ETSI EN 302 217-2-1-2014 Fixed Radio Systems Characteristics and requirements for point-to-point equipment and antennas Part 2-1 System-dependent requirements for digital systems o_1.pdf

1、 ETSI EN 302 217-2-1 V2.1.1 (2014-12) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied EUROPEAN STANDARD ETSI ETSI EN 302

2、217-2-1 V2.1.1 (2014-12)2Reference REN/ATTM-04017 Keywords DFRS, digital, DRRS, FWA, point-to-point, radio, regulation, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association bu

3、t non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present

4、document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive

5、within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present doc

6、ument, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written p

7、ermission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMan

8、d the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN

9、302 217-2-1 V2.1.1 (2014-12)3Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 9g33.1 Definitions 9g33.2 Symbols 9g33.3 Ab

10、breviations . 9g34 General characteristics . 9g34.1 Frequency bands and channel arrangements 9g34.2 Special compatibility requirements between systems 10g34.3 Transmission capacity and spectral efficiency . 10g35 Main requirements 10g35.1 System nominal loading . 11g35.2 Environmental profile . 11g3

11、5.3 Transmitter characteristics 11g35.3.1 Transmitter power and power tolerance 11g35.3.1.1 Maximum power . 11g35.3.1.2 Transmitter output power tolerance 11g35.3.2 Transmitter power and frequency control . 12g35.3.2.1 Transmitter power control (ATPC and RTPC) . 12g35.3.2.1.1 Automatic Transmitter P

12、ower Control (ATPC) . 12g35.3.2.1.2 Remote Transmitter Power Control (RTPC) . 13g35.3.2.2 Remote Frequency Control (RFC) 13g35.3.3 Radio Frequency (RF) spectrum mask 13g35.3.4 Discrete CW components exceeding the spectrum mask limit . 13g35.3.4.1 Discrete CW components at the symbol rate 13g35.3.4.2

13、 Other discrete CW components exceeding the spectrum mask limit 13g35.3.5 Spurious emissions - external . 13g35.3.6 Radio frequency tolerance 13g35.4 Receiver characteristics 14g35.4.1 Spurious emissions-external . 14g35.5 System performance without diversity . 14g35.5.1 BER as a function of receive

14、r signal level 14g35.5.2 Interference sensitivity 14g35.5.2.1 Co-channel “external“ interference sensitivity 14g35.5.2.2 Adjacent channel interference sensitivity 14g35.5.2.3 CW spurious interference 14g36 Complementary requirements 15g36.1 Branching/feeder requirements 15g36.1.1 Waveguide flanges (

15、or other connectors) . 15g36.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C reference point) 16g36.2 Intermodulation products . 16g36.3 Transmitter characteristics 17g36.3.1 Spurious emissions - internal 17g36.3.2 Radio Frequency (RF) spectrum mask when mixed supplier compa

16、tibility is required . 17g36.4 Receiver characteristics 18g36.4.1 Maximum input level and input level range . 18g36.4.2 Spurious emissions - internal 19g3ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)46.4.3 Image rejection . 19g36.4.4 Innermost channel selectivity . 20g36.5 System performance without div

17、ersity . 20g36.5.1 Equipment Residual BER (RBER) . 20g36.5.2 Distortion sensitivity . 22g36.5.2.1 Introduction . 22g36.5.2.2 Requirement 22g36.5.2.3 Assessment 23g36.5.3 Interference sensitivity for CCDP with XPIC operation . 24g36.5.3.1 General 24g36.5.3.2 Co-channel “internal“ interference sensiti

18、vity in flat fading conditions 24g36.6 System characteristics with diversity . 24g36.6.1 Differential delay compensation . 24g36.6.2 BER performance . 24g3Annex A (normative): Spectrum masks and receiver selectivity when mixed supplier compatibility is required . 25g3A.0 Introduction 25g3A.1 TX mask

19、s assessment . 26g3A.2 Normal channels - Emission mask floor 26g3A.2.1 RBER impact 26g3A.2.2 Local TX to RX compatibility 26g3A.2.2.1 Spectrum mask 26g3A.2.2.2 Receiver selectivity . 27g3A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel separation of 28 M

20、Hz to 30 MHz . 27g3A.3.1 Innermost channels spectrum masks 27g3A.3.2 Receiver innermost channel selectivity 29g3A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel separation of 40 MHz . 30g3A.4.1 Innermost channels spectrum masks 30g3A.4.2 Receiver innermost chan

21、nels selectivity . 31g3A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz 32g3A.5.1 Innermost channels spectrum masks 32g3A.5.2 Receiver innermost channels selectivity . 33g3Annexes B to E: Deleted and left void 35g3Annex F (normative): Definition of equivalent

22、data rates for packet data, PDH/SDH and other signals on the traffic interface. 36g3Annex G (informative): Additional information 37g3G.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 37g3G.2 Measurement test set for XPI characteristics . 38g3G.3 Differential delay compensa

23、tion range . 39g3G.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 40g3G.4.1 FER/BER equivalence 40g3G.4.2 FER equipment settings and measurement techniques (example) 41g3G.5 Automatic Transmitter Power Control (ATPC) . 41g3Annex H (informative): Mitigation techn

24、iques referred in ERC/DEC(00)07 (18 GHz band) . 43g3Annex I (informative): Change History 44g3History 45g3ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)5Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining

25、to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat.

