ETSI EN 302 574-3-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2.pdf

1、 ETSI EN 302 574-3 V2.1.1 (2016-06) Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2

2、of the Directive 2014/53/EU; Part 3: User Equipment (UE) for narrowband systems HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 2 Reference REN/SES-00397 Keywords MES, mobile, MSS, narrowband, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +3

3、3 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available

4、 in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prev

5、ailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETS

6、I documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized

7、 in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to repro

8、duction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the

9、 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative refere

10、nces . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 10g33.3 Abbreviations . 10g34 Technical requirements specifications . 11g34.1 Environmental profile . 11g34.2 Conformance requirements 11g34.2.0 General 11g34.2.1 Introduction. 11g34.

11、2.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) 12g34.2.2.1 Justification . 12g34.2.2.2 Technical requirements . 12g34.2.2.3 Conformance test 14g34.2.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) 14g34.2.3.1 Justification . 14g34.2.3

12、.2 Technical requirements . 14g34.2.3.3 Conformance test 16g34.2.4 Unwanted emissions in carrier-off state 16g34.2.4.1 Justification . 16g34.2.4.2 Technical requirements . 16g34.2.4.3 Conformance test 17g34.2.5 UE Control and Monitoring Functions (CMF) . 17g34.2.5.1 Absence of a valid network handli

13、ng of output power 17g34.2.5.1.1 Definition. 17g34.2.5.1.2 Limit 17g34.2.5.1.3 Conformance . 17g34.2.5.2 Loss of signal handling of output power . 17g34.2.5.2.1 Definition. 17g34.2.5.2.2 Limit 18g34.2.5.2.3 Conformance . 18g34.2.6 Receiver Adjacent Channel Selectivity. 18g34.2.6.1 Justification . 18

14、g34.2.6.2 Technical requirements . 18g34.2.6.3 Conformance test 18g34.2.7 Receiver Blocking Characteristics 18g34.2.7.1 Justification . 18g34.2.7.2 Technical requirements . 18g34.2.7.3 Conformance test 19g35 Testing for compliance with technical requirements 19g35.1 Environmental conditions for test

15、ing . 19g35.2 Interpretation of the measurement results 19g35.3 Essential radio test suites 20g35.3.1 General 20g35.3.1.1 Description of equipment 20g35.3.1.2 Testing of host-connected equipment and plug-in modules 21g3ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 4 5.3.1.2.1 Alternative approaches 21g35.

16、3.1.2.2 Alternative A: combined equipment 21g35.3.1.2.3 Alternative B: use of a test jig . 21g35.3.1.3 CMF/Special Test Equipment (STE) 21g35.3.1.4 General test requirements 21g35.3.1.4.1 UE test modes 21g35.3.1.4.2 Special Test Equipment (STE) 22g35.3.1.4.3 Laboratory Test Equipment (LTE) 23g35.3.1

17、.4.4 Methods of test for UE RF emissions according to the equipment type 23g35.3.1.4.5 Procedures for measurement of radiated emissions . 23g35.3.1.4.6 Procedures for measurement of conducted emissions . 28g35.3.2 Unwanted emissions outside the band 1 980 MHz to 2 010 MHz (carrier-on state) 30g35.3.

18、2.1 Method of test . 30g35.3.2.2 Peak measurement . 31g35.3.2.3 Average measurement. 31g35.3.2.4 Test requirements 31g35.3.3 Unwanted emissions within the band 1 980 MHz to 2 010 MHz (carrier-on state) 32g35.3.3.1 Method of test . 32g35.3.3.2 Measurement method 32g35.3.3.3 Test requirements 33g35.3.

19、4 Unwanted emissions in carrier-off state 33g35.3.4.1 Method of test . 33g35.3.4.2 Measurement method 33g35.3.4.3 Test requirements 33g35.3.5 UE Control and Monitoring Functions (CMF) . 34g35.3.5.1 Method of test . 34g35.3.5.2 Testing of output power in absence of a valid network . 34g35.3.5.2.1 Tes

20、t procedure . 34g35.3.5.2.2 Measurement method 34g35.3.5.3 Testing of output power in loss of signal 34g35.3.5.3.1 Test procedure . 34g35.3.5.3.2 Measurement method 35g35.3.6 Receiver Adjacent Channel Selectivity. 35g35.3.6.1 General 35g35.3.6.2 Test set-up. 35g35.3.6.3 Test procedure . 35g35.3.7 Re

