ETSI EN 301 843-2-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf

1、 ETSI EN 301 843-2 V2.1.1 (2016-03) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 2: Specific conditions for VHF radiotelephone transmitters and receivers

2、 HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 843-2 V2.1.1 (2016-03) 2 Reference REN/ERM-EMC-348 Keywords EMC, maritime, radio, regulation, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C As

3、sociation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or p

4、rint versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept

5、 on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.asp

6、x If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

7、and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All

8、 rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered

9、and owned by the GSM Association. ETSI ETSI EN 301 843-2 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Defin

10、itions 7g33.2 Symbols 7g33.3 Abbreviations . 7g34 General and operational requirements 7g34.1 Environmental profile . 7g34.2 Arrangements for test signals . 7g34.2.0 General 7g34.2.1 Arrangements for test signals at the input of the transmitter 8g34.2.2 Arrangements for test signals at the output of

11、 the transmitter 8g34.2.3 Arrangements for test signals at the input of the receiver . 8g34.2.4 Arrangements for test signals at the output of the receiver . 8g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 8g34.3 Exclusion bands 8g34.3.0 General 8g34.3.1 Exclusion b

12、ands for receivers and receiver parts of transceivers 8g34.3.2 Exclusion band for transmitters 8g34.4 Narrow band responses on receivers 8g34.5 Normal test modulation 9g35 Performance assessment . 9g35.1 General . 9g35.2 Equipment which can provide a continuous communication link 9g35.3 Equipment wh

13、ich does not provide a continuous communication link 9g35.4 Ancillary equipment . 9g35.5 Equipment classification 9g36 Performance criteria . 9g36.0 General . 9g36.1 Performance criteria A for continuous phenomena applied to transmitters and receivers 9g36.2 Performance criteria B for transient phen

14、omena applied to transmitters and receivers . 10g36.3 Performance criteria C applied to power supply failure . 10g36.4 Performance check . 10g36.4.0 General 10g36.4.1 Transmitter 10g36.4.2 Receiver 10g36.5 Performance criteria for equipment which does not provide a continuous communication link 10g3

15、6.6 Performance criteria for ancillary equipment tested on a stand-alone basis . 11g37 Applicability overview . 11g37.1 Emission . 11g37.1.1 General 11g37.1.2 Special conditions . 11g37.2 Immunity 11g37.2.1 General 11g37.2.2 Special conditions . 11g3Annex A (normative): Relationship between the pres

16、ent document and the essential requirements of Directive 2014/53/EU . 12g3ETSI ETSI EN 301 843-2 V2.1.1 (2016-03) 4 Annex B (informative): Examples of types of marine radiotelephone equipment in the scope of the present document 13g3B.0 General . 13g3B.1 Radiotelephone transmitters and receivers for

17、 the maritime mobile service operating in the VHF bands. 13g3History 14g3ETSI ETSI EN 301 843-2 V2.1.1 (2016-03) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any,

18、is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on t

19、he ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may

20、be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2

21、015) 5376 final i.7 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.2. Once the present docum

22、ent is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 of ETSI EN 301 843-1 1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding

23、 essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 21 March 2016 Date of latest announcement of t

24、his EN (doa): 30 June 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 December 2016 Date of withdrawal of any conflicting National Standard (dow): 31 December 2017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should n

25、ot“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301

26、 843-2 V2.1.1 (2016-03) 6 1 Scope The present document together with ETSI EN 301 843-1 1, covers the assessment of VHF radiotelephone transmitters and receivers for the maritime mobile service, and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications relate

27、d to the antenna port and emissions from the enclosure port of marine radiotelephone transmitters and receivers are not included in the present document. Such technical specifications are found in the related product standards for the effective use of the radio spectrum. The present document specifi

28、es the applicable test conditions, performance assessment, and performance criteria for VHF radiotelephone transmitters and receivers for the maritime mobile service, and the associated ancillary equipment. Examples of types of radiotelephone transmitters and receivers for the maritime mobile servic

