ETSI EN 303 098-2-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Maritime low power personal locating devices employing AIS Part 2 Harmonized EN covering the e.pdf

1、 ETSI EN 303 098-2 V1.2.1 (2014-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating devices employing AIS; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R Essential, or potentially Essential, IPRs notified to ETSI

2、 in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existen

3、ce of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spe

4、ctrum Matters (ERM). The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC i.2 as amended by Directive 98/48/EC i.4. The title and reference to the present document are intended to be included in the publication in th

5、e Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC i.1. See article 5.1 of Directive 1999/5/EC i.1 for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in

6、 the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC i.1 are summarized in annex A. The present document is part 2 of a multi-part deliverable covering the Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime low power personal locating de

7、vices employing AIS as identified below: Part 1: “Technical characteristics and methods of measurement“; Part 2: “Harmonized EN covering the essential requirements of article 3.2 of the R Maritime low power personal locating devices employing AIS; Part 1: Technical characteristics and methods of mea

8、surement“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equ

9、ipment and telecommunications terminal equipment and the mutual recognition of their conformity (R A guide to the production of Harmonized Standards for application under the R Uncertainties in the measurement of mobile radio equipment characteristics“. 3 Abbreviations For the purposes of the presen

10、t document, the following abbreviations apply: AIS Automatic Identification System ERP Effective Radiated Power GNSS Global Navigation Satellite System RF Radio Frequency 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under

11、the environmental profile for operation of the equipment, which shall be declared by the supplier. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 Conf

12、ormance requirements 4.2.1 Transmitter frequency error 4.2.1.1 Definition The frequency error is defined in EN 303 098-1 1, clause 8.1.1. 4.2.1.2 Limit The transmitter frequency error limit shall be as stated in EN 303 098-1 1, clause 8.1.3. 4.2.1.3 Conformance Conformance tests as defined in clause

13、 5.3.1 shall be carried out. 4.2.2 Conducted power 4.2.2.1 Definition The conducted power is defined in EN 303 098-1 1, clause 8.2.1. 4.2.2.2 Limit The conducted power limit shall be as stated in EN 303 098-1 1, clause 8.2.3. ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 94.2.2.3 Conformance Conformance t

14、ests as defined in clause 5.3.2 shall be carried out. 4.2.3 Effective radiated power (ERP) 4.2.3.1 Definition The ERP is defined in EN 303 098-1 1, clause 8.3.1. 4.2.3.2 Limit The ERP limit shall be as stated in EN 303 098-1 1, clause 8.3.3. 4.2.3.3 Conformance Conformance tests as defined in clause

15、 5.3.3 shall be carried out. 4.2.4 Transmitter spectrum mask 4.2.4.1 Definition The transmitter spectrum mask is defined in EN 303 098-1 1, clause 8.4.1. 4.2.4.2 Limit The transmitter spectrum mask limit shall be as stated in EN 303 098-1 1, clause 8.4.3. 4.2.4.3 Conformance Conformance tests as def

16、ined in clause 5.3.4 shall be carried out. 4.2.5 Transmitter transient behaviour - output power 4.2.5.1 Definition The transmitter transient behaviour - output power is defined in EN 303 098-1 1, clause 8.5.1. 4.2.5.2 Limit The transmitter transient behaviour - output power limit shall be as stated

17、in EN 303 098-1 1, clause 8.5.3. 4.2.5.3 Conformance Conformance tests as defined in clause 5.3.5 shall be carried out. 4.2.6 Transmitter transient behaviour - frequency deviation 4.2.6.1 Definition The transmitter transient behaviour - frequency deviation is defined in EN 303 098-1 1, clause 8.6.1.

18、 4.2.6.2 Limit The transmitter transient behaviour - frequency deviation limit shall be as stated in EN 303 098-1 1, clause 8.6.3. ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 104.2.6.3 Conformance Conformance tests as defined in clause 5.3.6 shall be carried out. 4.2.7 Synchronization accuracy 4.2.7.1 D

19、efinition The synchronization accuracy is defined in EN 303 098-1 1, clause 8.7.1. 4.2.7.2 Limit The synchronization accuracy limit shall be as stated in EN 303 098-1 1, clause 8.7.3. 4.2.7.3 Conformance Conformance tests as defined in clause 5.3.7 shall be carried out. 4.2.8 Spurious emissions 4.2.

