ETSI EN 302 998-1-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) Transmitting equipment for terrestrial mobile TV to provide multimedia multicast service Part .pdf

1、 ETSI EN 302 998-1 V1.1.1 (2011-05)Harmonized European Standard Electromagnetic compatibilityand Radio spectrum Matters (ERM);Transmitting equipment for terrestrial mobile TVto provide multimedia multicast service;Part 1: Harmonized EN covering the essential requirementsof article 3.2 of the R Essen

2、tial, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has

3、been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by

4、 ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC i.1 (as amended) laying down a procedure for the provision of informa

5、tion in the field of technical standards and regulations. The title and reference to the present document are intended to included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC 1. See article 5.1 of Dire

6、ctive 1999/5/EC 1 for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC 1 are summarised in annex A. The present document is pa

7、rt 1 of a multi-part deliverable covering Transmitting equipment for terrestrial mobile TV to provide multimedia multicast service, as identified below: Part 1: “Harmonized EN covering the essential requirements of article 3.2 of the R Part 2: “Harmonized EN covering the essential requirements of ar

8、ticle 3.2 of the R ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 14: Specific conditions for analogue and digital terrestrial TV broadcasting service transmitters“. 3 CENELEC EN 55022 (2006 + A1:2007): “Information technology equipment - Radio disturbance charac

9、teristics - Limits and methods of measurement“. 4 CENELEC EN 55011 (2007 + A2:2007): “Industrial, scientific and medical (ISM) radio-frequency equipment - Electromagnetic disturbance characteristics - Limits and methods of measurement“. 5 ETSI TR 100 028-1 (V1.4.1): “Electromagnetic compatibility an

10、d Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1“. 6 ETSI TR 100 028-2 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. 7 C

11、ENELEC EN 55016-1-1 (2007 + A1:2007 + A2:2008): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus“. ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 78 CENELEC EN 55016-4-2 (2004): “Specificat

12、ion for radio disturbance and immunity measuring apparatus and methods - Part 4-2: Uncertainties, statistics and limit modelling - Uncertainty in EMC measurements“. 9 ETSI EN 302 998-2 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Transmitting equipment for terrestrial m

13、obile TV to provide multimedia multicast service; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R A guide to the production of Harmonized Standards for application under the R the value of the measurement uncertainty for the measurement of each parameter shall be in

14、cluded in the test report; the recorded value of the measurement uncertainty shall be, for each measurement, equal to or lower than the figures in table 5.1. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and shall correspond to an ex

15、pansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of respectively 95 % and 95,45 % in the case where the distributions characterising the actual measurement uncertainties are normal (Gaussian). Principles for the calculation of measurement uncertainty are contained

16、in specific ETSI deliverables TR 100 028-1 5 and TR 100 028-2 6. Table 5.1 is based on such expansion factors. Table 5.1: Maximum measurement uncertainty Parameter Condition Uncertainty Spurious emissions (Conducted emissions) f 2,2 GHz 2,2 GHz 4 GHz 2,5 dB 3,0 dB 5,0 dB Out-of-band emissions (Condu

17、cted emissions) 2,5 dB Cabinet radiation (radiated emissions) See note. 30 MHz f 1 GHz (OATS) 30 MHz f 1 GHz (FAR) 1 GHz f 4,5 GHz (FAR) 6,3 dB 5,3 dB 5,2 dB NOTE: Please refer to EN 55016-4-2 8, clause 4.1, table 1. 5.3 Essential radio test suites 5.3.1 Spurious emissions The recommended test arran

18、gement for transmitters utilising a specific technology is described in clause 4.2 of the relevant technology-dependent part of the multi-part standard EN 302 998 (i.e. EN 302 998-2 9 for transmitters utilising OFDM technology, etc.). ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 185.3.1.1 Initial conditi

19、ons Test environment: - the normal operating environment, as declared by the equipment manufacturer. Test frequencies: 1) the lowest operating frequency of the EUT; 2) the highest operating frequency of the EUT; 3) a frequency mid-way between 1) and 2) above. Test arrangement: 1) connect the EUT to

20、the test load, via the coupling device; 2) connect the spectrum analyser to the coupling device. For the purposes of this test no test signal is required, the manufacturer shall ensure that the full rated output power of the transmitter will be maintained during this test. 5.3.1.2 Test procedure 1)

21、operate the EUT at each of the test frequencies as defined in clause 5.3.1.1; 2) measure the results on the spectrum analyser. 5.3.1.3 Test requirements The results obtained shall be compared to the limits in clause 4.2.2.2 in order to demonstrate compliance. 5.3.2 Out-of-band emissions The recommen

22、ded test arrangement for transmitters utilising a specific technology is described in clause 4.3 of the relevant technology-dependent part of the multi-part standard EN 302 998 (i.e. EN 302 998-2 9 for transmitters utilising OFDM technology, etc.). 5.3.2.1 Initial conditions Test environment: - the

