ETSI EN 301 908-2-2017 IMT cellular networks Harmonised Standard covering the essential requirements of article 3 2 of Directive 2014 53 EU Part 2 CDMA Direct Spread (UTRA FDD) Use.pdf

1、 ETSI EN 301 908-2 V11.1.2 (2017-08) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE) HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)2 Reference REN/M

2、SG-TFES-11-02-RED-C1 Keywords 3G, 3GPP, cellular, digital, IMT, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistr

3、e la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present documen

4、t shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within

5、ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present

6、document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized b

7、y written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks o

8、f ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Asso

9、ciation. ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)3 Contents Intellectual Property Rights 7g3Foreword . 7g3Modal verbs terminology 7g3Introduction 8g31 Scope 9g32 References 10g32.1 Normative references . 10g32.2 Informative references 10g33 Definitions, symbols and abbreviations . 11g33.1 Definition

10、s 11g33.2 Symbols 12g33.3 Abbreviations . 13g34 Technical requirements specifications . 14g34.1 Environmental profile . 14g34.2 Conformance requirements 14g34.2.0 General 14g34.2.1 Introduction. 14g34.2.2 Transmitter maximum output power. 15g34.2.2.1 Transmitter maximum output power . 15g34.2.2.1.1

11、Definition. 15g34.2.2.1.2 Limits 15g34.2.2.1.3 Conformance . 16g34.2.2.2 Transmitter maximum output power for DC-HSUPA 16g34.2.2.2.1 Definition for DC-HSUPA 16g34.2.2.2.2 Limits for DC-HSUPA 16g34.2.2.2.3 Conformance . 16g34.2.2.3 Transmitter maximum output power for UL OLTD . 16g34.2.2.3.1 Definiti

12、on for UL OLTD . 16g34.2.2.3.2 Limits for UL OLTD . 16g34.2.2.3.3 Conformance . 17g34.2.3 Transmitter spectrum emission mask 17g34.2.3.1 Transmitter spectrum emission mask 17g34.2.3.1.1 Definition. 17g34.2.3.1.2 Limits 17g34.2.3.1.3 Conformance . 18g34.2.3.2 Transmitter spectrum emission mask for DC

13、-HSUPA . 18g34.2.3.2.1 Definition for DC-HSUPA 18g34.2.3.2.2 Limits for DC-HSUPA 18g34.2.3.2.3 Conformance . 18g34.2.3.3 Transmitter spectrum emission mask for UL OLTD 19g34.2.3.3.1 Definition for UL OLTD . 19g34.2.3.3.2 Limits for UL OLTD . 19g34.2.3.3.3 Conformance . 19g34.2.3.4 Transmitter spectr

14、um emission mask for UL CLTD Activation state 1 19g34.2.3.4.1 Definition for UL CLTD Activation state 1 19g34.2.3.4.2 Limits for UL CLTD Activation state 1 19g34.2.3.4.3 Conformance . 20g34.2.4 Transmitter spurious emissions . 20g34.2.4.1 Transmitter spurious emissions . 20g34.2.4.1.1 Definition. 20

15、g34.2.4.1.2 Limits 20g34.2.4.1.3 Conformance . 22g34.2.4.2 Transmitter spurious emissions for DC-HSUPA 22g34.2.4.2.1 Definition for DC-HSUPA 22g3ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)4 4.2.4.2.2 Limits for DC-HSUPA 22g34.2.4.2.3 Conformance . 24g34.2.5 Transmitter minimum output power . 25g34.2.5.

16、1 Transmitter minimum output power 25g34.2.5.1.1 Definition. 25g34.2.5.1.2 Limits 25g34.2.5.1.3 Conformance . 25g34.2.5.2 Transmitter minimum output power for DC-HSUPA . 25g34.2.5.2.1 Definition for DC-HSUPA 25g34.2.5.2.2 Limits for DC-HSUPA 25g34.2.5.2.3 Conformance . 25g34.2.5.3 Transmitter minimu

17、m output power for UL CLTD Activation state 1 . 25g34.2.5.3.1 Definition for UL CLTD Activation state 1 25g34.2.5.3.2 Limits for UL CLTD Activation state 1 25g34.2.5.3.3 Conformance . 25g34.2.6 Receiver Adjacent Channel Selectivity (ACS) . 26g34.2.6.1 Definition 26g34.2.6.2 Limits 26g34.2.6.3 Confor

