ETSI EN 301 753-2003 Fixed Radio Systems Multipoint equipment and antennas Generic harmonized standard for multipoint digital fixed radio systems and antennas covering the essentia_1.pdf

1、 ETSI EN 301 753 V1.2.1 (2003-12)Candidate Harmonized European Standard (Telecommunications series) Fixed Radio Systems;Multipoint equipment and antennas;Generic harmonized standardfor multipoint digital fixed radio systemsand antennas covering the essential requirementsunder article 3.2 of the Dire

2、ctive 1999/5/ECETSI ETSI EN 301 753 V1.2.1 (2003-12) 2 Reference REN/TM-04127 Keywords access, DRRS, DFRS, FWA, multipoint, radio, regulation, RLL, terminal ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 -

3、NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case o

4、f existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the presen

5、t document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org

6、Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of E

7、TSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 301 753 V1.2.1

8、(2003-12) 3 Contents Intellectual Property Rights4 Foreword.4 Introduction 5 1 Scope 10 2 References 14 3 Definitions, symbols and abbreviations .17 3.1 Definitions17 3.2 Symbols18 3.3 Abbreviations .18 4 Essential requirements19 4.1 General .19 4.2 Environmental specifications and tests.20 4.3 Wide

9、 radio-frequency band covering units specification and tests 20 4.3.1 Radio equipment.20 4.3.2 Antennas for FDRS.22 4.4 Specification and testing of multi-rate/multi-format equipment 23 4.5 Transmitting phenomena23 4.5.1 Frequency error/stability (radio frequency tolerance).23 4.5.2 Transmitter powe

10、r.24 4.5.3 Adjacent channel power (Spectrum mask) .25 4.5.3.1 Spectrum mask and discrete CW lines25 4.5.3.2 Remote Transmit Power Control (RTPC).28 4.5.4 Spurious emissions .29 4.5.5 Transient behaviour of the transmitter (ATPC and RFC) .29 4.5.5.1 Automatic Transmit Power Control (ATPC) 29 4.5.5.2

11、Remote Frequency Control (RFC) 30 4.6 Directional phenomena.30 4.6.1 Off-axis EIRP density (Radiation Pattern Envelope)30 4.6.2 Antenna gain.36 4.7 Receiving phenomena 41 4.7.1 Maximum usable sensitivity including duplex (BER as a function of receiver input signal level) 41 4.7.2 Co-channel interfer

12、ence sensitivity (Co-channel rejection)42 4.7.3 Adjacent channel selectivity (Adjacent channel interference sensitivity).43 4.7.4 Blocking or desensitization including duplex (CW Spurious Interference)44 4.7.5 Spurious emissions .45 4.8 Control and monitoring functions 46 4.8.1 Sharing protocols (In

13、terference avoidance requirement) 46 Annex A (normative): The EN Requirements Table (EN-RT).47 A.1 Tables of essential requirements under article 3.2 of the 1999/5/EC Directive .47 Annex B (informative): The EN title in the official languages .50 History 51 ETSI ETSI EN 301 753 V1.2.1 (2003-12) 4 In

14、tellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property R

15、ights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including

16、 IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Stand

17、ard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC 2 (as amended) laying down a procedure for th

18、e provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC 1 of the European Parliam

19、ent and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R however, legal implications on the actual declaration of conformity and equipment labelling are outside the scope of the present document. In add

20、ition, justification has been introduced in order to support clarification of issues relating to antennas and receiver parameters, commonly shared in the Fixed Service community, in their application and relationship to R FH-CDMA; FDMA, TDMA; MC-TDMA. A combination of the above may also be used. In

21、order to address different market and network requirements, with appropriate balance of cost/benefit, the ETSI standards summarized in table 2 offer a number of system types and antenna alternatives, for different network/market requirements. Under the provision of R ii) the Central Radio Station (C

