ETSI EN 302 264-1-2009 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices Road Transport and Traffic Telematics (RTTT) Short Range Radar equipment o.pdf

1、 ETSI EN 302 264-1 V1.1.1 (2009-06)European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Short Range Devices;Road Transport and Traffic Telematics (RTTT);Short Range Radar equipment operatingin the 77 GHz to 81 GHz band;Part 1: Technical requirem

2、ents and methods of measurementETSI ETSI EN 302 264-1 V1.1.1 (2009-06) 2Reference DEN/ERM-TG31B-001-1 Keywords radar, radio, RTTT, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742

3、C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existi

4、ng or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present docume

5、nt should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the follow

6、ing services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2009. All rights

7、 reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE is a Trade Mark of ETSI current

8、ly being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 264-1 V1.1.1 (2009-06) 3Contents Intellectual Property Rights 5g3Foreword . 5g31 Scope 6g32 References 6g32.1

9、 Normative references . 6g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 8g33.3 Abbreviations . 9g34 Technical requirements specifications . 10g34.1 Presentation of equipment for testing purposes 10g34.1.1 Choice of model for testing 10g34

10、.2 Mechanical and electrical design 10g34.3 Auxiliary test equipment 10g35 Test conditions, power sources and ambient temperatures 11g35.1 Normal and extreme test conditions . 11g35.2 External test power source 11g35.3 Normal test conditions 11g35.3.1 Normal temperature and humidity 11g35.3.2 Normal

11、 test power source . 11g35.3.2.1 Mains voltage 11g35.3.2.2 Other power sources 11g35.4 Extreme test conditions 12g35.4.1 Extreme temperatures . 12g35.4.1.1 Procedure for tests at extreme temperatures 12g35.4.1.2 Extreme temperature ranges 12g35.4.2 Extreme test source voltages . 12g35.4.2.1 Mains vo

12、ltage 12g35.4.2.2 Other power sources 12g36 General conditions 12g36.1 Test fixture . 13g36.1.1 Requirements 13g36.1.2 Calibration 13g36.1.3 General requirements for RF cables and waveguides . 14g36.1.4 Shielded anechoic chamber. 15g37 Methods of measurement and limits for transmitter parameters 16g

13、37.1 Methods of measurement and limits for transmitters in 77 GHz to 81 GHz band 16g37.1.1 Permitted range of operating frequencies . 16g37.1.1.1 Definition 16g37.1.1.2 Method of measurement 16g37.1.1.3 Limits 17g37.1.2 Maximum radiated average power spectral density (e.i.r.p.) 17g37.1.2.1 Definitio

14、n 17g37.1.2.2 Method of measurement 17g37.1.2.3 Limits 18g37.1.3 Maximum radiated peak power (e.i.r.p.) . 18g37.1.3.1 Definition 18g37.1.3.2 Method of measurement 18g37.1.3.3 Limits 19g37.2 Maximum radiated spurious and out-of-band emissions 19g37.2.1 Definition 19g37.2.2 Measuring receiver . 19g3ET

15、SI ETSI EN 302 264-1 V1.1.1 (2009-06) 47.2.3 Method of measurement for radiated spurious or out-of-band emissions . 20g37.2.4 Limits 20g38 Methods of measurement and limits for receiver parameters . 21g38.1 Receiver spurious emissions. 21g38.1.1 Definition 21g38.1.2 Method of measurement - radiated

16、spurious emissions 21g38.1.3 Limit . 21g39 Interpretation of measurement results 22g39.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 22g39.2 Measurement uncertainty is greater than maximum acceptable uncertainty 23g3Annex A (normative): Radiated measurements 24g

17、3A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 24g3A.2 Guidance on the use of radiation test sites . 24g3A.2.1 Substitution antenna . 24g3A.3 Indoor test site using a fully anechoic RF chamber . 24g3A.3.1 Example of the construction of a shielded ane

18、choic chamber 25g3A.3.2 Influence of parasitic reflections in anechoic chambers . 26g3A.3.3 Calibration of the shielded RF anechoic chamber 27g3Annex B (normative): General description of measurement methods 28g3B.1 Radiated measurements 28g3Annex C (informative): Example of modulation schemes. 29g3

19、C.1 Pseudo Noise Pulse Position Modulation (PN PPM) . 29g3C.1.1 Definition . 29g3C.1.2 Typical operation parameters . 30g3C.2 Pulsed FH (Pulsed Frequency hopping) . 30g3C.2.1 Definition . 30g3C.2.2 Typical operation parameters . 31g3C.2.3 Additional requirements for pulsed FH equipment measurement 3

20、1g3C.2.3.1 Pulsed FH modulation 31g3C.2.3.2 Measurement requirements . 31g3C.3 PN-ASK (Pseudo noise coded amplitude shift keying) . 32g3C.3.1 Definition . 32g3C.3.2 Typical operation parameters . 33g3C.4 PN-PSK (Pseudo noise coded phase shift keying) . 33g3C.4.1 Definition . 33g3C.4.2 Typical operat

21、ion parameters . 34g3C.5 Frequency modulated continuous wave . 34g3C.5.1 Definition . 34g3C.5.2 Typical operating parameters . 35g3C.6 Combination of modulation types 35g3Annex D (normative): Installation requirements of 79 GHz Short Range Radar (SRR) systems 36g3Annex E (informative): Conversion of