21、ceiver Blocking Characteristics 36g35.3.7.1 General 36g35.3.7.2 Test set-up. 36g35.3.7.3 Test procedure . 36g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 37g3Annex B (informative): Environmental profile specification . 39g3B

22、.1 Introduction 39g3B.2 Temperature . 39g3B.3 Voltage . 39g3B.4 Test environment 40g3Annex C (informative): Bibliography . 41g3History 42g3ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to

23、ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is avai

24、lable from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR

25、000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared und

26、er the Commissions standardisation request C(2015) 5376 final i.6 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing D

27、irective 1999/5/EC 7. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity w

28、ith the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 3 of a multi-part deliverable covering the Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200

29、 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU, as identified below: Part 1: “Complementary Ground Component (CGC) for wideband systems“; Part 2: “User Equipment (UE) for wideband systems“; Part 3: “User Equipment (UE) for narrowb

30、and systems“. National transposition dates Date of adoption of this EN: 30 May 2016 Date of latest announcement of this EN (doa): 31 August 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 28 February 2017 Date of withdrawal of any conflicting National Stan

31、dard (dow): 28 February 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisi

32、ons). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 6 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telec

33、ommunications terminal equipment within the scope of the Directive 2014/53/EU 7. The modular structure is shown in ETSI EG 201 399 i.5. ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 7 1 Scope The present document applies to User Equipment (UE) radio equipment type which have the following characteristics:

34、 these UEs have both transmit and receive capabilities and operate in a Geostationary satellite network; these UEs operate with an assigned channel signal bandwidth (CBw) smaller than 1 MHz; these UEs may be handset, handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed equipment,

35、 or may be an element in a multi-mode terminal. It may consist of a number of modules with associated connections and user interface, or may be a self-contained single unit; if the UE is an element in a multi-mode terminal, unless otherwise stated in the present document, its requirements apply only

36、 to the UE element of the terminal operating in the Mobile Satellite Service (MSS) frequency bands given in table 1. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1. Table 1: Mobile Satellite Service UE frequency bands Operating band Direc

37、tion of transmission UE frequency bands I UE Transmit (earth-to-space) 1 980 MHz to 2 010 MHz UE Receive (space-to-earth) 2 170 MHz to 2 200 MHz The present document is intended to cover the provisions of Directive 2014/53/EU 7 (RE Directive) article 3.2 which states that “.radio equipment shall be

38、so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the RE Dire

39、ctive 7 may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http:/www.newapproach.org. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or

40、 non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/do

41、cbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 Void. 2 Recommendation ITU-T O.153 (10/19

42、92): “Basic parameters for the measurement of error performance at bit rates below the primary rate“. 3 CISPR 16-1-4 (2010): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for

43、radiated disturbance measurements“. ETSI ETSI EN 302 574-3 V2.1.1 (2016-06) 8 4 ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 5 IEC 60068-2-1 (2007): “Envir

44、onmental testing - Part 2-1: Tests - Test A: Cold“. 6 IEC 60068-2-2 (2007): “Environmental testing - Part 2-2: Tests - Test B: Dry heat“. 7 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making

45、 available on the market of radio equipment and repealing Directive 1999/5/EC. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-speci

46、fic references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the app

47、lication of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TR 102 215: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Recommended approach, and possible limits for measurement uncertainty for the measurement of radiated electromagne

48、tic fields above 1 GHz“. i.2 Void. i.3 Void. i.4 Void. i.5 ETSI EG 201 399: “Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the Radio otherwise a limit of (-30 + E) dBW shall apply. NOTE 5: E (dB) is the excess

49、EIRP in the occupied bandwidth of the UE compared with 15 dBW. For a UE where the EIRP is equal to or less than 15 dBW, E shall equal 0 dB. For a UE where the EIRP is above 15 dBW, E shall equal (EIRP-15). In cases where the antenna directivity of the UE is greater than 15 dBi then the factor E shall be limited to a maximum value of 15 dB. In all other cases, the factor E shall be limited to a maximum value of 10 dB. NOTE 6: Peak Hold and Average measurements shall be performed as specified in clauses 5.3.2.2 and 5.3.2.3. ETSI ET