2.2 Arrangements for test signals at the input of transmitters . 6g34.

11、2.3 Arrangements for test signals at the output of transmitters . 7g34.2.4 Arrangements for test signals at the input of receivers . 7g34.2.5 Arrangements for test signals at the output of receivers . 7g34.2.6 Arrangements for testing transmitter and receiver together (as a system) 7g34.3 Exclusion

12、bands 7g34.4 Narrow band responses of receivers . 7g34.5 Normal test modulation 7g35 Performance assessment . 7g35.1 General . 7g36 Performance criteria . 7g36.0 Introduction 7g36.1 Performance criteria . 8g37 Applicability overview . 8g37.1 Emission . 8g37.2 Immunity 8g3Annex A (normative): Relatio

13、nship between the present document and the essential requirements of Directive 2014/53/EU . 9g3History 11g3ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining

14、 to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat.

15、 Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the E

16、TSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commi

17、ssions standardisation request C(2015) 5376 final i.2 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 199

18、9/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the co

19、rresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 51 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 21 November 2016 Date of latest an

20、nouncement of this EN (doa): 28 February 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 August 2017 Date of withdrawal of any conflicting National Standard (dow): 31 August 2018 Modal verbs terminology In the present document “shall“, “shall not“, “sho

21、uld“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. E

22、TSI ETSI EN 301 489-51 V1.1.1 (2016-11)5 1 Scope The present document, together with ETSI EN 301 489-1 1, covers the assessment of automotive, ground based vehicles and surveillance radar devices using 24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77 GHz to 81 GHz in respect of

23、 ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of radar equipment are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio s

24、pectrum. The present document specifies the applicable test conditions, performance assessment and performance criteria for automotive and surveillance radar devices and associated ancillary equipment. Automotive and surveillance radar equipments are low power millimetre wave devices that are able t

25、o detect and characterize targets in their environment. The following use cases are included (but are not limited to): automotive Advanced Driver Assistance Systems (ADAS) applications, such as Adaptive Cruise Control (ACC), Blind Spot Detection (BSD), parking aid, backup aid, autonomous braking and

26、 pre-crash systems (PCS); surveillance radars for other kind of ground based vehicles, such as trains, trams, aircrafts while taxiing; fixed infrastructure radars for traffic monitoring; railway/road crossings obstacle detection radars; helicopter obstacle detection radars. Examples of automotive an

27、d surveillance radar devices are given in the related harmonised standards. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 489-1 1, the provisions of the present document take precedence. The environmental

28、classification and the emission and immunity requirements used in the present document are as stated in ETSI EN 301 489-1 1, except for any special conditions included in the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and

29、/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expe

30、cted location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1

31、 ETSI EN 301 489-1 (V2.1.1) (11-2016): “ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6

32、of Directive 2014/30/EU“. ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)6 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific referen

33、ces, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of

34、 the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and

35、 repealing Directive 1999/5/EC. i.2 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directiv

36、e 2014/53/EU of the European Parliament and of the Council. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in clause 3 of ETSI EN 301 489-1 1 apply. 3.2 Abbreviations For the purposes of the present document, the abbreviation

37、s given in clause 3 of ETSI EN 301 489-1 1 apply. 4 Test conditions 4.1 General For the purposes of the present document, the test conditions of ETSI EN 301 489-1 1, clause 4 shall apply as appropriate except as varied herein. For emission and immunity tests the test modulation, test arrangements, e

38、tc., as specified in the present document, clauses 4.2 to 4.5, shall apply. 4.2 Arrangements for test signals 4.2.1 General The provisions of ETSI EN 301 489-1 1, clause 4.2 shall apply. 4.2.2 Arrangements for test signals at the input of transmitters The provisions of ETSI EN 301 489-1 1, clause 4.

39、2.1 shall apply. ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)7 4.2.3 Arrangements for test signals at the output of transmitters The provisions of ETSI EN 301 489-1 1, clause 4.2.2 shall apply with the following modification. The transmitter shall be operated at its maximum rated RF output power, modula

40、ted with normal test modulation (see clause 4.5). Measurement equipment is not required. The signal shall be directed to a dummy target or a target simulator. 4.2.4 Arrangements for test signals at the input of receivers The provisions of ETSI EN 301 489-1 1, clause 4.2.3 shall apply with the follow

41、ing modification. The return signal shall be generated by either a dummy target or a target simulator. 4.2.5 Arrangements for test signals at the output of receivers The provisions of ETSI EN 301 489-1 1, clause 4.2.4 shall apply. 4.2.6 Arrangements for testing transmitter and receiver together (as

42、a system) The provisions of ETSI EN 301 489-1 1, clause 4.2.5 shall not apply. For the purpose of testing radar equipment the receiver and transmitter shall be tested as a system. 4.3 Exclusion bands No exclusion bands are applicable. 4.4 Narrow band responses of receivers The provisions of ETSI EN

43、301 489-1 1, clause 4.4 shall apply. 4.5 Normal test modulation The equipment shall be operated in a transmission mode representative of normal operation. 5 Performance assessment 5.1 General The provision of ETSI EN 301 489-1 1, clause 5 shall apply except as varied herein. The provision of ETSI EN

44、 301 489-1 1, clause 5.2 shall not apply. The manufacturer shall supply a list of operation modes of the EUT. 6 Performance criteria 6.0 Introduction For the purposes of the present document the provisions of ETSI EN 301 489-1 1, clause 6, shall not apply. ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)8 T

45、he performance criteria are used to make an assessment whether a radar equipment passes or fails immunity tests. 6.1 Performance criteria In table 1 below: Performance criterion A applies for immunity tests with phenomena of a continuous nature; Performance criterion B applies for immunity tests wit

46、h phenomena of a transient nature. Table 1: Performance Requirements Criterion During test After test A Operate as intended No loss of function No unintentional responses Operate as intended No loss of function No degradation of performance B No unintentional responses Operate as intended Lost funct

47、ion(s) shall be self-recoverable No degradation of performance Where “operate as intended“ or “no loss of function“ is specified, the EUT shall demonstrate correct functioning as described in clause 5. Where the EUT has more than one mode of operation (including stand-by) an unplanned transition fro

48、m one mode to another is an unintentional response. The EUT shall be tested in sufficient modes to confirm there are no such unintentional responses. 7 Applicability overview 7.1 Emission Table 1 in ETSI EN 301 489-1 1 contains the applicability of EMC emission measurements to the relevant ports of

49、radio and/or associated ancillary equipment. Details on the test conditions are specified in clause 4 of the present document. 7.2 Immunity Table 2 of ETSI EN 301 489-1 1 contains the applicability of EMC immunity measurements to the relevant ports of radio and/or associated ancillary equipment. Details on the test conditions are specified in clause 4 of the present document. ETSI ETSI EN 301 489-51 V1.1.1 (2016-11)9 Annex A (normative): Relationship between the present document and the essential requirements of D