ETSI EN 301 783-2016 Commercially available amateur radio equipment Harmonised Standard covering the essential requirements of article 3 2 of the Directive 2014 53 EU (V2 1 1)《商用业余.pdf

1、 ETSI EN 301 783 V2.1.1 (2016-01) Commercially available amateur radio equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 783 V2.1.1 (2016-01) 2 Reference REN/ERM-TG26-139 Keywords amateur, EMC,

2、mobile, radio, service ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can

3、 be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of an

4、y existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may

5、be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/Peop

6、le/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the w

7、ritten authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3G

8、PPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 783 V2.1.1 (2016-01) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Mod

9、al verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 7g33.3 Abbreviations . 7g34 General and operational requirements 7g34.1 Environmental profile . 7g34.2 EUT test

10、frequencies 7g34.3 Test power source . 8g34.3.0 General requirements 8g34.3.1 Mains voltage 8g34.3.2 Regulated lead-acid battery power sources used on vehicles 8g34.3.3 Other power sources . 8g34.4 Testing of equipment that does not have an external 50 RF connector (integral antenna equipment) . 8g3

11、4.5 Test load (artificial antenna) . 8g34.6 PEP . 8g34.7 Transmitter automatic shut-off facility . 9g34.8 Arrangement for analogue test signals at the input of the transmitter 9g34.9 Arrangement for test signals at the input of the receiver 9g34.10 Characteristics of test signals at the input of the

12、 receiver . 9g34.11 Characteristics of test signals at the input of the transmitter 9g34.11.0 General requirements 9g34.11.1 Analogue signals . 10g34.11.2 Digital signals . 10g34.12 Reference bandwidths for spurious measurements . 10g34.13 Transmit exclusion bandwidths for spurious measurements 10g3

13、4.14 Interpretation of the measurement results 11g35 Technical requirements - Transmitters . 11g35.1 Maximum power (PX) (conducted) 11g35.1.0 General requirement . 11g35.1.1 Definition 11g35.1.2 Method of measurement . 11g35.2 Unwanted emissions in the spurious domain 12g35.2.1 Definition 12g35.2.2

14、Method of measurement . 12g35.2.2.1 Method of measuring conducted spurious emissions with an artificial antenna . 12g35.2.2.2 Method of measuring the effective radiated power with an external antenna connector 12g35.2.2.3 Method of measuring the effective radiated power with an integral antenna 13g3

15、5.2.3 Limits 13g35.3 Spurious radiations . 14g35.3.1 Definition 14g35.3.2 Methods of measurement 15g35.3.2.1 Method of measuring the power level in a specified load . 15g35.3.2.2 Method of measuring the effective radiated power . 15g35.3.2.3 Method of measuring the effective radiated power . 16g35.3

16、.3 Limits 16g36 Technical requirements - Receivers . 16g36.1 Maximum usable sensitivity . 16g3ETSI ETSI EN 301 783 V2.1.1 (2016-01) 4 6.1.1 Definition 16g36.1.2 Method of measurement . 17g36.1.2.1 Amplitude modulation AM . 17g36.1.2.2 Single sideband modulation SSB 17g36.1.2.3 Frequency modulation F

17、M 17g36.1.2.4 Other types of modulation . 17g36.1.3 Limits 17g36.2 Adjacent channel selectivity . 17g36.2.1 Definition 17g36.2.2 Method of measurement . 17g36.2.2.1 Amplitude modulation AM . 17g36.2.2.2 Single sideband modulation SSB 18g36.2.2.3 Frequency modulation FM 18g36.2.2.4 Other types of mod

18、ulation . 18g36.2.3 Limits 18g36.3 Conducted RF immunity 18g36.3.1 Definition 18g36.3.2 Method of measurement . 19g36.3.2.1 Method of measurement (analogue) 19g36.3.2.2 Method of measurement (digital) 19g36.3.2.3 Unwanted signal parameters (analogue and digital) . 20g36.3.3 Limit . 20g3Annex A (norm

19、ative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 21g3History 22g3ETSI ETSI EN 301 783 V2.1.1 (2016-01) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The informat

20、ion pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETS

21、I Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the up

22、dates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared i

23、n reply to the Commissions standardisation request Commission Implementing Decision C(2015) 5376 final of 04.08.2015 to provide a means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the ma

24、rket of radio equipment. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformit

25、y with the corresponding essential requirements of that Directive and associated EFTA regulations. National transposition dates Date of adoption of this EN: 18 December 2015 Date of latest announcement of this EN (doa): 31 March 2016 Date of latest publication of new National Standard or endorsement

