ETSI EN 302 213-2004 Services and Protocols for Advanced Networks (SPAN) Bearer Independant Call Control (BICC) Capability Set 2 (CS2) Protocol specification (V1 1 2 ITU-T Recommen.pdf

1、 ETSI EN 302 213 V1.1.2 (2004-01)European Standard (Telecommunications series) Services and Protocols for Advanced Networks (SPAN);Bearer Independent Call Control (BICC) Capability Set 2 (CS2);Protocol specificationITU-T Recommendations Q.1902.1, Q.1902.2, Q.1902.3, Q.1902.4, Q.1902.5, Q.1902.6,Q.76

2、5.5 Amendment 1, Q.1912.1, Q.1912.2, Q.1912.3, Q.1912.4, Q.1922.2, Q.1950, Q.1970,Q.1990, Q.2150.0, Q.2150.1, Q.2150.2, Q.2150.3, modifiedETSI ETSI EN 302 213 V1.1.2 (2004-01) 2 Reference DEN/SPAN-130261 Keywords APM, ATM, BICC, CS2, endorsement, interworking, IP, ISDN, SS7 ETSI 650 Route des Luciol

3、es F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/

4、www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the prin

5、ting on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/

6、portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European

7、 Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark o

8、f ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 302 213 V1.1.2 (2004-01) 3 Contents Intellectual Property Rights4 Foreword.4 1 Scope 5 2 References 5 3 Definitions and abbreviations.8 4 Endorsement notice9 4.1 Q.1902.1.9 4.2 Q.1902.2.12 4.3 Q.19

9、02.3.12 4.4 Q.1902.4.15 4.5 Q.1902.5.16 4.6 Q.1902.6.16 4.7 Q.765.5.16 4.8 Q.765.5 Amendment 1 .17 4.9 Q.1912.1.17 4.10 Q.1912.2.18 4.11 Q.1912.3.19 4.12 Q.1912.4.20 4.13 Q.1922.2.20 4.14 Q.195021 4.15 Q.197021 4.16 Q.199022 4.17 Q.2150.0.22 4.18 Q.2150.1.22 4.19 Q.2150.2.22 4.20 Q.2150.3.23 Annex Z

10、A (informative): Coding of the compatibility information for basic call procedures.24 Annex ZB (informative): Bibliography.25 History 26 ETSI ETSI EN 302 213 V1.1.2 (2004-01) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI

11、. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is availabl

12、e from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced i

13、n ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Services and Protocols for Advanced Networks (SPAN). National tr

14、ansposition dates Date of adoption of this EN: 19 December 2003 Date of latest announcement of this EN (doa): 31 March 2004 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 September 2004 Date of withdrawal of any conflicting National Standard (dow): 30 Septe

15、mber 2004 ETSI ETSI EN 302 213 V1.1.2 (2004-01) 5 1 Scope The present document provides the ETSI endorsement of the ITU-T Bearer Independent Call Control (BICC) Capability Set 2 protocol Recommendations Q.1902.1 1, Q.1902.2 2, Q.1902.3 3, Q.1902.4 4, Q.1902.5 5, Q.1902.6 6, Q.765.5 7 Amendment 1 8,Q

16、.1912.1 9, Q.1912.2 10, Q.1912.3 11, Q.1912.4 12, Q.1922.2 13, Q.1950 14, Q.1970 15, Q.1990 16, Q.2150.0 17, Q.2150.1 18, Q.2150.2 19, Q.2150.3 20. Formats, codes and procedures marked for national use or as network option are included for informative purposes for the international interface specifi

17、cation. If these items so marked are supported within a national network and operators network, then it is proposed that they shall be supported in this manner. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present documen

18、t. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicl

19、y available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ITU-T Recommendation Q.1902.1: “Bearer Independent Call Control protocol (Capability Set 2): Functional description“. 2 ITU-T Recommendation Q.1902.2: “Bearer Independent Call Control protocol (Capability Set 2

20、) and Signalling System No. 7 ISDN user part: General functions of messages and parameters“. 3 ITU-T Recommendation Q.1902.3: “Bearer Independent Call Control protocol (Capability Set 2) and Signalling System No. 7 ISDN user part: Formats and codes“. 4 ITU-T Recommendation Q.1902.4: “Bearer Independ

21、ent Call Control protocol (Capability Set 2): Basic call procedures“. 5 ITU-T Recommendation Q.1902.5: “Bearer Independent Call Control protocol (Capability Set 2): Exceptions to the application transport mechanism in the context of BICC“. 6 ITU-T Recommendation Q.1902.6: “Bearer Independent Call Co

