ETSI EN 301 489-6-2016 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 6 Specific conditions for Digital Enhanced Cordless Telecommunications (DE_1.pdf

1、 ETSI EN 301 489-6 V2.1.1 (2016-11) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 6: Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive

2、 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 2 Reference REN/ERM-EMC-327 Keywords DECT, EMC, harmonised standard, radio, regulation ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 5

3、62 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of

4、any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Fo

5、rmat (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ET

6、SIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical,

7、including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standa

8、rds Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are

9、Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions and abbreviations

10、. 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Test conditions . 8g34.1 General . 8g34.2 Arrangements for test signals . 8g34.2.0 General 8g34.2.1 Arrangements for test signals at the input of transmitters . 8g34.2.1.1 Speech equipment . 8g34.2.1.2 Non-speech equipment 8g34.2.2 Arrangements for te

11、st signals at the output of transmitters . 8g34.2.3 Arrangements for test signals at the input of receivers . 9g34.2.4 Arrangements for test signals at the output of receivers . 9g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 9g34.3 RF exclusion band of radio commun

12、ications equipment 9g34.3.1 Introduction. 9g34.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 9g34.3.2.1 General 9g34.3.2.2 Channelized Systems 9g34.3.3 Exclusion band for receivers or the receiver part of transceivers . 9g34.4 Narrow band responses on receivers or rece

13、ivers which are part of transceivers . 10g34.5 Normal test modulation 10g35 Performance assessment . 10g35.1 General . 10g35.2 Arrangements for the assessment of host dependant equipment and plug-in cards 10g35.2.0 Two alternative approaches 10g35.2.1 Alternative A: composite equipment 11g35.2.2 Alt

14、ernative B: use of a test jig and three hosts 11g35.3 Assessment procedures . 11g35.3.1 Loss of user control functions or stored user defined data 11g35.3.2 Audio breakthrough 11g35.4 Ancillary equipment . 12g35.5 Equipment classification 13g36 Performance criteria . 13g36.1 General . 13g36.2 Perfor

15、mance criteria for Continuous phenomena of Transceivers (CT) . 13g36.3 Performance criteria for Transient phenomena applied to Transceivers (TT) 13g36.4 Performance criteria for Continuous phenomena applied to Receive-only equipment (CR) . 14g36.5 Performance criteria for Transient phenomena applied

16、 to Receive-only equipment (TR) . 14g36.6 Performance criteria for ancillary equipment tested on a standalone basis 14g37 Applicability overview . 14g37.1 Emission . 14g37.1.1 General 14g37.1.2 Special conditions . 14g37.2 Immunity 14g3ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 4 7.2.1 General 14g37.2.

17、2 Special conditions . 15g38 Methods of measurement and limits for EMC emissions 15g39 Test methods and levels for immunity tests . 15g39.1 Test configuration. 15g39.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) . 15g39.2.1 General 15g39.2.2 Test method 15g39.2.3 Performance criteria

18、 15g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 16g3Annex B (normative): Definitions of cordless telecommunications equipment in the scope of the present document . 18g3B.1 Digital Enhanced Cordless Telecommunications (DECT

19、) equipment . 18g3Annex C (informative): Bibliography . 19g3History 20g3ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, i

20、s publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on th

21、e ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may b

22、e, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(20

23、15) 5376 final i.2 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present docume

24、nt is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements

25、of that Directive, and associated EFTA regulations. The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 19 July 2016 Date of latest announcement of this EN (doa): 31 October

26、2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 April 2017 Date of withdrawal of any conflicting National Standard (dow): 30 April 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “wil

27、l“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 6 1

28、Scope The present document, together with ETSI EN 301 489-1 1, covers the assessment of Digital Enhanced Cordless Telecommunications (DECT) equipment, and associated ancillary equipment, in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emiss

29、ions from the enclosure port of the radio equipment are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment a

30、nd performance criteria for Digital Enhanced Cordless Telecommunications (DECT) equipment, and associated ancillary equipment. Definitions of types of cordless telecommunications equipment covered by the present document are given in annex B. In case of differences (for instance concerning special c

31、onditions, definitions, abbreviations) between the present document and ETSI EN 301 489-1 1, the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in ETSI EN 301 489-1 1, except f

32、or any special conditions included in the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific refe

33、rences, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the

34、 time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 489-1 (V2.1.1) (11-2016): “ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common t

35、echnical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU“. 2 Recommendation ITU-T O.153 (10-1992): “Basic parameters for the measurement of error performance at bit rat

36、es below the primary rate“. 3 ETSI EN 300 175-2 (V2.6.1) (07-2015): “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical Layer (PHL)“. 4 ETSI EN 300 175-3 (V2.6.1) (07-2015): “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 3:

37、 Medium Access Control (MAC) Layer“. 5 ETSI EN 300 176-1 (V2.2.1) (10-2015): “Digital Enhanced Cordless Telecommunications (DECT); Test specification; Part 1: Radio“. 6 CENELEC EN 55024 (2010): “Information technology equipment - Immunity characteristics - Limits and methods of measurement“. 7 ETSI

38、EN 301 406 (V2.2.0) (02-2016): “Digital Enhanced Cordless Telecommunications (DECT); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 7 8 CENELEC EN 61000-4-3 (2006), A1 (2008) and A2 (2010): “Electromagnetic

39、 compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific r

40、eferences, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The foll

41、owing referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States re

42、lating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications St

43、andards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 1 and the following apply: bea

44、rer: burst of the wanted RF signal used to establish and maintain the communications link for digital modulated and operated cordless telephone and similar radio communications equipment DECT equipment: Digital Enhanced Cordless Telecommunications (DECT) apparatus which includes one or more transcei

45、vers and/or receivers and/or parts thereof which conform to the requirements of ETSI EN 300 175-2 3 host equipment: any equipment which has a complete user functionality when not connected to the cordless telephone or similar radio communications equipment, and to which this radio equipment provides

46、 additional functionality, and to which connection is necessary for this radio equipment to offer functionality, and in which the transceiver part of the radio equipment is physically installed non-speech equipment: cordless telephone or similar communications equipment intended for the provision an

47、d reception of digital data either originating from or destined to external digital speech processing circuitry or other external equipment speech equipment: cordless telephone or similar communications equipment containing transducers such as microphones and/or loudspeakers intended for the provisi

48、on and reception of acoustic audio signals 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AC Alternative Current BER Bit Error Ratio BPF Band Pass Filter BT Bandwidth Time product BW BandWidth ETSI ETSI EN 301 489-6 V2.1.1 (2016-11) 8 CF Carrier Freque

49、ncy CFP Cordless Fixed Part CPP Cordless Portable PartCR Continuous phenomena applied to cordless telephone or communication Receive-only equipment CT Continuous phenomena applied to cordless telephone or communication Transceivers DC Direct Current DECT Digital Enhanced Cordless Telecommunications EFTA European Free Trade Association EM ElectroMagnetic EMC Electro Magnetic Compatibility ERP Ear Reference Point EUT Equipment Under Test MRP Mouth Reference PointRF Radio Frequency SPL Sound Pressure Level TR Transient phenomena applied to co