ETSI EN 302 217-2-2017 Fixed Radio Systems Characteristics and requirements for point-to-point equipment and antennas Part 2 Digital systems operating in frequency bands from 1 GHz.pdf

1、 ETSI EN 302 217-2 V3.1.1 (2017-05) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/

2、EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 217-2 V3.1.1 (2017-05) 2 Reference REN/ATTM-0431 Keywords antenna, DFRS, digital, DRRS, FWA, point-to-point, radio, regulation, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 4

3、7 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in

4、print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of th

5、e Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:

6、/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, elec

7、tronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Tel

8、ecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM

9、 and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 217-2 V3.1.1 (2017-05) 3 Contents Intellectual Property Rights 9g3Foreword . 9g3Modal verbs terminology 9g3Introduction 9g31 Scope 10g32 References 10g32.1 Normative references . 10g32.2 Informative refer

10、ences 10g33 Definitions, symbols and abbreviations . 14g33.1 Definitions 14g33.2 Symbols 14g33.3 Abbreviations . 14g34 Technical requirements specifications . 14g34.1 General requirements . 14g34.1.1 Requirements framework 14g34.1.1.1 Introduction and equipment flexibility 14g34.1.1.2 Operating freq

11、uency bands 15g34.1.1.3 Spectral efficiency classes . 16g34.1.1.4 System alternatives 16g34.1.1.5 Channel arrangements and utilization . 17g34.1.1.6 Specific Requirements for frequency bands 17g34.1.2 Minimum RIC density 19g34.1.3 Payload flexibility . 19g34.1.4 System identification and traffic loa

12、ding 20g34.1.5 Environmental profile . 21g34.2 Transmitter requirements . 21g34.2.0 General: system loading 21g34.2.1 Transmitter power and power tolerance 22g34.2.1.1 Maximum power and EIRP . 22g34.2.1.2 Combined TX power output and EIRP limits . 22g34.2.1.3 Output power tolerance . 22g34.2.2 Trans

13、mitter power and frequency control . 23g34.2.2.1 Power Control (ATPC and RTPC) 23g34.2.2.1.0 General background . 23g34.2.2.1.1 Automatic Transmit Power Control (ATPC) . 23g34.2.2.1.2 Remote Transmit Power Control (RTPC) . 23g34.2.2.2 Remote Frequency Control (RFC) 23g34.2.3 Radio Frequency (RF) spe

14、ctrum mask 23g34.2.3.1 Limits background 23g34.2.3.2 Limits 26g34.2.4 Discrete CW components exceeding the spectrum mask limit . 39g34.2.4.1 Discrete CW components at the symbol rate 39g34.2.4.2 Other discrete CW components exceeding the spectrum mask limit 39g34.2.5 Unwanted emissions in the spurio

15、us domain - external 40g34.2.6 Dynamic Change of Modulation Order 41g34.2.7 Radio frequency tolerance 41g34.2.8 Emission limitations outside the allocated band . 42g34.3 Receiver requirements 42g34.3.0 General: System loading . 42g34.3.1 Unwanted emissions in the spurious domain - external 42g34.3.2

16、 BER as a function of receiver input signal level RSL 42g34.3.3 Receiver selectivity . 43g34.3.3.1 Introduction . 43g34.3.3.2 Co-channel “external“, first and second adjacent channel interference sensitivity . 43g3ETSI ETSI EN 302 217-2 V3.1.1 (2017-05) 4 4.3.3.2.1 Requirements basics 43g34.3.3.2.2

17、Limits for co-channel and first adjacent channel . 44g34.3.3.2.3 Limits for second adjacent channel interference . 44g34.3.3.3 CW spurious interference (blocking Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. La

18、test updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI

19、 Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document has been prepared under the Commissions sta

20、ndardisation request C(2015) 5376 final i.63 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.

21、1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the correspondi

22、ng essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable covering Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas. Full details of the entire series can be found in ETSI EN

23、 302 217-1 4. National transposition dates Date of adoption of this EN: 27 March 2017 Date of latest announcement of this EN (doa): 30 June 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 December 2017 Date of withdrawal of any conflicting National Stan

24、dard (dow): 31 December 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisi

25、ons). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The ETSI EN 302 217 series has been produced in order to rationalize a large number of previous ETSI ENs dealing with equipment and antennas for Point-to-Point (P-P) Fixed Service appli

26、cations. For more details, see foreword in ETSI EN 302 217-1 4. ETSI ETSI EN 302 217-2 V3.1.1 (2017-05) 10 1 Scope The present document specifies technical characteristics and methods of measurements for Point-to-point (P-P) Digital Fixed Radio Systems (DFRS) operating in frequency bands allocated t

27、o Fixed Service (FS) from 1 GHz to 86 GHz, corresponding to the appropriate frequency bands from 1,4 GHz to 86 GHz as described in annex B to annex J. Systems in the scope of the present document are generally intended to operate in full frequency division duplex (FDD) and covers also unidirectional

28、 applications. Time division duplex (TDD) applications, when possibly applicable in a specific band, are explicitly mentioned as appropriate in annex B through annex J. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.1 under the conditions identified i

29、n annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docb

30、ox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 126-1 (V1.1.2) (09-1999): “Fixe

31、d Radio Systems; Conformance testing; Part 1: Point-to-point equipment - Definitions, general requirements and test procedures“. 2 ETSI EN 301 126-3-1 (V1.1.2) (12-2002): “Fixed Radio Systems; Conformance testing; Part 3-1: Point-to-Point antennas; Definitions, general requirements and test procedur