26、Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI

27、 Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 2-1 of a multi-part deliverable covering the F

28、ixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 15. National transposition dates Date of adoption of this EN: 5 December 2014 Date of latest announcement of this EN (doa): 31 March 2015 Date of l

29、atest publication of new National Standard or endorsement of this EN (dop/e): 30 September 2015 Date of withdrawal of any conflicting National Standard (dow): 30 September 2015 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “may not“, “need“, “ne

30、ed not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The introduction o

31、f EN 302 217-1 15 applies. ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)61 Scope The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced in

32、 two different clauses sub-sets: Main requirements are requirements that are also related to the “essential requirements“ under article 3.2 of the R antenna system requirements are covered in EN 302 217-4-1 i.9 and EN 302 217-4-2 i.10. The present document does not cover test procedures and test con

33、ditions which are set out in EN 301 126-1 14. As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, equipment are subdivided in different spectral efficiency classes as defined in EN 302 217-2-2 16. The spectral efficiency classes are indicative only and do not

34、 imply any constraint to the actual modulation format, provided that all the requirements in the relevant parts of this Multi-part deliverable for the declared class are met. Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R Environmental co

35、nditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction“. 5 ETSI EN 300 019-1-1: “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-1: Classification

36、of environmental conditions; Storage“. 6 ETSI EN 300 019-1-2: “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-2: Classification of environmental conditions; Transportation“. 7 ETSI EN 300 019-1-3: “Environmental Engineering (

37、EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of environmental conditions; Stationary use at weatherprotected locations“. 8 ETSI EN 300 019-1-4: “Environmental Engineering (EE); Environmental conditions and environmental tests for te

38、lecommunications equipment; Part 1-4: Classification of environmental conditions; Stationary use at non-weatherprotected locations“. 9 ETSI EN 300 019-2-0: “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-0: Specification of e

39、nvironmental tests; Introduction“. 10 ETSI EN 300 019-2-1: “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-1: Specification of environmental tests; Storage“. 11 ETSI EN 300 019-2-2: “Environmental Engineering (EE); Environmen

40、tal conditions and environmental tests for telecommunications equipment; Part 2-2: Specification of environmental tests; Transportation“. 12 ETSI EN 300 019-2-3: “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-3: Specificatio

41、n of environmental tests; Stationary use at weatherprotected locations“. 13 ETSI EN 300 019-2-4: “Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of environmental tests; Stationary use at non-weatherprotected

42、locations“. 14 ETSI EN 301 126-1: “Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point equipment - Definitions, general requirements and test procedures“. 15 ETSI EN 302 217-1: “Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Over

43、view and system-independent common characteristics“. 16 ETSI EN 302 217-2-2: “Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-2: Digital systems operating in frequency bands where frequency co-ordination is applied; Harmonized EN covering the e

44、ssential requirements of Article 3.2 of the R Generic wordings for standards on DFRS (Digital Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment parameters“. i.6 ETSI TR 101 506: “Fixed Radio Systems; Generic definitions, terminology and applicability of essen

45、tial requirements under the article 3.2 of 1999/05/EC Directive to Fixed Radio Systems“. i.7 ETSI TR 102 243-1: “Fixed Radio Systems; Representative values for transmitter power and antenna gain to support inter- and intra-compatibility and sharing analysis; Part 1: Digital point-to-point systems“.

46、i.8 ETSI TR 103 103: “Fixed Radio Systems; Point-to-point systems; ATPC, RTPC, Adaptive Modulation (mixed-mode) and Bandwidth Adaptive functionalities; Technical background and impact on deployment, link design and coordination“. ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)9i.9 ETSI EN 302 217-4-1: “Fi

47、xed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4-1: System-dependent requirements for antennas“. i.10 ETSI EN 302 217-4-2: “Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4-2: Antennas; Harmon

48、ized EN covering the essential requirements of article 3.2 of the R Point-to-point equipment; Derivation of receiver interference parameters useful for planning fixed service point-to-point systems operating different equipment classes and/or capacities“. i.12 Recommendation ITU-R F.383-9: “Radio-fr

49、equency channel arrangements for high capacity fixed wireless systems operating in the lower 6 GHz (5 925 to 6 425 MHz) band“. i.13 Recommendation ITU-R F.384-11: “Radio -frequency channel arrangements for medium- and high-capacity digital fixed wireless systems operating in the 6 425-7 125 MHz band“. i.14 Recommendation ITU-R F.385-10: “Radio-frequency channel arrangements for fixed wireless systems operating in the 7 110-7 900 MHz band“. i.15 Recommendation ITU-R F.595-10: “Radio-frequency channel arrangements for fixe