29、e covered by the present document are given in annex A. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 843-1 1, the provisions of the present document take precedence. The electromagnetic environment used i

30、n the present document to develop the technical specifications encompasses the electromagnetic environment on-board ships as identified in CENELEC EN 60945 i.5. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version nu

31、mber) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at

32、http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 843-1 (V2.1.1) (03-20

33、16): “ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 1: Common technical requirements“. 2.2 Informative references References are either specific (identifi

34、ed by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clau

35、se were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Void. i.2 Directive 2014/53/EU of the Euro

36、pean Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.3 Void. ETSI ETSI EN 301 843-2 V2.1.1 (2016-03) 7 i.4 ETSI EN 302 885 (2.1.1) (03-2016): “P

37、ortable Very High Frequency (VHF) radiotelephone equipment for the maritime mobile service operating in the VHF bands with integrated handheld class D DSC; Harmonised Standard covering the essential requirements of articles 3.2 and 3.3(g) of the Directive 2014/53/EU“. i.5 CENELEC EN 60945:2002 + Cor

38、rigendum 1 (2008): “Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results“. i.6 ETSI EN 301 025 (V2.1.1) (12-2015): “VHF radiotelephone equipment for general communications and associated equipment for Class “D“ Digital

39、 Selective Calling (DSC); Harmonised Standard covering the essential requirements of articles 3.2 and 3.3(g) of the Directive 2014/53/EU“. i.7 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation a

40、nd to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in

41、 ETSI EN 301 843-1 1 apply. 3.2 Symbols For the purposes of the present document, the following symbols apply: emf electromotive force rms root mean square SINAD (Signal + Noise + Distortion)/(Noise + Distortion) 3.3 Abbreviations For the purposes of the present document, the following abbreviations

42、 apply: EMC ElectroMagnetic Compatibility EUT Equipment Under Test RF Radio Frequency 4 General and operational requirements 4.1 Environmental profile The provisions of ETSI EN 301 843-1 1, clause 4.1 shall apply with the following modifications. For emission and immunity tests the normal test modul

43、ation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5, shall apply. The test shall be carried out at a point within the specified normal operating environmental range of temperature and humidity with the equipment connected to the normal power supply voltage. 4.2 A

44、rrangements for test signals 4.2.0 General The provisions of ETSI EN 301 843-1 1, clause 4.2 shall apply. ETSI ETSI EN 301 843-2 V2.1.1 (2016-03) 8 4.2.1 Arrangements for test signals at the input of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.1 shall apply. 4.2.2 Arrangements

45、for test signals at the output of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.2 shall apply. 4.2.3 Arrangements for test signals at the input of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.3 shall apply with the following modifications. The wanted RF input si

46、gnal, coupled to the receiver, shall be modulated with normal test modulation as specified for that type of equipment (see clause 4.5). The level of the wanted signal shall be 40 dBV (emf) unless indicated otherwise. 4.2.4 Arrangements for test signals at the output of the receiver The provisions of

47、 ETSI EN 301 843-1 1, clause 4.2.4 shall apply as appropriate. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of ETSI EN 301 843-1 1, clause 4.2.5 shall apply as appropriate. 4.3 Exclusion bands 4.3.0 General The provisions of ETSI EN 301 843-1 1, claus

48、e 4.3 shall apply as appropriate. The emission measurement and immunity test exclusions are referred to as “exclusion bands“ and are defined in the clauses 4.3.1 and 4.3.2. 4.3.1 Exclusion bands for receivers and receiver parts of transceivers The exclusion band for marine radiotelephone receivers a

49、nd receivers of transceivers is the frequency range determined by the switching range, as declared by the manufacturer, extended as follows: - the lower frequency of the exclusion band is the lower frequency of the switching range, minus 5 % of the centre frequency of the switching range, or minus 10 MHz, whichever will result in the lowest frequency; - the upper frequency of the exclusion band is the upper frequency of the switching range, plus 5 % of the centre frequency of the switching range, or plus 10 MHz, whichever will