26、 of this EN (dop/e): 30 September 2016 Date of withdrawal of any conflicting National Standard (dow): 30 September 2017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as des

27、cribed in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 783 V2.1.1 (2016-01) 6 1 Scope The present document applies to the following radio equipme

28、nt types: Radio equipment intended to be used by radio amateurs within the meaning of article 1, definition 53, of the International Telecommunications Union (ITU) Radio Regulations 1 and which is available commercially. NOTE: This sort of equipment is traditionally supplied with an antenna connecto

29、r. The present document also specifies technical characteristics, methods of measurement and required test results. The present document contains requirements to demonstrate that “. Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum

30、 in order to avoid harmful interference“ i.5. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive i.5 may apply to equipment within the scope of the present document. 2

31、 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (includ

32、ing any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term v

33、alidity. The following referenced documents are necessary for the application of the present document. 1 ITU Radio Regulations (2012). 2 ETSI TS 103 052 (V1.1.1) (03-2011): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Radiated measurement methods and general arrangements for test

34、 sites up to 100 GHz“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced doc

35、ument (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the use

36、r with regard to a particular subject area. i.1 Recommendation ITU-R SM.329-10 (2003): “Unwanted emissions in the spurious domain“. i.2 CEPT/ERC/Recommendation 74-01 (2011): “Unwanted emissions in the spurious domain“. i.3 ETSI TR 100 028 (all parts): “Electromagnetic compatibility and Radio spectru

37、m Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. i.4 Standardisation request M/536: “Commission implementing decision of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunica

38、tions Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council“. ETSI ETSI EN 301 783 V2.1.1 (2016-01) 7 i.5 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of

39、the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Single SideBand (SSB): any emission usi

40、ng Single SideBand (SSB) suppressed carrier format 3.2 Symbols For the purposes of the present document, the following symbols apply: Bn Necessary bandwidth of an emission PX Maximum PEP 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: AM Amplitude Modul

41、ation (A3E) CBW Channel BandWidth CSP Channel SPacing DC Direct CurrentEUT Equipment Under Test FM Frequency Modulation (F3E) HF High Frequency ITU-R International Telecommunication Union, Radiocommunications sector PEP Peak Envelope Power RBW Resolution BandWidth RF Radio Frequency SINAD (Signal +

42、Noise + Distortion) / (Noise + Distortion) SSB Single SideBand (J3E) Tx Transmit UHF Ultra High Frequency VHF Very High Frequency 4 General and operational requirements 4.1 Environmental profile The environmental profile for operation of the equipment shall be declared by the supplier. The equipment

43、 shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the required operational environmental profile. 4.2 EUT test frequencies Testing shall be performed with the EUT set to frequencies as follows: single-band equipment: t

44、est at the centre of the band; double-band equipment: test at the centre of both bands; HF multi-band equipment or VHF/UHF multi-band equipment: test at the centre of the lowest, the centre of the middle, and the centre of the highest band; ETSI ETSI EN 301 783 V2.1.1 (2016-01) 8 HF/VHF, HF/UHF or H

45、F/VHF/UHF combined equipment: test at the centre of the lowest HF band, the centre of the middle HF band, the centre of the highest HF band, the centre of the lowest VHF/UHF band, the centre of the middle VHF/UHF band, and the centre of the highest VHF/UHF band. 4.3 Test power source 4.3.0 General r

46、equirements During testing the power source of the equipment shall be replaced by a test power source capable of producing the nominal supply voltage for the equipment as declared by the manufacturer. The internal impedance of the test power source shall be low enough for its effect on the test resu

47、lts to be negligible. For the purpose of tests, the voltage of the power source shall be measured at the input terminals of the equipment. For battery operated equipment the battery shall be removed and the test power source shall be applied as close to the battery terminals as practicable. During t

48、ests of DC powered equipment the power source voltages shall be maintained within a tolerance of 1 000 MHz -47 dBm (see note) NOTE: For measurement at frequencies greater than 40 GHz no test limits are specified. Where limits are stated using dBc, the reference level is PX, measured at the antenna p

49、ort according to clause 5.1. Table 8: Enclosure port limits in transmit mode Frequency range or operating mode Test Limits Remarks Mobile SSB equipment -43 dBc Below or equal to 30 MHz -(43 + 10 x log(PEP) or -50 dBc whichever is higher Above 30 MHz -(43 + 10 x log(PEP) or -70 dBc whichever is higher (see note) NOTE: For measurement at frequencies greater than 40 GHz no test limits are specified. Table 9: Enclosure port limits in transmit standby mode Frequency Range Test Limits Remarks 30 MHz to 1 000 MHz -57 dBm 1 000 MHz -47 dBm (see not