22、RS) also called the radio unit which is the central base band / radio transceiver equipment. More than one CRS may be controlled by one CCS. TS: The Terminal Station (outstations with subscriber interfaces). A TS may serve more than one Terminal Equipment (TE). RS: The Repeater Station (radio repeat

23、er outstations with or without subscriber interfaces). An RS may serve one or more TS or be connected to another RS. NNI: Network Node Interface SNI: Service Node Interface (EG 202 306 38) UNI: User Network Interface (EG 202 306 38) TE: Terminal equipment ETSI ETSI EN 301 753 V1.2.1 (2003-12) 7 Figu

24、re 1 shows the most common and standardized approach for access network application; however when broadcast or private networks are concerned, different architectures are possible. For example the CS may be directly connected to the Core Network by means of a NNI interface and the switching function

25、ality may be implemented within the CS (e.g. CS is an ATM switching into an ATM network) and, for private networks, the UNI interfaces may be substituted by custom interfaces. Whenever an existing digital transmission link is available, the network implementation can be optimized by separating the C

26、CS, installed at the network node site, and the CRS. Figure 1 includes the system elements and interfaces for different types of Multipoint system (both P-MP and MP-MP). Not all system elements are necessarily deployed in any particular network. The numbers of each type of station in a real deployme

27、nt can vary considerably. Figure 1 shows only each possible type of station and each possible type of connection between stations that may occur. While in P-MP applications there are typically few CS and RS connecting large number of TS, in a typical MP-MP system, there are many RS stations and a sm

28、aller number of TS stations associated with each CS. Although a single CS is possible, as shown, a typical system will deploy several CS, each with connection to the SNI of the local switching centre or directly to the NNI of the core network(s). These interconnections may be by means of radio links

29、, optical fibre or other means. The route from the SNI to the UNI interface may be via a single radio path (typical for P-MP systems) or via one or more radio repeaters (typical for MP-MP systems). Subscriber to subscriber connections may also be provided in some networks, not routed via an external

30、 core network. The present document for multipoint systems contains only the phenomena relevant to the essential requirements according to article 3.2 of the R it provides scope for standards to be added: - under article 3.2 when new frequency bands are agreed; or - under article 3.3 should the Euro

31、pean Commission take the necessary decisions without requiring alteration of standards that are already published; it clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. ETSI ETSI EN 301 753 V1.2.1 (2003-12) 101 Scope The present docum

32、ent applies to the following FDRS types: 1) Multipoint FDRS intended for operation in frequency bands that require co-ordination; this includes both Point-to-MultiPoint and MultiPoint-to-MultiPoint FDRS; 2) Antennas for multipoint FDRS and antennas for point-to-point FDRS used at the terminal and/or

33、 repeater station of multipoint FDRS systems. These antennas may be either an integral part or may be used as a standalone part of the equipment (outdoor unit). For point-to-multipoint equipment operating in the frequency range below 1 GHz the limits of the essential phenomena off-axis EIRP density,

34、 antenna gain and cross-polar discrimination as well as their test methods may be defined by the notified body according to the R Point-to-Point Antennas; Antennas for Point to point fixed radio systems in the 1 GHz to 3 GHz band. 1 to 3 NA EN 300 636 4 V1.3.x Fixed Radio Systems; Point-to-multipoin

35、t equipment; Time Division Multiple Access (TDMA); Point-to-multipoint digital radio systems in frequency bands in the range 1 GHz to 3 GHz 1 to 3 1,75 to 4 EN 300 833 5 V1.4.x Fixed Radio Systems; Point-to-point Antennas; Antennas for point-to-point fixed radio systems operating in the frequency ba

36、nd 3 to 60 GHz 3 to 60 NA EN 301 021 6 V1.6.x Fixed Radio Systems; Point-to-multipoint equipment; Time Division Multiple Access (TDMA); Point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz 3 to 11 1,75 to 30 ETSI ETSI EN 301 753 V1.2.1 (2003-12) 11Equipment stand