18、mance . 26g34.2.7 Receiver blocking characteristics . 26g34.2.7.1 Definition 26g34.2.7.2 Limits 26g34.2.7.3 Conformance . 28g34.2.8 Receiver spurious response . 28g34.2.8.1 Definition 28g34.2.8.2 Limits 28g34.2.8.3 Conformance . 29g34.2.9 Receiver intermodulation characteristics 29g34.2.9.1 Definiti

19、on 29g34.2.9.2 Limits 29g34.2.9.3 Conformance . 30g34.2.10 Receiver spurious emissions . 30g34.2.10.1 Definition 30g34.2.10.2 Limits 30g34.2.10.3 Conformance . 31g34.2.11 Out-of-synchronization handling of output power 31g34.2.11.1 Definition 31g34.2.11.2 Limits 31g34.2.11.3 Conformance . 33g34.2.12

20、 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 33g34.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) 33g34.2.12.1.1 Definition. 33g34.2.12.1.2 Limits 33g34.2.12.1.3 Conformance . 33g34.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA 33g34.2.12.2.1 Definition for D

21、C-HSUPA 33g34.2.12.2.2 Limits for DC-HSUPA 33g34.2.12.2.3 Conformance . 34g34.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 34g34.2.12.3.1 Definition for UL OLTD . 34g34.2.12.3.2 Limits for UL OLTD . 34g34.2.12.3.3 Conformance . 34g34.2.12.4 Adjacent channel leakage power ratio for UL CL

22、TD Activation state 1 34g34.2.12.4.1 Definition for UL CLTD Activation state 1 34g34.2.12.4.2 Limits for UL CLTD Activation state 1 34g34.2.12.4.3 Conformance . 35g34.2.13 Receiver Reference Sensitivity level 35g34.2.13.0 General 35g34.2.13.1 Definition 35g34.2.13.2 Limits 35g34.2.13.3 Conformance .

23、 35g3ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)5 5 Testing for compliance with technical requirements 35g35.1 Environmental conditions for testing . 35g35.2 Interpretation of the measurement results 36g35.3 Essential radio test suites 37g35.3.0 General 37g35.3.1 Transmitter maximum output power. 37g35

24、.3.1.1 Method of test . 37g35.3.1.1.1 UTRA 37g35.3.1.1.1A DC-HSUPA . 38g35.3.1.1.1B UL OLTD 38g35.3.1.2 Test requirements 39g35.3.2 Transmitter spectrum emission mask 39g35.3.2.1 Method of test . 39g35.3.2.1.1 UEs not supporting HSDPA and/or E-DCH 39g35.3.2.1.1A UEs supporting HSDPA and/or E-DCH 40g

25、35.3.2.1.1B DC-HSUPA . 40g35.3.2.1.1C UL OLTD 41g35.3.2.1.1D UL CLTD Activation state 1 . 42g35.3.2.2 Test requirements 42g35.3.3 Transmitter spurious emissions . 42g35.3.3.1 Method of test . 42g35.3.3.1.1 UTRA 42g35.3.3.1.1A DC-HSUPA . 43g35.3.3.2 Test requirements 43g35.3.4 Transmitter minimum out

26、put power . 44g35.3.4.1 Method of test . 44g35.3.4.1.1 UTRA 44g35.3.4.1.1A DC-HSUPA . 44g35.3.4.1.1B UL CLTD Activation state 1 . 45g35.3.4.2 Test requirements 45g35.3.5 Receiver Adjacent Channel Selectivity (ACS) . 45g35.3.5.1 Method of test . 45g35.3.5.1.1 Initial conditions 45g35.3.5.1.2 Procedur

27、e . 46g35.3.5.2 Test requirements 46g35.3.6 Receiver blocking characteristics . 46g35.3.6.1 Method of test . 46g35.3.6.1.1 Initial requirements 46g35.3.6.1.2 Procedure . 46g35.3.6.2 Test requirements 46g35.3.7 Receiver spurious response . 47g35.3.7.1 Method of test . 47g35.3.7.1.1 Initial conditions

28、 47g35.3.7.1.2 Procedure . 47g35.3.7.2 Test requirements 47g35.3.8 Receiver Intermodulation characteristics 47g35.3.8.1 Method of test . 47g35.3.8.1.1 Initial conditions 47g35.3.8.1.2 Procedure . 48g35.3.8.2 Test requirements 48g35.3.9 Receiver spurious emissions . 48g35.3.9.1 Method of test . 48g35

29、.3.9.1.1 Initial conditions 48g35.3.9.1.2 Procedure . 48g35.3.9.2 Test requirements 48g35.3.10 Out-of-synchronization handling of output power 48g35.3.10.1 Method of test . 48g35.3.10.1.1 Initial conditions 48g35.3.10.1.2 Procedure . 49g35.3.10.2 Test requirements 49g35.3.11 Transmitter adjacent cha

30、nnel leakage power ratio 49g35.3.11.1 Method of test . 49g3ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)6 5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH 49g35.3.11.1.1A UEs supporting HSDPA and/or E-DCH 50g35.3.11.1.1B DC-HSUPA . 50g35.3.11.1.1C UL OLTD 51g35.3.11.1.1D UL CLTD Activation state 1 . 51g3

31、5.3.11.2 Test requirements 52g35.3.12 Receiver Reference Sensitivity level 52g35.3.12.1 Method of test . 52g35.3.12.1.1 Initial conditions 52g35.3.12.1.2 Procedure . 52g35.3.12.2 Test requirements 52g3Annex A (informative): Relationship between the present document and the essential requirements of

32、Directive 2014/53/EU . 53g3Annex B (normative): Environmental profile . 54g3B.1 General . 54g3B.1.1 Introduction 54g3B.1.2 Temperature . 54g3B.1.3 Voltage . 54g3B.1.4 Test environment 54g3Annex C (informative): Bibliography . 55g3Annex D (informative): Change history . 56g3History 57g3ETSI ETSI EN 3

33、01 908-2 V11.1.2 (2017-08)7 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be fo

34、und in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR P

35、olicy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The

36、present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of thos

37、e trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document ha

38、s been prepared under the Commissions standardisation request C(2015) 5376 final i.9 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipm

39、ent and repealing Directive 1999/5/EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presum

40、ption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.10. National transposition dates Date of latest announcement of

41、 this EN (doa): 30 November 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 May 2018 Date of withdrawal of any conflicting National Standard (dow): 31 May 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“,

42、 “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 908

43、-2 V11.1.2 (2017-08)8 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the Radio Equipment Directive i.2. The present document is produced f

44、ollowing the guidance in ETSI EG 203 336 i.3 as applicable. ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)9 1 Scope The present document applies to the following radio equipment type: User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD). These radio equipment types are capable of operating in all or

45、any part of the frequency bands given in table 1-1. Table 1-1: UTRA FDD operating bands UTRA FDD Band Direction of transmission UTRA FDD operating bands I Transmit 1 920 MHz to 1 980 MHz Receive 2 110 MHz to 2 170 MHz III Transmit 1 710 MHz to 1 785 MHz Receive 1 805 MHz to 1 880 MHz VII Transmit 2

46、500 MHz to 2 570 MHz Receive 2 620 MHz to 2 690 MHz VIII Transmit 880 MHz to 915 MHz Receive 925 MHz to 960 MHz XV Transmit 1 900 MHz to 1 920 MHz Receive 2 600 MHz to 2 620 MHz XVI Transmit 2 010 MHz to 2 025 MHz Receive 2 585 MHz to 2 600 MHz XX Transmit 832 MHz to 862 MHz Receive 791 MHz to 821 M

47、Hz XXII Transmit 3 410 MHz to 3 490 MHz Receive 3 510 MHz to 3 590 MHz The present document covers requirements for UTRA FDD User Equipment from 3GPP Releases 99, 4, 5, 6, 7, 8, 9, 10 and 11 defined in ETSI TS 125 101 4. This include the requirements for UE operating bands from 3GPP Release 12 defin

48、ed in ETSI TS 125 101 4. In addition, the present document covers requirements for UTRA FDD User Equipment in the operating bands specified in ETSI TS 102 735 i.4. NOTE: For Band XX: - for user equipment designed to be mobile or nomadic, the requirements in the present document measured at the anten

49、na port also show conformity to the corresponding requirement defined as TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU i.6, ECC Decision (09)03 i.7 and CEPT Report 30 i.8; - for user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU i.6, ECC Decision (09)03 i.7 and CEPT Report 30 i.8. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radi