ETSI EN 303 213-6-1-2016 Advanced Surface Movement Guidance and Control System (A-SMGCS) Part 6 Harmonised Standard covering the essential requirements of article 3 2 of the Direct_1.pdf

1、 ETSI EN 303 213-6-1 V2.1.1 (2016-05) Advanced Surface Movement Guidance and Control System (A-SMGCS); Part 6: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU for deployed surface movement radar sensors; Sub-part 1: X-band sensors using pulsed signa

2、ls and transmitting power up to 100 kW HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 213-6-1 V2.1.1 (2016-05)2 Reference REN/ERM-JTFEA-20 Keywords aeronautical, ATM, interoperability, regulation ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93

3、 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/o

4、r in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print

5、of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at h

6、ttps:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means,

7、 electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. Europea

8、n Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners

9、. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 303 213-6-1 V2.1.1 (2016-05)3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 6g3Executive Summary 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informati

10、ve references 8g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 9g33.3 Abbreviations . 9g34 Technical requirements specifications . 10g34.1 Environmental profile . 10g34.2 Conformance requirements 10g34.2.1 Transmitter requirements 10g34.2.1.1 Operating frequency 10g34.

11、2.1.1.1 Definition. 10g34.2.1.1.2 Limits 10g34.2.1.1.3 Conformance . 10g34.2.1.2 Transmitter power . 10g34.2.1.2.1 Definition. 10g34.2.1.2.2 Limits 10g34.2.1.2.3 Conformance . 10g34.2.1.3 Out-of-band emissions 11g34.2.1.3.1 Definition. 11g34.2.1.3.2 Limits 12g34.2.1.3.3 Conformance . 13g34.2.1.4 Spu

12、rious emissions 13g34.2.1.4.1 Definition. 13g34.2.1.4.2 Limits 14g34.2.1.4.3 Conformance . 14g34.2.2 Receiver requirements 14g34.2.2.1 Receiver Selectivity 14g34.2.2.1.1 Limit 14g34.2.2.1.2 Conformance . 15g35 Testing for compliance with technical requirements 15g35.0 General requirements . 15g35.1

13、Environmental conditions for testing . 15g35.1.1 Introduction. 15g35.1.2 Standard operation mode for testing . 15g35.1.3 Normal temperature and humidity 15g35.1.4 Normal test power supply . 15g35.2 Interpretation of the measurements results . 15g35.3 Radio test suites 16g35.3.1 Transmitter test spec

14、ification 16g35.3.1.1 Operating frequency 16g35.3.1.2 Transmitter power . 16g35.3.1.3 Out-of-Band-emissions . 17g35.3.1.4 Spurious emissions 18g35.3.2 Receiver test specification 19g35.3.2.1 Receiver Selectivity 19g35.3.2.1.0 General 19g35.3.2.1.1 Receiver Out-of-Band selectivity 19g3ETSI ETSI EN 30

15、3 213-6-1 V2.1.1 (2016-05)4 5.3.2.1.2 Receiver spurious response rejection. 20g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 21g3Annex B (normative): Transmission power and unwanted emissions of radar systems with indirect me

16、thods . 22g3Annex C (informative): Bibliography . 23g3History 24g3ETSI ETSI EN 303 213-6-1 V2.1.1 (2016-05)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is pub

17、licly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETS

18、I Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or

19、 may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5

20、376 final i.13 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document i

21、s cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of t

22、hat Directive, and associated EFTA regulations. The present document is part 6, sub-part 1 of a multi-part deliverable covering Advanced Surface Movement Guidance and Control System (A-SMGCS), as identified below: Part 1: “Community Specification for application under the Single European Sky Interop

23、erability Regulation EC 552/2004 for A-SMGCS Level 1 including external interfaces“; Part 2: “Community Specification for application under the Single European Sky Interoperability Regulation EC 552/2004 for A-SMGCS Level 2 including external interfaces“; Part 3: “Community Specification for applica

24、tion under the Single European Sky Interoperability Regulation EC 552/2004 for a deployed cooperative sensor including its interfaces“; Part 4: “Community Specification for application under the Single European Sky Interoperability Regulation EC 552/2004 for a deployed non-cooperative sensor includi

25、ng its interfaces “; Part 5: “Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU for multilateration equipment“; Part 6: “Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU for deployed surface movement r

26、adar sensors“; Sub-part 1: “X-band sensors using pulsed signals and transmitting power up to 100 kW“. NOTE: SMR systems using FM-CW signals may be covered by future sub-parts of this multi-part deliverable. National transposition dates Date of adoption of this EN: 20 May 2016 Date of latest announce

