ETSI EN 303 354-2017 Amplifiers and active antennas for TV broadcast reception in domestic premises Harmonised Standard covering the essential requirements of article 3 2 of Direct_1.pdf

1、 ETSI EN 303 354 V1.1.1 (2017-03) Amplifiers and active antennas for TV broadcast reception in domestic premises; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 354 V1.1.1 (2017-03) 2 Reference DEN/ERM-TG17

2、-16 Keywords amplification, antenna, broadcasting, harmonised standard ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7

3、803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the pr

4、ior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present

5、 document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to

6、one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The cont

7、ent of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade M

8、arks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 303 354 V1.1.1 (2017-03) 3

9、Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references 6g32.2 Informative references . 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions . 7g33.2 Symbols . 7g33.3 Abbreviations 7g34 Technica

10、l requirements specifications . 8g34.1 Environmental profile 8g34.2 General conditions of measurement 8g34.2.1 General . 8g34.2.2 Equipment configuration . 8g34.2.3 Test conditions . 8g34.2.3.1 General . 8g34.2.3.2 Normal test conditions . 9g34.2.3.2.1 Normal temperature and humidity 9g34.2.3.2.2 Ex

11、treme temperatures . 9g34.3 General assessment 9g34.4 Equipment categorization 9g34.4a RF Connectors . 10g34.5 Conformance requirements . 10g34.5.1 Gain . 10g34.5.1.1 Definition . 10g34.5.1.2 Limits . 10g34.5.1.3 Conformance 11g34.5.2 Noise figure . 11g34.5.2.1 Definition . 11g34.5.2.2 Limits . 11g3

12、4.5.2.3 Conformance 12g34.5.3 Amplifier intermodulation . 12g34.5.3.1 Definition . 12g34.5.3.2 Limits . 12g34.5.3.3 Conformance 12g34.5.4 Return loss . 12g34.5.4.1 Definition . 12g34.5.4.2 Limits . 13g34.5.4.3 Conformance 13g34.5.5 Selectivity 13g34.5.5.1 Definition . 13g34.5.5.2 Classification 1. 1

13、3g34.5.5.3 Classification 2. 14g34.5.5.4 Classification 3. 15g34.5.5.5 Classification 4. 15g34.5.5.6 Conformance 16g34.5.6 Active antenna gain . 16g34.5.6.1 Definition . 16g34.5.6.2 Limits . 16g34.5.6.3 Conformance 17g34.5.7 Active antenna figure of merit . 17g3ETSI ETSI EN 303 354 V1.1.1 (2017-03)

14、4 4.5.7.1 Definition . 17g34.5.7.2 Limits . 17g34.5.7.3 Conformance 17g34.5.8 Active antenna intermodulation . 17g34.5.8.1 Definition . 17g34.5.8.2 Limits . 17g34.5.8.3 Conformance 18g34.5.9 Internal immunity 18g34.5.9.1 Definition . 18g34.5.9.2 Limits . 18g34.5.9.3 Conformance 18g35 Testing for com

15、pliance with technical requirements 18g35.1 Environmental conditions for testing 18g35.2 Interpretation of the measurement results . 18g35.3 Methods of measurement 19g35.3.1 Amplifier gain 19g35.3.2 Noise figure . 19g35.3.3 Amplifier intermodulation . 21g35.3.4 Return loss . 22g35.3.5 Selectivity 22

16、g35.3.6 Active antenna gain . 23g35.3.7 Active antenna figure of merit . 23g35.3.8 Active antenna intermodulation . 24g35.3.9 Internal immunity 24g35.3.9.1 Method of measurement . 24g3Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53

17、/EU . 25g3Annex B (informative): Active Antenna Theory . 26g3Annex C (informative): Change History 28g3History 29g3ETSI ETSI EN 303 354 V1.1.1 (2017-03) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pert

18、aining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secret

19、ariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on

20、 the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the

21、 Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directi

22、ve 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with

23、the corresponding essential requirements of that Directive and associated EFTA regulations. Other Union legislation may be applicable to the product(s) falling within the scope of the present document. National transposition dates Date of adoption of this EN: 20 January 2017 Date of latest announcem

24、ent of this EN (doa): 30 April 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 October 2017 Date of withdrawal of any conflicting National Standard (dow): 31 October 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “s

25、hould not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduct

26、ion The present document is a Harmonised Standard for amplifiers and active antennas used for broadcast TV reception from 470 MHz to 790 MHz and VHF (174 MHz to 230 MHz). The primary purpose of the present document is to specify technical parameters to limit the interfering effects caused by unwante

27、d signals on TV reception. ETSI ETSI EN 303 354 V1.1.1 (2017-03) 6 1 Scope The present document covers amplifiers and indoor active antennas for broadcast TV and sound reception at UHF (470 MHz to 790 MHz) and at VHF (174 MHz to 230 MHz). The present document covers the essential requirements of art

