ETSI EN 302 340-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for satellite Earth Stations on board Vessels (ESVs) operating in the 11 12 14 GHz frequency ban.pdf

1、 ETSI EN 302 340 V2.1.1 (2016-05) Satellite Earth Stations and Systems (SES); Harmonised Standard for satellite Earth Stations on board Vessels (ESVs) operating in the 11/12/14 GHz frequency bands allocated to the Fixed Satellite Service (FSS) covering the essential requirements of article 3.2 of th

2、e Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 340 V2.1.1 (2016-05) 2 Reference REN/SES-00393 Keywords earth station, ESV, maritime, regulation, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N

3、348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The co

4、ntent of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Do

5、cument Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.

6、org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mec

7、hanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunicatio

8、ns Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM

9、logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 340 V2.1.1 (2016-05) 3 Contents Intellectual Property Rights 7g3Foreword . 7g3Modal verbs terminology 7g3Introduction 7g31 Scope 9g32 References 10g32.1 Normative references . 10g32.2 Informative references 10g33 Defi

10、nitions, symbols and abbreviations . 11g33.1 Definitions 11g33.2 Symbols 13g33.3 Abbreviations . 13g34 Technical requirements specifications . 14g34.1 General . 14g34.1.1 Environmental profile . 14g34.1.2 Operational configurations . 14g34.1.3 ESV states and radio states . 14g34.2 Conformance requir

11、ements 15g34.2.1 Off-axis spurious radiation . 15g34.2.1.1 Justification . 15g34.2.1.2 Specification 16g34.2.1.3 Conformance tests . 17g34.2.2 On-axis spurious radiation for ESV 17g34.2.2.1 Justification . 17g34.2.2.2 Specification 17g34.2.2.2.1 “Carrier-on“ radio state 17g34.2.2.2.2 “Carrier-off“ a

12、nd “Emissions disabled“ radio states 18g34.2.2.3 Conformance tests . 18g34.2.3 Maximum ESV emissions towards the horizon 18g34.2.3.1 Justification . 18g34.2.3.2 Specification 18g34.2.3.2.1 Specification 1: Maximum e.i.r.p. spectral density towards the horizon . 18g34.2.3.2.2 Specification 2: Maximum

13、 e.i.r.p. towards the horizon . 18g34.2.3.3 Conformance tests . 18g34.2.4 Off-axis e.i.r.p. emission density within the band . 18g34.2.4.0 General 18g34.2.4.1 Justification . 18g34.2.4.2 Specification 19g34.2.4.3 Conformance tests . 20g34.2.5 Carrier suppression . 20g34.2.5.1 Justification . 20g34.2

14、.5.2 Specification 20g34.2.5.3 Conformance tests . 21g34.2.6 Antenna pointing and polarization alignment for ESVs . 21g34.2.6.1 Justification . 21g34.2.6.2 Specification 21g34.2.6.3 Conformance tests . 22g34.2.7 Cessation of emissions of the ESV . 22g34.2.7.1 Justification . 22g34.2.7.2 Specificatio

15、n 22g34.2.7.2.1 Specification 1: Mode of cessation of emissions . 22g34.2.7.2.2 Specification 2: Conditions under which the ESV shall cease emissions 22g34.2.7.2.3 Specification 3: Cessation of emissions 23g34.2.7.2.4 Specification 4: Fault conditions . 23g3ETSI ETSI EN 302 340 V2.1.1 (2016-05) 4 4.

16、2.7.3 Conformance tests . 23g34.2.8 Identification of ESV 23g34.2.8.1 Justification . 23g34.2.8.2 Specification 23g34.2.8.3 Conformance tests . 23g34.2.9 Control and Monitoring Functions (CMFs) 24g34.2.9.1 CMF state diagram 24g34.2.9.2 Processor monitoring 25g34.2.9.2.1 Justification . 25g34.2.9.2.2

17、 Specification 25g34.2.9.2.3 Conformance tests . 25g34.2.9.3 Transmit subsystem monitoring 25g34.2.9.3.1 Justification . 25g34.2.9.3.2 Specification 25g34.2.9.3.3 Conformance tests . 25g34.2.9.4 Power-on/Reset . 25g34.2.9.4.1 Justification . 25g34.2.9.4.2 Specification 25g34.2.9.4.3 Conformance test