27、ment of this EN (doa): 31 August 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 28 February 2017 Date of withdrawal of any conflicting National Standard (dow): 28 February 2018 ETSI ETSI EN 303 213-6-1 V2.1.1 (2016-05)6 Modal verbs terminology In the pres

28、ent document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables

29、 except when used in direct citation. Executive Summary The present document covers the essential requirements for efficient use of radio spectrum by surface movement radar sensors in the bands 9 000 MHz to 9 200 MHz and 9 300 MHz to 9 500 MHz using pulsed signals and a transmitting power up to 100

30、kW. The current version includes necessary changes due to adaption to the new Radio Equipment Directive 2014/53/EU i.1. ETSI ETSI EN 303 213-6-1 V2.1.1 (2016-05)7 1 Scope The present document applies to X-band radar sensors intended for the surveillance of airport surface movement traffic with the f

31、ollowing characteristics: Operating in one or both of the following frequency ranges: - 9 000 MHz to 9 200 MHz and 9 300 MHz to 9 500 MHz utilizing modulated or unmodulated pulses. Transmitter Peak Envelope Power up to 100 kW. The transceiver-antenna connection is using a hollow metallic rectangular

32、 waveguide. The antenna is rotating, waveguide-based and passive. At the transceiver output an RF-circulator is used. NOTE 1: Since transceiver and antenna are hollow metallic rectangular waveguide based the frequency range for measurements that needs to be addressed covers 6,56 GHz to 26 GHz. The l

33、ower limit of this frequency range is obtained as cut-off frequency of the combination of WR112/R84 taper section and a WR90/R100 Waveguide IEC 60153-2 i.3. The upper limit corresponds to the upper limit stated in ERC/Recommendation 74-01 i.5. NOTE 2: Since at the transceiver output an RF circulator

34、 is used, it is assumed that the transceiver characteristics remain independent from the antenna. NOTE 3: Aeronautical Surface Movement Radars covered by the present document are expected to use the bands 9 000 MHz to 9 200 MHz and/or 9 300 MHz to 9 500 MHz. According article 5 of the ITU Radio Regu

35、lations i.6 the band 9 000 MHz to 9 200 MHz is allocated to the Aeronautical Radionavigation Service on a primary basis and the band 9 300 MHz to 9 500 MHz is allocated to the Radionavigation Service on a primary basis. The present document contains requirements to demonstrate that “. Radio equipmen

36、t shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“ i.1. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3

37、 of the Radio Equipment Directive 2014/53/EU i.1 as well as essential requirements under the SES Interoperability Regulation 552/2004 i.9 and related implementing rules and/or essential requirements under the EASA basic regulation 216/2008 i.12 may apply to equipment within the scope of the present

38、document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced docum

39、ent (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their

40、long term validity. The following referenced documents are necessary for the application of the present document. Not applicable. ETSI ETSI EN 303 213-6-1 V2.1.1 (2016-05)8 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version n

41、umber) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guaran

42、tee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisati

43、on of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Merrill I. Skolnik: “Radar Handbook“, 2nd Edition, McGraw Hill publications. i.3 IEC 60153-2 (Edition 2.0, 1974): “Hollow metallic waveguides. Part 2: Relevant

44、 specifications for ordinary rectangular waveguides“. i.4 ECC/Recommendation (02)05 (2012): “Unwanted emissions“. i.5 ERC/Recommendation 74-01 (2011): “Unwanted emissions in the spurious domain“. i.6 ITU Radio Regulations (2012). i.7 Recommendation ITU-R M.1177-4 (2011): “Techniques for measurement

45、of unwanted emissions of radar systems“. i.8 Recommendation ITU-R SM.1541-5 (2013): “Unwanted emissions in the out-of-band domain“. i.9 EC Regulation No 552/2004 of the European Parliament and of the Council of 10 March 2004 on the interoperability of the European Air Traffic Management network (int

46、eroperability Regulation), OJ L 96, 31.03.2004, p. 26 as amended by Regulation (EC) No 1070/2009, OJ L 300, 14.11.2009, p. 34. i.10 ETSI TR 100 028 (all parts) (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment charac

47、teristics“. i.11 ETSI TR 100 028-2 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. i.12 Regulation (EC) 216/2008 of the European Parliament and of the Council of 20 February 2008 on common

48、 rules in the field of civil aviation and establishing a European Aviation Safety Agency, and repealing Council Directive 91/670/EEC, Regulation (EC) No 1592/2002 and Directive 2004/36/EC. i.13 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the Europe

49、an Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: necessary bandwidth: width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under s