32、es“. 3 ETSI EN 301 390 (V1.3.1) (08-2013): “Fixed Radio Systems; Point-to-point and Multipoint Systems; Unwanted emissions in the spurious domain and receiver immunity limits at equipment/antenna port of Digital Fixed Radio Systems“. 4 ETSI EN 302 217-1 (V3.1.1) (05-2017): “Fixed Radio Systems; Char

33、acteristics and requirements for point-to-point equipment and antennas; Part 1: Overview, common characteristics and system-independent requirements“. 5 ETSI EN 302 217-4 (V2.1.1) (05-2017): “Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 4: Ant

34、ennas“. 6 Void. 7 ITU Radio Regulations (2016). 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest vers

35、ion of the reference document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document

36、 but they assist the user with regard to a particular subject area. ETSI ETSI EN 302 217-2 V3.1.1 (2017-05) 11 i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market

37、of radio equipment and repealing Directive 1999/5/EC. i.2 ETSI EG 203 336 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53

38、/EU“. i.3 CEPT/ERC/REC 74-01 (Cardiff 2011): “Unwanted emissions in the spurious domain“. i.4 CEPT/ERC/REC(01)02 (2010): “Preferred channel arrangement for digital fixed service systems operating in the frequency band 31.8 - 33.4 GHz“. i.5 CEPT/ERC/REC 12-02 (2007): “Harmonized radio frequency chann

39、el arrangements for analogue and digital terrestrial fixed systems operating in the band 12.75 GHz to 13.25 GHz“. i.6 CEPT/ERC/REC 12-03: “Harmonized radio frequency channel arrangements for digital terrestrial fixed systems operating in the band 17.7 GHz to 19.7 GHz“. i.7 CEPT/ERC/REC 12-05 (2007):

40、 “Harmonized radio frequency channel arrangements for digital terrestrial fixed systems operating in the band 10.0 - 10.68 GHz“. i.8 CEPT/ERC/REC 12-06 (2010): “Harmonized radio frequency channel arrangements for digital terrestrial fixed systems operating in the band 10.7 GHz to 11.7 GHz“. i.9 CEPT

41、/ERC/REC 12-07: “Harmonized radio frequency channel arrangements for digital terrestrial fixed systems operating in the band 14.5 - 14.62 GHz paired with 15.23 - 15.35 GHz“. i.10 CEPT/ERC/REC 12-08: “Harmonized radio frequency channel arrangements and block allocations for low, medium and high capac

42、ity systems in the band 3600 MHz to 4200 MHz“. i.11 CEPT/ERC/REC 12-11 (2015): “Radio frequency channel arrangement for fixed service systems operating in the bands 48.5-50.2 GHz and 50.9-52.6 GHz“. i.12 CEPT/ERC/REC 12-12 (2015): “Radio frequency channel arrangement for fixed service systems operat

43、ing in the band 55.78-57.0 GHz“. i.13 CEPT/ERC/REC 14-01 (2014): “Radio-frequency channel arrangements for high capacity analogue and digital radio-relay systems operating in the band 5925 MHz - 6425 MHz“. i.14 CEPT/ERC/REC 14-02 (2014): “Radio-frequency channel arrangements for medium and high capa

44、city analogue or high capacity digital radio-relay systems operating in the band 6425 MHz - 7125 MHz“. i.15 CEPT/ERC/REC 14-03: “Harmonized radio frequency channel arrangements for low and medium capacity systems in the band 3400 MHz to 3600 MHz“. i.16 CEPT/ERC/REC T/R 12-01 (2010): “Preferred chann

45、el arrangements for fixed service systems operating in the band 37-39.5 GHz“. i.17 CEPT/ERC/REC T/R 13-01 (2010): “Preferred channel arrangements for fixed services systems operating in the frequency range 1-2.3 GHz“. i.18 CEPT/ERC/REC T/R 13-02 (2010): “Preferred channel arrangements for fixed serv

46、ices systems in the frequency range 22.0 - 29.5 GHz“. i.19 CEPT ECC/REC(01)04 (2014): “Recommended guidelines for the accommodation and assignment of Fixed Multimedia Wireless Systems (MWS) and Point-to-point (P-P) Fixed Wireless Systems in the frequency band 40.5-43.5 GHz“. i.20 Void. i.21 CEPT ECC

47、/REC(02)02 (2010): “Channel arrangement for digital fixed service systems (point-to-point and point-to-multipoint) operating in the frequency band 31 - 31.3 GHz“. ETSI ETSI EN 302 217-2 V3.1.1 (2017-05) 12 i.22 CEPT ECC/REC (02)06 (2011): “Preferred channel arrangements for digital fixed service sys

48、tems operating in the frequency range 7125-8500 MHz“. i.23 CEPT ECC/REC (05)02 (2009): “Use of the 64 - 66 GHz frequency band for Fixed Service“. i.24 CEPT ECC/REC(05)07 (2013): “Radio frequency channel arrangements for fixed service systems operating in the bands 71-76 GHz and 81-86 GHz“. i.25 CEPT

49、 ECC/REC(09)01: “Use of the 57 - 64 GHz frequency band for point-to-point Fixed Wireless Systems“. i.26 CEPT ECC/REC(14)06 (2015): “Implementation of Fixed Service Point-to-Point narrow channels (3.5 MHz, 1.75 MHz, 0.5 MHz, 0.25 MHz, 0.025 MHz) in the guard bands and centre gaps of the lower 6 GHz (5925 to 6425 MHz) and upper 6 GHz (6425 to 7125 MHz) bands“. i.27 IEEE 802.3-2012: “IEEE Standard for Ethernet“. i.28 ETSI TR 100 028 (all parts): “Electromagnetic compatibility and Radio spectrum Mat