23、normal operating environment, as declared by the equipment manufacturer. Test frequencies: 1) the lowest operating frequency of the EUT; 2) the highest operating frequency of the EUT; 3) a frequency mid-way between 1) and 2) above. Test arrangement: 1) connect the EUT to the test load, via the coupl

24、ing device; 2) connect the spectrum analyser to the coupling device. For the purposes of this test no test signal is required, the manufacturer shall ensure that the full rated output power of the transmitter will be maintained during this test. ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 195.3.2.2 Test

25、 procedure 1) operate the EUT at each of the test frequencies as defined in clause 5.3.2.1; 2) measure the results on the spectrum analyser. 5.3.2.3 Test requirements The results obtained shall be compared to the limits in clause 4.2.3.2 in order to demonstrate compliance. 5.3.3 Cabinet radiation Th

26、e recommended test arrangement for transmitters utilising a specific technology is described in clause 4.4 of the relevant technology-dependent part of the multi-part standard EN 302 998 (i.e. EN 302 998-2 9 for transmitters utilising OFDM technology, etc.). 5.3.3.1 Initial conditions Test environme

27、nt: - the normal operating environment, as declared by the equipment manufacturer. Test frequencies: 1) the lowest operating frequency of the EUT; 2) the highest operating frequency of the EUT; 3) a frequency mid-way between 1) and 2) above. Test arrangement: For the purposes of this test no test si

28、gnal is required, the manufacturer shall ensure that the full rated output power of the transmitter will be maintained during this test. 5.3.3.2 Test procedure The test method shall be in accordance with CENELEC EN 55022 3, unless physical size is a restriction, in which case the test method shall b

29、e in accordance with CENELEC EN 55011 4: tests shall not be carried out in the exclusion band, which is defined as the allocated channel; measurements shall be made in the operational mode producing the largest emission in the frequency band being investigated consistent with normal applications; th

30、e equipment shall be configured in a manner which is representative of a normal/typical operation, where practical; an attempt shall be made to maximize the detected radiated emission, e.g. by moving the cables of the equipment; the configuration and mode of operation during measurements shall be pr

31、ecisely noted in the test report; RF input/output ports shall be correctly terminated; the tests shall be carried out at a point within the specified normal operating environmental range and at the rated supply voltage for the equipment. 5.3.3.3 Test requirements The results obtained shall be compar

32、ed to the limits in clause 4.2.4.2 in order to demonstrate compliance. ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 20Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) The HS Requirements and conformance Test specifications Table (HS-RTT) in table A.1 serves a number

33、 of purposes, as follows: it provides a statement of all the requirements in words and by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it provides a statement of all the test procedures corresponding to those r

34、equirements by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it qualifies each requirement to be either: - Unconditional: meaning that the requirement applies in all circumstances; or - Conditional: meaning that

35、 the requirement is dependent on the manufacturer having chosen to support optional functionality defined within the schedule. in the case of Conditional requirements, it associates the requirement with the particular optional service or functionality; it qualifies each test procedure to be either:

36、- Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the referenced procedures; - Other: meaning that the test procedure is illustrative but other means of demonstrating compliance with the requi

37、rement are permitted. Table A.1: HS Requirements and conformance Test specifications Table (HS-RTT) Harmonized Standard EN 302 998-1 The following requirements and test specifications are relevant to the presumption of conformity under the article 3.2 of the R those designated “O“ make up the Other

38、Test Suite; for those designated “X“ there is no test specified corresponding to the requirement. The completion of all tests classified “E“ as specified with satisfactory outcomes is a necessary condition for a presumption of conformity. Compliance with requirements associated with tests classified

39、 “O“ or “X“ is a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivalent test or by manufacturers assertion supported by appropriate entries in the technical construction file. Clause Number Identification of clause(s) defining the

40、 test specification in the present document unless another document is referenced explicitly. Where no test is specified (that is, where the previous field is “X“) this field remains blank. ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 22Annex B (informative): The EN title in the official languages The en

41、largement of the European Union (EU) resulted in a requirement from the EU for a larger number of languages for the translation of the titles of Harmonized Standards and mandated ENs that are to be listed in the Official Journal to support the implementation of this legislation. For this reason the

42、title translation concerning the present document can be consulted via the e-approval application. ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 23Annex C (informative): Bibliography Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of

43、 the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC (EMC Directive). Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use

44、within certain voltage limits (LV Directive). IEC 60489-1 + Am1 (1996) + Am2 (1999): “Methods of measurement for radio equipment used in the mobile services. Part 1: General definitions and standard conditions of measurement“. CISPR 16-2-3 Ed. 2.0 b:2006: “Specification for radio disturbance and imm

45、unity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements“. ETSI ETSI EN 302 998-1 V1.1.1 (2011-05) 24History Document history V1.1.1 July 2010 Public Enquiry PE 20101109: 2010-07-12 to 2010-11-09 V1.1.1 March 2011 Vote V 20110520: 2011-03-21 to 2011-05-20 V1.1.1 May 2011 Publication