ETSI EN 301 843-2-2017 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard for electromagnetic compatibility Part 2 Specific co_1.pdf

1、 ETSI EN 301 843-2 V2.2.1 (2017-11) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard for electromagnetic compatibility; Part 2: Specific conditions for VHF radiotelephone transmitters and receivers HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301

2、 843-2 V2.2.1 (2017-11) 2 Reference REN/ERM-EMC-386 Keywords EMC, harmonised standard, maritime, radio, regulation, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucrati

3、f enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the pres

4、ent document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network dr

5、ive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in t

6、he present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as a

7、uthorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are t

8、rademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by t

9、he GSM Association. ETSI ETSI EN 301 843-2 V2.2.1 (2017-11) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2

10、Symbols 7g33.3 Abbreviations . 7g34 General and operational requirements 7g34.1 Environmental profile . 7g34.2 Arrangements for test signals . 8g34.2.0 General 8g34.2.1 Arrangements for test signals at the input of the transmitter 8g34.2.2 Arrangements for test signals at the output of the transmitt

11、er 8g34.2.3 Arrangements for test signals at the input of the receiver . 8g34.2.4 Arrangements for test signals at the output of the receiver . 8g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 8g34.3 Exclusion bands 8g34.3.0 General 8g34.3.1 Exclusion bands for recei

12、vers and receiver parts of transceivers 8g34.3.2 Exclusion band for transmitters 9g34.4 Narrow band responses on receivers 9g34.5 Normal test modulation 9g35 Performance assessment . 9g35.1 General . 9g35.2 Equipment which can provide a continuous communication link 9g35.3 Equipment which does not p

13、rovide a continuous communication link 9g35.4 Ancillary equipment . 9g35.5 Equipment classification 10g36 Performance criteria . 10g36.0 General . 10g36.1 Performance criteria A for continuous phenomena applied to transmitters and receivers 10g36.2 Performance criteria B for transient phenomena appl

14、ied to transmitters and receivers . 10g36.3 Performance criteria C applied to power supply failure . 10g36.4 Performance check . 10g36.4.0 General 10g36.4.1 Transmitter 10g36.4.2 Receiver 11g36.5 Performance criteria for equipment which does not provide a continuous communication link 11g36.6 Perfor

15、mance criteria for ancillary equipment tested on a stand-alone basis . 11g37 Applicability overview . 11g37.1 Emission . 11g37.1.1 General 11g37.1.2 Special conditions . 11g37.2 Immunity 11g37.2.1 General 11g37.2.2 Special conditions . 12g3ETSI ETSI EN 301 843-2 V2.2.1 (2017-11) 4 Annex A (informati

16、ve): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 13g3Annex B (informative): Examples of types of marine radiotelephone equipment in the scope of the present document 15g3B.1 Radiotelephone transmitters and receivers for the maritime mobile servi

17、ce operating in the VHF bands. 15g3Annex C (informative): Bibliography . 16g3Annex D (informative): Change history . 17g3History 18g3ETSI ETSI EN 301 843-2 V2.2.1 (2017-11) 5 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been

18、declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, w

19、hich is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced

20、 in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except

21、for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

22、Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.7 to provide one voluntary means of

23、conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.2. Once the present document is cited in the Official Journal of the European U

24、nion under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. T

25、he present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 17 October 2017 Date of latest announcement of this EN (doa): 31 January 2018 Date of latest publication of new National St

26、andard or endorsement of this EN (dop/e): 31 July 2018 Date of withdrawal of any conflicting National Standard (dow): 31 July 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpr

27、eted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 843-2 V2.2.1 (2017-11) 6 1 Scope The present document together with ETSI EN 301

28、 843-1 1, covers the assessment of VHF radiotelephone transmitters and receivers for the maritime mobile service, and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of marine radiotelep

29、hone transmitters and receivers are not included in the present document. Such technical specifications are found in the related product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment, and performance crite

