ETSI EN 302 039-2-2002 Intelligent Network (IN) Intelligent Network Capability Set 4 (CS4) Intelligent Network Application Protocol (INAP) Protocol Specification Part 2 Service Swi_1.pdf

1、ETSI EN 302 039-2 1.1.2 (2002-11) European Sfandard (Telecornrnunicafions series) Intelligent Network (IN); Intelligent Network Capability Set 4 (CS4); Intelligent Network Application Protocol (INAP); Protocol specification; Part 2: Service Switching Function - Switching Control Function (SSF-SCF) I

2、nterface 2 ETSI EN 302 039-2 VI .I .2 (2002-1 1) Reference DENISPAN-I 20065-2 Keywords CS4, IN, INAP, protocol ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregi

3、stre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:lwmv.etsi .arq The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in conte

4、nts between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the documen

5、t may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors in the present document, send your comment to: Cori vriaht Notifica tion No part may be reproduc

6、ed except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2002. All rights reserved. DECTTM, PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members.

7、 TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 ETSI EN 302 039-2 VI .I .2 (2002-1 1) Contents Intellectual Proper

8、ty Rights . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Foreword 1 Scope . 2 References .

9、 . . .5 3 Abbreviations . . .6 4 Operation procedures . . . . .6 4.1 6 4.1.1 6 6 4.1.2 4.1.3 6 4.1.4 6 4.1.5 7 4.1.6 7 4.1.7 7 7 4.1.8 7 4.2 7 4.2.1 . 7 4.2.1.1 General description . 7 4.2.1.2 Argument Paramete . 8 4.2.1.3 . 8 4.2.1.3.1 . 8 4.2.1.3.2 . 8 8 4.2.1.4.1 . 8 4.2.1.4.2 . Modified operatio

10、ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect. . . ContinueWithArgument . . . . . . . . . . . . . . . . . . . . . . ImtialDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . InitiateCallAttempt . . . . . . . . . . . . . . . .

11、. . . . . . . . . . . . . MergeCallSegments . . . . . . . . . . . . . . . . . . . . . . . . . . . . MoveLeg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SelectFacility . . . . . . . . . . . . SplitLeg . . . . . . . . . . . . . . . . . . . . New operations

12、 . . . 4.2.1.4 Responding entity . 5 5.1 5.2 5.3 5.4 5.5 5.6 6 6.1 6.2 6.3 6.4 6.5 6.5.1 6.5.2 6.5.3 Parameter descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13、. . . . . . . . . . . . .9 Detachsignallingpath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DestinationIndex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Export Signallingpath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Incoming

14、SignallingBufferCopy . . . . . . . . . . . . . . . 9 IPRelatedInformation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Merge Signalling Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ASN. 1 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 O Data Types . 10 Classes . 35 Operations and Arguments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16、 . . . . . . . 39 Operation timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Packages, contracts, applicatio

17、n contexts and abstract syntaxes .63 ASN.l modules . . . .63 Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Abstract Syntaxes . . 73 Annex A (informative): Bibliography . 79 History . . . .80

18、 ETSI 4 ETSI EN 302 039-2 VI .I .2 (2002-1 1) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be fo

19、und in ETSI SR O00 3 14: “Intellectual Property Rights (7PRs); Essential, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (5). Pursuant to the ETSI IPR Policy, no investigat

20、ion, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (T

21、elecommunications series) has been produced by ETSI Technical Committee Services and Protocols for Advanced Networks (SPAN). The present document is part 2 of a multi-part deliverable covering Intelligent Network (IN); Intelligence Network Capability Set 4 (CS4); Intelligent Network Application Prot

22、ocol (INAP); Protocol specification, as identified below: Part 1 : “Common aspects“; Part 2: “Service Switching Function - Switching Control Function (SSF-SCF) Interface“. The present document describes the enhancement for SSF-SCF interface. The present document and EN 302 039-1 i define the Intelli

23、gent Network (IN) Application Protocol (INAP) for IN Capability Set-4 based and written as delta documents upon ETSI Core INAP CS-3 (EN 301 931-1 2 and EN 301 931-2 3). This set of documents define enhancements made on the SSF to SCF interface (the present document) as a subset of the ITU-T IN CS4 R

24、ecommendations Q.1248.1 lo, Q.1248.2 li. For the other interfaces, the ETSI Core INAP CS3 series of EN 301 93 1 2 and 3 apply. National transposition dates Date of adoption of this EN: Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of

25、 this EN (dop/e): Date of withdrawal of any conflicting National Standard (dow): 15 November 2002 28 February 2003 3 1 August 2003 3 1 August 2003 ETSI 5 ETSI EN 302 039-2 VI .I .2 (2002-1 1) 1 Scope The present document specifies the protocol enhancements on the SSF-SCF interface for IN CS4. 2 Re f

26、e re nces The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication andor edition number or version number) or non-specific. For a specific reference, subsequent r

27、evisions do not apply. For a non-specific reference, the latest version applies. il ETSI EN 302 039-1 : “Intelligent Network (IN); Intelligent Network Capability Set 4 (CS4); Intelligent Network Application Protocol (INAP); Protocol specification; Part 1 : Common aspects“. ETSI EN 301 93 1-1: “Intel

28、ligent Network (IN); Intelligent Network Capability Set 3 (CS3); Intelligent Network Application Protocol (INAP); Protocol specification; Part 1 : Common aspects“. ETSI EN 301 93 1-2: “Intelligent Network (IN); Intelligent Network Capability Set 3 (CS3); Intelligent Network Application Protocol (INA

29、P); Protocol specification; Part 2: SCF-SSF interface“. 21 31 41 ETSI EN 301 93 1-3: “Intelligent Network (IN); Intelligent Network Capability Set 3 (CS3); Intelligent Network Application Protocol (INAP); Protocol specification; Part 3 : SCF-SRF interface I. 51 ETSI TS 122 024:“Digital cellular tele

30、communications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Description of Charge Advice Information (CAI) (3GPP TS 22.024)“. ETSI EN 301 070-1 : “Integrated Services Digital Network (ISDN); Signalling System N0.7; ISDN User Part (ISUP) version 3 interactions with the Intell

31、igent Network Application Part (INAP); Part 1 : Protocol specification ITU-T Recommendation Q. 1600 (1 997), modified“. 61 71 EST1 TS 123 040: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Technical realization of the Short Message Service

32、 (SMS) (3GPP TS 23.040)“. ITU-T Recommendation E.4 1 O: “International network management - General information“. ITU-T Recommendation Q. 1236: “Intelligent Network Capability Set 3 - Management Information Model Requirements and Methodology“. ITU-T Recommendation Q. 1248.1 : “Interface recommendati

33、on for Intelligent Network Capability Set 4: Interface Recommendation for Intelligent Network Capability Set 4 - Common aspects“. ITU-T Recommendation Q. 1248.2: Interface recommendation for Intelligent Network Capability Set 4: SCF-SSF Interface“. ITU-T Recommendation H.323 : “Packet-based multimed

34、ia communications systems“ ITU-T Recommendation H.450.3: “Call diversion supplementary service for H.323“. ITU-T Recommendation Q.763: “Signalling System No. 7 - ISDN User Part formats and codes“ ETSI 6 ETSI EN 302 039-2 VI .I .2 (2002-1 1) i51 ITU-T Recommendation Q. 850: “Usage of cause and locati

35、on in the Digital Subscriber Signalling System No. 1 and the Signalling System No. 7 ISDN User Part“. ITU-T Recommendation Q.735.1: “Stage 3 description for community of interest supplementary services using Signalling System No. 7: Closed user group (CUG)“. ITU-T Recommendation Q.93 1 : “ISDN user-

36、network interface layer 3 specification for basic call control“. 161 i71 I81 i91 ITU-T Recommendation Q.7 13 : “Signalling connection control part formats and codes“. ITU-T Recommendation Q. 1601: “Signalling system No. 7 - Interaction between N-ISDN and INAP CS2“. 201 ITU-T Recommendation Q. 123 8:

37、 “Interface Recommendation for intelligent network capability set 3“. 3 Abbreviations For the purposes of the present document, the abbreviations given in EN 30 1 93 1 - 1 2 apply. 4 Opera ti on proced u res EN 301 93 1-2 3, clause 11 is applicable with the enhancements specified in the present docu

38、ment. 4.1 Modified operations The following operations defined in EN 301 93 1-2 3 are modified by the present document. 4.1.1 Connect The following parameter defined in clause 5 is added to the operation argument: - IpRelatedInformation. Existing cug-Interlock and cug-OutgoingAcces parameters are no

39、 longer restricted for the support of CAMEL. 4.1.2 ContinueWithArgument The following parameter defined in clause 5 is added to the operation argument: - ipRelatedInformation. 4.1.3 InitialDP The following parameter defined in clause 5 is added to the operation argument: - ipRelatedInformation. 4.1.

40、4 InitiateCallAttempt The following parameters defined in clause 5 are added to the operation argument: - incomingSignallingBufferCopy. - ipRelatedInformation. ETSI 7 ETSI EN 302 039-2 VI .I .2 (2002-1 1) 4.1.5 MergeCallSegments The following parameter defined in clause 5 is added to the operation a

41、rgument: - mergeSignallingPaths. 4.1.6 MoveLeg The following parameters defined in clause 5 are added to the operation argument: - detachsignallingpath. - exportSignallingPath. 4.1.7 SelectFacility The following parameter defined in clause 5 is added to the operation argument: - ipRelatedInformation

42、. 4.1.8 SplitLeg The following parameter defined in clause 5 is added to the operation argument: - detachsignallingpath. 4.2 New operations The following new operation is defined by the present document. 4.2.1 CallFiltering procedure 4.2.1 .I General description The CallFiltering operation is used t

43、o allow the SCF to influence basic call gapping procedures based in the CCF by sending information from the SCF to the SSF. The SSF relays the received information transparently to the CCF. This way, the SCF can influence the rate at which call attempts are allowed through. The operation thus influe

44、nces the filtering of calls, as opposed to service requests as is done by the Callgap operation. 4.2.1.2 Arg u ment Param eters The operation argument consists of the following parameters. These parameters are defined in clause 13. - destination Index This index is a pointer to the Destination (see

45、ITU-T Recommendation E.410 SI) to which calls are filtered. - gapIndicators The parameter contains the gapDuration and the gapInterval. - registratorIdentifier This parameter identifies the SCF and is to be used by the SSF to veriSl that the SCF is allowed to influence CCF-based call gapping procedu

46、res. - extensions ETSI 8 ETSI EN 302 039-2 VI .I .2 (2002-1 1) 4.2.1.3 Invoking entity (SCF) 4.2.1.3.1 Normal procedure SCF precondition: 1) The SCF receives an indication from the SMF an overload condition persists and callfiltering has to be initiated at the SSF. SCF postcondition: 1) The SCME is

47、in the state “idle“. If the congestion level changes new “CallFIltering“ operations may be sent for active filter criteria but with a new filter interval. If the congestion situation has ended, the filtering criteria may be removed. 4.2.1.3.2 Error handling Generic error handling for the operation r

48、elated error are described in clause 13 of EN 301 93 1-2 3 and the TCAP services which are used for reporting operation errors as described in clause 10 of EN 301 93 1-1 2. 4.2.1.4 Responding entity (SSF) 4.2.1.4.1 Normal procedure SSF precondition: 1) None. SSF postcondition: 1) SSME-FSM is in the

49、state “Idle“. The SSF relays the received information transparently to the CCF-based call filtering process. In case callfiltering to the specific destinations is already active at the CCF, than the new gapIndicator parameter overwrites the existing parameter values. A manual initiated call filter will prevail over an automatic initiated call filt