20、8.1 Definition The spurious emissions are defined in EN 303 098-1 1, clause 8.8.1. 4.2.8.2 Limit The spurious emissions limits shall be as stated in EN 303 098-1 1, clause 8.8.3. 4.2.8.3 Conformance Conformance tests as defined in clause 5.3.8 shall be carried out. 5 Testing for compliance with tech

21、nical requirements 5.1 Environmental conditions for testing Tests defined in the present document shall be carried out at representative points within the boundary limits of the declared operational environmental profile. Where technical performance varies subject to environmental conditions, tests

22、shall be carried out under a sufficient variety of environmental conditions (within the boundary limits of the declared operational environmental profile) to give confidence of compliance for the affected technical requirements. The test conditions and procedures shall be as defined in EN 303 098-1

23、1, clause 6. 5.2 Interpretation of the measurement results The interpretation of the results recorded in a test report for the measurements described in the present document shall be as follows: the measured value related to the corresponding limit will be used to decide whether an equipment meets t

24、he requirements of the present document; the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report; ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 11 the recorded value of the measurement uncertainty shall be, for each measurement, equal to or lower

25、 than the figures in table 2. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of respectively 95 % and 95,45 % in the case

26、 where the distributions characterizing the actual measurement uncertainties are normal (Gaussian). Principles for the calculation of measurement uncertainty are contained in TR 100 028 i.5, in particular in annex D of the TR 100 028-2. Table 2 is based on such expansion factors. Table 2: Absolute m

27、easurement uncertainties: maximum values Parameter Maximum uncertainty RF frequency 1 x 10-7RF power 0,75 dB Frequency deviation 5 % Radiated emission of transmitter 6 dB Transmitter transient time 20 % Transmitter transient frequency 250 Hz 5.3 Essential radio test suites 5.3.1 Transmitter frequenc

28、y error The test specified in EN 303 098-1 1, clause 8.1.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.1.2 in order to prove compliance with the requirement. 5.3.2 Conducted power The test specified in EN 303 098-1 1, clause 8.2.2 shall be carried out. Th

29、e results obtained shall be compared to the limits in clause 4.2.2.2 in order to prove compliance with the requirement. 5.3.3 Effective radiated power (ERP) The test specified in EN 303 098-1 1, clause 8.3.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.3.2

30、 in order to prove compliance with the requirement. 5.3.4 Transmitter spectrum mask The test specified in EN 303 098-1 1, clause 8.4.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.4.2 in order to prove compliance with the requirement. 5.3.5 Transmitter tra

31、nsient behaviour - output power The test specified in EN 303 098-1 1, clause 8.5.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.5.2 in order to prove compliance with the requirement. 5.3.6 Transmitter transient behaviour - frequency deviation The test spec

32、ified in EN 303 098-1 1, clause 8.6.2 shall be carried out. The results obtained shall be compared to the limits in clause 4.2.6.2 in order to prove compliance with the requirement. 5.3.7 Synchronization accuracy The test specified in EN 303 098-1 1, clause 8.7.2 shall be carried out. The results ob

33、tained shall be compared to the limits in clause 4.2.7.2 in order to prove compliance with the requirement. ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 125.3.8 Spurious emissions The test specified in EN 303 098-1 1, clause 8.8.2 shall be carried out. The results obtained shall be compared to the limits

34、 in clause 4.2.8.2 in order to prove compliance with the requirement. ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 13Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) The HS Requirements and conformance Test specifications Table (HS-RTT) in table A.1 serves a number

35、of purposes, as follows: it provides a statement of all the requirements in words and by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it provides a statement of all the test procedures corresponding to those re

36、quirements by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it qualifies each requirement to be either: - Unconditional: meaning that the requirement applies in all circumstances; or - Conditional: meaning that

37、the requirement is dependent on the manufacturer having chosen to support optional functionality defined within the schedule. in the case of Conditional requirements, it associates the requirement with the particular optional service or functionality; it qualifies each test procedure to be either: -

38、 Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the referenced procedures; - Other: meaning that the test procedure is illustrative but other means of demonstrating compliance with the requir

39、ement are permitted. Table A.1: HS Requirements and conformance Test specifications Table (HS-RTT) Harmonized Standard EN 303 098-2 The following requirements and test specifications are relevant to the presumption of conformity under the article 3.2 of the R those designated “O“ make up the Other T

40、est Suite; for those designated “X“ there is no test specified corresponding to the requirement. The completion of all tests classified “E“ as specified with satisfactory outcomes is a necessary condition for a presumption of conformity. Compliance with requirements associated with tests classified

41、“O“ or “X“ is a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivalent test or by manufacturers assertion supported by appropriate entries in the technical construction file. Clause Number Identification of clause(s) defining the

42、test specification in the present document unless another document is referenced explicitly. Where no test is specified (that is, where the previous field is “X“) this field remains blank. ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 15Annex B (informative): Change History date Version Information about

43、changes June 2013 V0.0.1 First draft HS from TG26#35 ETSI ETSI EN 303 098-2 V1.2.1 (2014-11) 16History Document history V1.1.0 July 2013 EN Approval Procedure AP 20131106: 2013-07-09 to 2013-11-06 V1.1.1 February 2014 Vote V 20140422: 2014-02-21 to 2014-04-22 V1.2.1 September 2014 Vote V 20141116: 2014-09-17 to 2014-11-17 V1.2.1 November 2014 Publication