30、ria for VHF radiotelephone transmitters and receivers for the maritime mobile service, and the associated ancillary equipment. Examples of types of radiotelephone transmitters and receivers for the maritime mobile service covered by the present document are given in annex A. In case of differences (

31、for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 843-1 1, the provisions of the present document take precedence. The electromagnetic environment used in the present document to develop the technical specifications encompasses the e

32、lectromagnetic environment on-board ships as identified in IEC EN 60945 i.5. NOTE: The relationship between the present document and essential requirements of article 3.1b of Directive 2014/53/EU i.2 is given in annex A. 2 References 2.1 Normative references References are specific, identified by da

33、te of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at

34、the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 843-1 (V2.2.1) (11-2017): “ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmon

35、ised Standard for electromagnetic compatibility; Part 1: Common technical requirements“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For

36、 non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary f

37、or the application of the present document but they assist the user with regard to a particular subject area. i.1 Void. ETSI ETSI EN 301 843-2 V2.2.1 (2017-11) 7 i.2 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member Sta

38、tes relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.3 Void. i.4 ETSI EN 302 885: “Portable Very High Frequency (VHF) radiotelephone equipment for the maritime mobile service operating in the VHF bands with integrated handheld class H DSC; Harmon

39、ised Standard covering the essential requirements of articles 3.2 and 3.3(g) of Directive 2014/53/EU“. i.5 IEC EN 60945 (2002) + Corrigendum 1 (2008): “Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results“. i.6 ETSI EN

40、 301 025: “VHF radiotelephone equipment for general communications and associated equipment for Class “D“ Digital Selective Calling (DSC); Harmonised Standard covering the essential requirements of articles 3.2 and 3.3(g) of the Directive 2014/53/EU“. i.7 Commission Implementing Decision C(2015) 537

41、6 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbo

42、ls and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 843-1 1 apply. 3.2 Symbols For the purposes of the present document, the following symbols apply: emf electromotive force rms root mean square SINAD (Signal + Noise + Distort

43、ion) / (Noise + Distortion) 3.3 Abbreviations For the purposes of the present document, the abbreviations given in ETSI EN 301 843-1 1 and the following apply: EMC ElectroMagnetic Compatibility EUT Equipment Under Test RF Radio Frequency 4 General and operational requirements 4.1 Environmental profi

44、le The provisions of ETSI EN 301 843-1 1, clause 4.1 shall apply with the following modifications. For emission and immunity tests the normal test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5, shall apply. The test shall be carried out at a point with

45、in the specified normal operating environmental range of temperature and humidity with the equipment connected to the normal power supply voltage. ETSI ETSI EN 301 843-2 V2.2.1 (2017-11) 8 4.2 Arrangements for test signals 4.2.0 General The provisions of ETSI EN 301 843-1 1, clause 4.2 shall apply.

46、4.2.1 Arrangements for test signals at the input of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.1 shall apply. 4.2.2 Arrangements for test signals at the output of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.2 shall apply. 4.2.3 Arrangements for test signa

47、ls at the input of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.3 shall apply with the following modifications. The wanted RF input signal, coupled to the receiver, shall be modulated with normal test modulation as specified for that type of equipment (see clause 4.5). The level of

48、 the wanted signal shall be 40 dBV (emf) unless indicated otherwise. 4.2.4 Arrangements for test signals at the output of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.4 shall apply as appropriate. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The pr

49、ovisions of ETSI EN 301 843-1 1, clause 4.2.5 shall apply as appropriate. 4.3 Exclusion bands 4.3.0 General The provisions of ETSI EN 301 843-1 1, clause 4.3 shall apply as appropriate. The emission measurement and immunity test exclusions are referred to as “exclusion bands“ and are defined in the clauses 4.3.1 and 4.3.2. 4.3.1 Exclusion bands for receivers and receiver parts of transceivers The exclusion band for marine radiotelephone receivers and receivers of transceivers is the frequency range determined by the switchin