18、s . 25g34.2.9.5 Control Channel (CC) and Response Channel (RC) . 26g34.2.9.5.1 Justification . 26g34.2.9.5.2 Specification 26g34.2.9.5.3 Conformance tests . 26g34.2.9.6 Network control commands 27g34.2.9.6.1 Justification . 27g34.2.9.6.2 Specification 27g34.2.9.6.3 Conformance test . 27g34.2.9.7 Ini

19、tial burst transmission . 27g34.2.9.7.1 Justification . 27g34.2.9.7.2 Specification 27g34.2.9.7.3 Conformance tests . 28g34.2.10 Receive antenna off-axis gain pattern . 28g34.2.10.1 Justification . 28g34.2.10.2 Specification 28g34.2.10.3 Conformance tests . 28g34.2.11 Blocking performance . 28g34.2.

20、11.1 Justification . 28g34.2.11.2 Specification 28g34.2.11.3 Conformance tests . 29g34.2.12 Adjacent Signal Selectivity . 29g34.2.12.1 Justification . 29g34.2.12.2 Specification 29g34.2.12.3 Conformance tests . 29g35 Testing for compliance with technical requirements 29g35.1 Environmental conditions

21、 for testing . 29g35.2 Essential radio test suites 30g36 Test methods for the complete ESV . 30g36.1 General . 30g36.2 Off-axis spurious radiation . 31g36.2.0 General 31g36.2.1 Test method 31g36.2.1.a General 31g36.2.1.0 Multi-carrier operation 31g36.2.1.1 Up to 2 000 MHz 32g36.2.1.1.1 Test site 32g

22、36.2.1.1.2 Procedure . 32g36.2.1.2 Above 2 000 MHz . 32g36.2.1.2.0 General 32g36.2.1.2.1 Identification of the significant frequencies of spurious radiation 33g36.2.1.2.2 Measurement of radiated power levels of identified spurious radiation 33g3ETSI ETSI EN 302 340 V2.1.1 (2016-05) 5 6.2.1.2.3 Measu

23、rement of conducted spurious radiation at the antenna flange 35g36.3 On-axis spurious radiation 35g36.3.1 Test method 35g36.3.1.1 Test site . 35g36.3.1.2 Method of measurement 36g36.3.1.2.1 General 36g36.3.1.2.2 Method of measurement at the antenna flange 36g36.3.1.2.3 Method of measurement with a t

24、est antenna . 37g36.4 Maximum ESV emissions towards the horizon 38g36.4.1 Test method 38g36.4.1.1 Maximum e.i.r.p. towards the horizon 38g36.4.1.2 Maximum e.i.r.p. spectral density towards the horizon. 38g36.5 Off-axis e.i.r.p. emission density within the band 38g36.5.0 General 38g36.5.1 Test method

25、 39g36.5.1.1 General 39g36.5.1.2 Transmit output power density 39g36.5.1.2.1 General 39g36.5.1.2.2 Test site 39g36.5.1.2.3 Method of measurement 39g36.5.1.3 Antenna transmit gain . 40g36.5.1.3.1 General 40g36.5.1.3.2 Test site 40g36.5.1.3.3 Method of measurement 41g36.5.1.4 Antenna transmit radiatio

26、n patterns 42g36.5.1.4.1 General 42g36.5.1.4.2 Test site 42g36.5.1.4.3 Test arrangement . 42g36.5.1.4.4 Co-polar radiation pattern-azimuth 42g36.5.1.4.5 Co-polar radiation pattern-elevation 43g36.5.1.4.6 Cross-polar radiation pattern-azimuth . 43g36.5.1.4.7 Cross-polar radiation pattern-elevation .

27、44g36.5.2 Computation of results 44g36.6 Carrier suppression . 45g36.6.1 Test method 45g36.7 Antenna pointing for ESV 45g36.7.1 General 45g36.7.2 Test method 45g36.8 Antenna mechanical stability . 46g36.8.1 Test method 46g36.9 Polarization angle alignment capability . 46g36.9.1 Test method 46g36.10

28、Cessation of emissions of the ESV . 47g36.10.1 Test arrangement 47g36.10.2 Test Method 48g36.10.2.1 Required documentation . 48g36.10.2.2 Cessation of emissions from the “Transmission enabled“ state 48g36.10.2.3 Cessation of emission from the “Transmission disabled“ state . 48g36.10.2.4 Cessation of

29、 emission from the “Initial Phase“ state . 48g36.10.2.4.1 EUTs transmitting initial bursts . 48g36.10.2.4.2 EUTs not transmitting initial bursts . 49g36.10.2.5 “Single action“ means of cessation of emissions. 49g36.10.2.6 Fault conditions. 50g36.11 Identification of ESV 50g36.11.1 Test arrangement 5

30、0g36.11.2 Test method 50g36.12 Control and monitoring functions 50g36.12.0 General 50g36.12.1 Test arrangement 50g36.12.2 Processor monitoring- Test method 50g36.12.3 Transmit subsystem monitoring-Test method . 51g36.12.4 Power-on/Reset-Test method 51g3ETSI ETSI EN 302 340 V2.1.1 (2016-05) 6 6.12.5

31、Control Channel and Response Channel -Test method . 52g36.12.6 Network Control commands-Test method 53g36.12.7 Initial burst transmission-Test method 54g36.13 Receive antenna off-axis gain pattern 54g36.13.1 Test Method 54g36.13.1.1 Test site . 54g36.13.1.2 Method of measurement 54g36.14 Blocking pe

32、rformance 55g36.14.1 Test method 55g36.15 Adjacent Signal Selectivity 56g36.15.1 Test method 56g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 57g3Annex B (normative): Mechanical stability methodology 59g3Annex C (informative)

33、: Bibliography . 61g3History 62g3ETSI ETSI EN 302 340 V2.1.1 (2016-05) 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and

34、 non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/).

35、 Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the presen

36、t document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.5 to provide one voluntary means of conformi

37、ng to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC 9. Once the present document is cited in the Official Journal of the European Union under

38、 that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. National tra

39、nsposition dates Date of adoption of this EN: 16 May 2016 Date of latest announcement of this EN (doa): 31 August 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 28 February 2017 Date of withdrawal of any conflicting National Standard (dow): 28 February 20

40、18 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not

41、“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio equipment within the scope of the Directive 2014/53/EU 9. The modular structu

42、re is shown in ETSI EG 201 399 i.1. Figure 1: Void ETSI ETSI EN 302 340 V2.1.1 (2016-05) 8 Remarks on the present document The determination of the parameters of the user earth stations using a given geo-stationary satellite for the protection of the spectrum allocated to that satellite, is consider

43、ed to be under the responsibility of the satellite operator or the satellite network operators. The requirements have been selected to ensure an adequate level of compatibility with other radio services. The levels, however, do not cover extreme cases which may occur in any location but with a low p

44、robability of occurrence. The present document is based on the application of ITU-R Resolution 902 (WRC-03) i.2. The present document may not cover those cases where a potential source of interference which is producing individually repeated transient phenomena or a continuous phenomenon is present,

45、 e.g. a radar or broadcast site in the near vicinity. In such a case it may be necessary to use special protection applied to either the source of interference, or the interfered part or both. The present document does not contain any requirement, recommendation or information about the installation

46、 of the ESV. All parts of the below-deck unit related to reception, processing and presentation of the received information except the control channel are not within the scope of the present document. The syntax of the control channel messages is outside the scope of the present document. The presen

47、t document is based upon the standard for environmental conditions for marine navigational equipment, CENELEC EN 60945 7. In addition, attention should be paid to clause 11.1 (Acoustic noise and signals), and clause 11.2 (Compass safe distance). ETSI ETSI EN 302 340 V2.1.1 (2016-05) 9 1 Scope The pr

48、esent document applies to Earth Stations located on board Vessels (ESVs) which have the following characteristics: The ESV is comprised of all the equipment, electrical and mechanical, from the antenna itself to the interface with other communications equipment on board (usually referred to as the t

49、errestrial interface). The ESV transmits in the frequency range from 14,00 GHz to 14,50 GHz allocated to the Fixed Satellite Services (FSS) (earth-to-space). The ESV receives in one or more frequencies within the range from 10,70 GHz to 12,75 GHz in the bands allocated to the Fixed Satellite Services (FSS) (space-to-earth), depending on the ITU Region where the ESV is located. The ESV uses linear polarization. The ESV operates through a geostationary satellite at least 2 to 3 away from any other geostationary satellite operating in the same frequency b