28、icle 3.2 of Directive 2014/53/EU i.1 under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be pu

29、blicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long-term validity. The following referenced documents are necessary for the application

30、of the present document. 1 CENELEC EN 50083-2:2012: “Cable networks for television signals, sound signals and interactive services - Part 2: Electromagnetic compatibility for equipment“. 2.2 Informative references References are either specific (identified by date of publication and/or edition numbe

31、r or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI

32、 cannot guarantee their long-term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on t

33、he harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Rohde Uncertainties in the measurement of mobile radio equipment characteristics“. ETSI ETSI EN 303 354 V1.1.1 (2017-03) 7 i.7 IEC 61169-24:2009:

34、 “Radio-frequency connectors - Part 24: Sectional specification - Radio frequency coaxial connectors with screw coupling, typically for use in 75 cable networks (type F)“. i.8 IEC 61169-2:2007: “Radio-frequency connectors - Part 2: Sectional specification - Radio frequency coaxial connectors of type

35、 9,52“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: amplifier: indoor or outdoor equipment intended to amplify terrestrial broadcast signals active antenna: antenna equipped with an integrated low noise

36、 amplifier for indoor use (equipment type A) category: method of classifying equipment according to its type P,D,L and selectivity class 0,1,2,3,4 Digital Terrestrial Television (DTT): platform for the delivery of digital TV content via terrestrial broadcasting domestic amplifier: general purpose am

37、plifier for use in domestic premises intended to amplify terrestrial broadcast signals (equipment type D) internal immunity: ability of a device, equipment or system to perform without degradation in the presence of electromagnetic disturbances appearing at its normal input terminals or antennas lau

38、nch amplifier: high output level amplifier used to distribute terrestrial broadcast signals to multiple receivers (equipment type L) preamplifier: low noise amplifier with one or more outputs typically used immediately after a terrestrial receive antenna NOTE: A masthead amplifier is a preamplifier

39、for outdoor use with terrestrial broadcast signals (equipment type P). UHF (Ultra High Frequency) band: broadcast band from 470 MHz to 790 MHz divided into 40 channels, each 8 MHz wide, numbered from 21 to 60 VHF (Very High Frequency) band: broadcast band from 174 MHz to 230 MHz divided into 8 chann

40、els, each 7 MHz wide, numbered from 5 to 12 3.2 Symbols For the purposes of the present document, the following symbols apply: nf Noise Figure, expressed in dB F Noise Factor IM3 3rd order intercept 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: AAUT A

41、ctive Antenna Under Test AC Alternating Current AUT Amplifier Under Test CW Carrier Wave DC Direct CurrentENR Excess Noise Ratio ETSI ETSI EN 303 354 V1.1.1 (2017-03) 8 E-UTRA Evolved Universal Terrestrial Radio Access GTEM Gigahertz Transverse ElectroMagnetic IMD Intermodulation Distortion IMT Inte

42、rnational Mobile Telecommunication MATV Master Antenna Television RF Radio Frequency RL Return Loss SNR Signal to Noise Ratio SWR Standing Wave RatioTOI Third Order Intercept TV TeleVision UHF Ultra High Frequency VHF Very High Frequency 4 Technical requirements specifications 4.1 Environmental prof

43、ile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document which are identified as applicable in annex

44、 A at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 General conditions of measurement 4.2.1 General This clause gives the general operational conditions. The product-specific operating conditions will be derived from the product descriptio

45、n and documentation and stated in the test report. The levels of the test signals shall be expressed either in terms of the power relative to 1 mW (dBm) for amplifiers or the field strength relative to 1 V/m (dBV/m) for antennas. 4.2.2 Equipment configuration Power and signal distribution, grounding

46、, interconnecting cabling and physical placement of equipment of a test system shall simulate the typical application and usage in so far as is practicable, and shall be in accordance with the relevant product specifications. Only configurations within the range of setting likely to occur in normal

47、use need be considered. 4.2.3 Test conditions 4.2.3.1 General The equipment shall be tested under normal test conditions according to the relevant product and basic standards or to the information accompanying the equipment, which shall be within the manufacturers declared range of humidity, tempera

48、ture and supply voltage. The test conditions shall be recorded in the test report. The test configuration and mode of operation shall be representative of the intended use and shall be recorded in the test report. Typical test equipment will usually have a characteristic impedance of 50 and antennas

49、 or amplifiers typically have a characteristic impedance of 75 . In such cases, impedance matching attenuators or transformers should be used to interface to the equipment under test. ETSI ETSI EN 303 354 V1.1.1 (2017-03) 9 The equipment under test should be fed by the intended power supply supplied by the manufacturer or a suitable equivalent. For amplifiers with multiple inputs or multiple outputs, any ports that would otherwise be unconnected shall be terminated in a well-matched load. For devices with multiple outputs, all outputs should be tes