22、ntrol protocol (Capability Set 2): Generic signalling procedures for the support of the ISDN user part supplementary services and for bearer redirection“. 7 ITU-T Recommendation Q.765.5: “Signalling system No. 7 - Application transport mechanism: Bearer Independent Call Control (BICC)“. 8 ITU-T Reco

23、mmendation Q.765.5 Amendment 1: “Bearer Independent Call Control Capability Set 2“. 9 ITU-T Recommendation Q.1912.1: “Interworking between Signalling System No. 7 ISDN user part and the Bearer Independent Call Control protocol“. 10 ITU-T Recommendation Q.1912.2: “Interworking between selected signal

24、ling systems (PSTN access, DSS1, C5, R1, R2, TUP) and the Bearer Independent Call Control protocol“. 11 ITU-T Recommendation Q.1912.3: “Interworking between H.323 and the Bearer Independent Call Control protocol“. ETSI ETSI EN 302 213 V1.1.2 (2004-01) 6 12 ITU-T Recommendation Q.1912.4: “Interworkin

25、g between Digital Subscriber Signalling System No. 2 and the Bearer Independent Call Control protocol“. 13 ITU-T Recommendation Q.1922.2: “Interaction between the Intelligent Network application protocol Capability set 2 and the Bearer independent call control protocol“. 14 ITU-T Recommendation Q.19

26、50: “Bearer independent call bearer control protocol“. 15 ITU-T Recommendation Q.1970: “BICC IP Bearer control protocol“. 16 ITU-T Recommendation Q.1990: “BICC Bearer Control Tunnelling Protocol“. 17 ITU-T Recommendation Q.2150.0: “Generic signalling transport service“. 18 ITU-T Recommendation Q.215

27、0.1: “Signalling Transport Converter on MTP3 and MTP3b“. 19 ITU-T Recommendation Q.2150.2: “Signalling transport converter on SSCOP and SSCOPMCE“. 20 ITU-T Recommendation Q.2150.3: “Signalling transport converter on SCTP“. 21 ETSI EN 301 069-1: “Integrated Services Digital Network (ISDN); Signalling

28、 System No.7 (SS7); ISDN User Part (ISUP); Application transport mechanism; Part 1: Protocol specification ITU-T Recommendation Q.765, modified“. 22 ETSI EN 300 485: “Integrated Services Digital Network (ISDN); Definition and usage of cause and location in Digital Subscriber Signalling System No. on

29、e (DSS1) and Signalling System No. 7 (SS7) ISDN User Part (ISUP) ITU-T Recommendation Q.850 (1998) with addendum modified“. 23 ETSI EN 300 356-2: “Integrated Services Digital Network (ISDN); Signalling System No. 7 (SS7); ISDN User Part (ISUP) version 4 for the international interface; Part 2: ISDN

30、supplementary service ITU-T Recommendation Q.730 (1999) modified“. 24 ETSI EN 300 356-1: “Integrated Services Digital Network (ISDN); Signalling System No.7 (SS7); ISDN User Part (ISUP) version 4 for the international interface; Part 1: Basic services ITU-T Recommendations Q.761 to Q.764 (1999) modi

31、fied“. 25 ETSI EN 302 097: “Integrated Services Digital Network (ISDN); Signalling System No.7 (SS7); ISDN User Part (ISUP); Enhancement for support of Number Portability (NP) ITU-T Recommendation Q.769.1 (2000), modified“. 26 ETSI EN 301 848-1: “Integrated Services Digital Network (ISDN); Signallin

32、g System No.7 (SS7); Bearer Independent Call Control (BICC); Signalling procedures in an ATM/IP/ backbone network; Capability Set 1 (CS1); Part 1: Protocol specification ITU-T Recommendations Q.1901 and Q.765.5, modified“. 27 ETSI EN 300 008-1: “Integrated Services Digital Network (ISDN); Signalling

33、 System No.7; Message Transfer Part (MTP) to support international interconnection; Part 1: Protocol specification ITU-T Recommendations Q.701, Q.702, Q.703, Q.704, Q.705, Q.706, Q.707 and Q.708 modified“. 28 ETSI EN 301 004-1: “Broadband Integrated Services Digital Network (B-ISDN); Signalling Syst

34、em No.7; Message Transfer Part (MTP) level 3 functions and messages to support international interconnection; Part 1: Protocol specification ITU-T Recommendation Q.2210 (1996), modified“. 29 ETSI EN 300 436-1: “Broadband Integrated Services Digital Network (B-ISDN); Signalling ATM Adaptation Layer (

35、SAAL); Service Specific Connection Oriented Protocol (SSCOP); Part 1: Protocol specification ITU-T Recommendation Q.2110, modified“. 30 ETSI EN 301 062-1: “Integrated Services Digital Network (ISDN); Signalling System No.7; Support of Virtual Private Network (VPN) applications with Private network Q