22、 power spectral density to e.i.r.p. 37g3E.1 Assumptions . 37g3E.2 Example 37g3Annex F (informative): Bibliography . 38g3History 39 ETSI ETSI EN 302 264-1 V1.1.1 (2009-06) 5Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The

23、 information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available fro

24、m the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETS

25、I SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). For n

26、on EU countries the present document may be used for regulatory (Type Approval) purposes. Equipment compliant with the present document is intended for fitment into road vehicles, therefore it is subject to automotive EMC type approval and has to comply with Commission Directive 2004/104/EC i.4. For

27、 use on vehicles outside the scope of Commission Directive 2004/104/EC i.4 compliance with an EMC directive/standard appropriate for that use is required. The present document is part 1 of a multi-part deliverable covering Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range D

28、evices; Road Transport and Traffic Telematics (RTTT); Short Range Radar equipment operating in the 77 GHz to 81 GHz band, as identified below: Part 1: “Technical requirements and methods of measurement“; Part 2: “Harmonized EN covering the essential requirements of article 3.2 of the R b) receivers

29、operating in the 79 GHz range; c) integrated transceivers in the 79 GHz range. The present document: contains the technical characteristics and test methods for short range radar equipment fitted with integral antennas operating in the 79 GHz range; covers short range radar vehicle applications in t

30、he 79 GHz range. It covers integrated transceivers and separate transmit/receive modules. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. Non-specific

31、 reference may be made only to a complete document or a part thereof and only in the following cases: - if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which

32、 are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenc

33、ed documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. 1 CISPR 16 (2006) (parts 1-1, 1-4 and 1-5): “Specification

34、for radio disturbance and immunity measuring apparatus and methods; Part 1: Radio disturbance and immunity measuring apparatus“. ETSI ETSI EN 302 264-1 V1.1.1 (2009-06) 72 ETSI TR 102 273 (all parts - V1.2.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated M

35、ethods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber“. 3 ETSI TR 100 028 (V1.4.1) (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment charac

36、teristics“. 2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) appl

37、ies. i.1 ECC decision ECC/DEC/(04)03 of 19 March 2004 on the frequency band 77 - 81 GHz to be designated for the use of Automotive Short Range Radars. i.2 EC decision 2004/545/EC of 8 July 2004 on the harmonization of radio spectrum in the 79 GHz range for the use of automotive short-range radar equ

38、ipment in the Community. i.3 Radio Regulations: “International Telecommunication Union, Edition of 2004“. i.4 Commission Directive 2004/104/EC of 14 October 2004 adapting to technical progress Council Directive 72/245/EEC relating to the radio interference (electromagnetic compatibility) of vehicles

39、 and amending Directive 70/156/EEC on the approximation of the laws of the Member States relating to the type-approval of motor vehicles and their trailers. i.5 ETSI EN 302 264-2: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices; Road Transport and Traffic Telemat

40、ics (RTTT); Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R relative humidity 20 % to 75 %. When it is impracticable to carry out tests under these conditions, a note to this effect, stating the amb

41、ient temperature and relative humidity during the tests, shall be added to the test report. 5.3.2 Normal test power source The internal impedance of the test power source shall be low enough for its effect on the test results to be negligible. For the purpose of the tests, the voltage of the externa

42、l test power source shall be measured at the input terminals of the equipment. 5.3.2.1 Mains voltage The normal test voltage for equipment shall be the nominal mains voltage. For the purpose of the present document, the nominal voltage shall be the declared voltage, or any of the declared voltages,

43、for which the equipment was designed. The frequency of the test power source corresponding to the ac mains shall be between 49 Hz and 51 Hz. 5.3.2.2 Other power sources For operation from other power sources the normal test voltage shall be that declared by the provider. Such values shall be stated

44、in the test report. ETSI ETSI EN 302 264-1 V1.1.1 (2009-06) 125.4 Extreme test conditions 5.4.1 Extreme temperatures 5.4.1.1 Procedure for tests at extreme temperatures Before measurements are made, the equipment shall have reached thermal balance in the test chamber. The equipment shall not be swit

45、ched off during the temperature stabilizing period. If the thermal balance is not checked by measurements, a temperature stabilizing period of at least one hour, or such period as may be decided by the accredited test laboratory, shall be allowed. The sequence of measurements shall be chosen, and th

46、e humidity content in the test chamber shall be controlled so that excessive condensation does not occur. 5.4.1.2 Extreme temperature ranges For tests at extreme temperatures, measurements shall be made in accordance with the procedures specified in clause 5.4.1.1, at the upper and lower temperature

47、s of one of the following limits: temperature: -20 C to +55 C. 5.4.2 Extreme test source voltages 5.4.2.1 Mains voltage The extreme test voltages for equipment to be connected to an ac mains source shall be the nominal mains voltage 10 %. 5.4.2.2 Other power sources For equipment using other power s

48、ources, or capable of being operated from a variety of power sources, the extreme test voltages shall be that declared by the provider. These shall be recorded in the test report. 6 General conditions Detailed descriptions of the radiated measurement arrangements are included in annexes A and B. In

49、general, measurements shall be carried out under far field conditions. The far field condition for the EUTs is considered to be fulfilled in a minimum radial distance “X“ that shall be a minimum of 2d2/ , where d is the largest dimension of the antenna aperture of the EUT, for a single device measurement. Absolute power measurements shall be made using an appropriate method to ensure that the wave front is properly formed (i.e. operating in far field conditions). The test site shall meet the appropriate requirements as defined in published