37、ards ETSI Reference number Version Title Frequency range (GHz) of Fixed Service frequency bands (see note) Channel separation (MHz) EN 301 055 7 V1.4.x Fixed Radio Systems; Point-to-multipoint equipment; Direct Sequence Code Division Multiple Access (DS-CDMA); Point-to-multipoint digital radio syste

38、ms in frequency bands in the range 1 GHz to 3 GHz 1 to 3 3,5 to 14 EN 301 080 8 V1.3.x Fixed Radio Systems; Point-to-multipoint equipment; Frequency Division Multiple Access (FDMA); Point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz 3 to 11 1 to 30 EN 301 124 9

39、 V1.2.x Fixed Radio Systems; Point-to-multipoint equipment; Direct Sequence Code Division Multiple Access (DS-CDMA) point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz 3 to 11 5 to 20 EN 301 179 10 V1.2.x Fixed Radio Systems; Point-to-multipoint equipment; Frequ

40、ency Hopping Code Division Multiple Access (FH-CDMA); Point-to-multipoint Digital Radio Relay Systems (DRRS) in the bands within the range 1 GHz to 3 GHz 1 to 3 1 to 14 EN 301 213-1 11 V1.1.x Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency b

41、ands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 1: Basic parameters 24,5 to 29,5 3,5 to 112 EN 301 213-2 12 V1.3.x Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using di

42、fferent access methods; Part 2: Frequency Division Multiple Access (FDMA) methods 24,5 to 29,5 3,5 to 112 EN 301 213-3 13 V1.4.x Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access

43、methods; Part 3: Time Division Multiple Access (TDMA) methods 24,5 to 29,5 3,5 to 112 EN 301 213-4 42 V1.1.x Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 4: Dir

44、ect Sequence Code Division Multiple Access (DS-CDMA) methods 24,5 to 29,5 3,5 to 112 EN 301 213-5 43 V1.1.x Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 5: Mult

45、i-Carrier Time Division Multiple Access (MC-TDMA) methods 24,5 to 29,5 3,5 to 112 EN 301 215-1 14 V1.2.x Fixed Radio Systems; Point to Multipoint Antennas; Antennas for point-to-multipoint fixed radio systems in the 11 GHz to 60 GHz band; Part 1: General aspects 11 to 60 NA EN 301 215-2 15 V1.3.x Fi

46、xed Radio Systems; Point-to-Multipoint Antennas; Antennas for point-to-multipoint fixed radio systems in the 11 GHz to 60 GHz band; Part 2: 24 GHz to 30 GHz 24 to 30 NA ETSI ETSI EN 301 753 V1.2.1 (2003-12) 12Equipment standards ETSI Reference number Version Title Frequency range (GHz) of Fixed Serv

47、ice frequency bands (see note) Channel separation (MHz) EN 301 215-4 46 V1.1.x Fixed Radio Systems; Point to Multipoint Antennas; Antennas for multipoint fixed radio systems in the 11 GHz to 60 GHz band; Part 4: 30 GHz to 40,5 GHz 30 to 40,5 NA EN 301 253 16 V1.2.x Fixed Radio Systems; Point-to-mult

48、ipoint equipment; Frequency Hopping Code Division Multiple Access (FH-CDMA); Point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz 3 to 11 1 to 14 EN 301 373 17 V1.2.x Fixed Radio Systems; Point-to-multipoint equipment; Frequency Division Multiple Access (FDMA); P

49、oint-to-multipoint digital radio systems in frequency bands in the range 1 GHz to 3 GHz 1 to 3 0,5 to 14 EN 301 460-1 18 V1.1.x Fixed Radio Systems; Point-to-multipoint equipment; Part 1: Point-to-multipoint digital radio systems below 1 GHz - Common parameters 1 to be agreed on national basis EN 301 460-2 19 V1.1.x Fixed Radio Systems; Point-to-multipoint equipment; Part 2: Point-to-multipoint digital radio systems below 1 GHz - Additional parameters for TDMA systems 1 to be agreed on national basis EN 301 460-3 20 V1.1.x Fixe