36、 reference point Signalling System number 1 (PSS1) information flows; Part 1: Protocol specification ITU-T Recommendations Q.765.1 and Q.699.1, modified“. 31 ETSI ETS 300 374-1: “Intelligent Network (IN); Intelligent Network Capability Set 1 (CS1); Core Intelligent Network Application Protocol (INAP

37、); Part 1: Protocol specification“. ETSI ETSI EN 302 213 V1.1.2 (2004-01) 7 32 ETSI EN 301 140-1: “Intelligent Network (IN); Intelligent Network Application Protocol (INAP); Capability Set 2 (CS2); Part 1: Protocol specification“. 33 ETSI ETS 300 656: “Broadband Integrated Services Digital Network (

38、B-ISDN); Signalling System No.7; B-ISDN User Part (B-ISUP) Capability Set 1 (CS1); Basic services ITU-T Recommendations Q.2761 to Q.2764 (1995), modified“. 34 ETSI EN 300 403-1: “Integrated Services Digital Network (ISDN); Digital Subscriber Signalling System No. one (DSS1) protocol; Signalling netw

39、ork layer for circuit-mode basic call control; Part 1: Protocol specification ITU-T Recommendation Q.931 (1993), modified“. 35 ETSI EN 300 403-2: “Integrated Services Digital Network (ISDN); Digital Subscriber Signalling System No. one (DSS1) protocol; Signalling network layer for circuit-mode basic

40、 call control; Part 2: Specification and Description Language (SDL) diagrams“. 36 ETSI EN 300 196-1: “Integrated Services Digital Network (ISDN); Generic functional protocol for the support of supplementary services; Digital Subscriber Signalling System No. one (DSS1) protocol; Part 1: Protocol spec

41、ification“. 37 ETSI EN 300 121: “Integrated Services Digital Network (ISDN); Application of the ISDN User Part (ISUP) of ITU-T Signalling System No. 7 (SS7) for international ISDN interconnections (ISUP version 1) Amendment 1: International Emergency Preference Scheme (IEPS) service ITU-T Recommenda

42、tion Q.767 Amendment 1 (2002), modified“. 38 ETSI EN 300 356 (all parts): “Integrated Services Digital Network (ISDN); Signalling System No.7 (SS7); ISDN User Part (ISUP) version 4 for the international interface“. 39 ETSI EN 301 850-1: “Integrated Services Digital Network (ISDN); Signalling System

43、No.7 (SS7); ISDN User Part (ISUP); Application transport mechanism; Support of the generic addressing and transport protocol; Part 1: Protocol specification ITU-T Recommendation Q.765.4, modified)“. 40 ETSI EN 300 899-1: “Integrated Services Digital Network (ISDN); Signalling System No.7; Interworki

44、ng between ISDN User Part (ISUP) version 2 and Digital Subscriber Signalling System No. one (DSS1); Part 1: Protocol specification ITU-T Recommendation Q.699, modified“. 41 ETSI TS 101 341: “Telecommunications and Internet Protocol Harmonization Over Networks (TIPHON); Protocol Implementation Confor

45、mance Statement (PICS) proforma for the support of supplementary services in H.323; Support of H.450.2: Call transfer supplementary services for H.323“. 42 ETSI TS 101 342: “Telecommunications and Internet Protocol Harmonization Over Networks (TIPHON); Protocol Implementation Conformance Statement (

46、PICS) proforma for the support of supplementary services in H.323; Support of H.450.3: Call diversion supplementary services for H.323“. 43 ETSI ETS 300 495: “Broadband Integrated Services Digital Network (B-ISDN); Signalling System No.7; Interworking between Broadband ISDN User Part (B-ISUP) and Di

47、gital Subscriber Signalling System No. two (DSS2) ITU-T Recommendation Q.2650 (1995), modified“. 44 ETSI ETS 300 496: “Broadband Integrated Services Digital Network (B-ISDN); Signalling System No.7; Interworking between Broadband ISDN User Part (B-ISUP) and narrowband ISDN User Part (ISUP) ITU-T Rec

48、ommendation Q.2660 (1995), modified“. 45 ETSI ETS 300 657: “Broadband Integrated Services Digital Network (B-ISDN); Signalling System No.7; B-ISDN User Part (B-ISUP) Capability Set 1 (CS1); Supplementary services ITU-T Recommendation Q.2730 (1995), modified“. 46 ETSI EN 300 443-1: “Broadband Integra

49、ted Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; B-ISDN user-network interface layer 3 specification for basic call/bearer control; Part 1: Protocol specification ITU-T Recommendation Q.2931 (1995), modified“. 47 ETSI ETS 300 796-1: “Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol;