ETSI EN 303 372-2-2016 Satellite Earth Stations and Systems (SES) Satellite broadcast reception equipment Harmonised Standard covering the essential requirements of article 3 2 of _1.pdf

1、 ETSI EN 303 372-2 V1.1.1 (2016-04) Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 2: Indoor unit HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 372-2 V1.1.1

2、(2016-04) 2 Reference DEN/SES-00376-2 Keywords broadcasting, receiver, requirements, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfe

3、cture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be

4、 modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretari

5、at. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, plea

6、se send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written perm

7、ission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand t

8、he ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 303

9、 372-2 V1.1.1 (2016-04) 3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Symbols and abbreviations . 6g33.1 Symbols 6g33.2 Abbreviations . 6g34 Technical requir

10、ements specifications . 6g34.1 Environmental profile . 6g34.2 Equipment capabilities . 6g34.3 Conformance requirements 6g34.3.1 Adjacent signal selectivity 6g34.3.2 Dynamic range 7g35 Testing for compliance with technical requirements 7g35.1 Environmental conditions for testing . 7g35.2 Interpretati

11、on of the measurement results 8g36 Test methods 8g36.1 Adjacent signal selectivity 8g36.2 Dynamic range . 8g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 9g3Annex B (informative): Interface between ODU and IDU . 10g3Annex C (

12、informative): Applicability in conjunction with CENELEC EN 50585:2014 11g3Annex D (informative): Applicability of parameters given in ETSI EG 203 336 . 12g3Annex E (informative): Other IDU features and performance characteristics 13g3History 14g3ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 4 Intellectual

13、 Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPR

14、s); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been

15、carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI

16、 Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.5 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the

17、laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document give

18、n in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable. Full details of the entire series

19、can be found in ETSI EN 303 372-1 i.1. National transposition dates Date of adoption of this EN: 13 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 January 2017 Date of withdrawal of any c

20、onflicting National Standard (dow): 31 January 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for th

21、e expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction See ETSI EN 303 372-1 i.1. ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 5 1 Scope The present document applies to indoor units (IDUs) for satellite broadcast reception

22、. An indoor unit gets on an input interface the signal that has been received from satellite and processed by the outdoor unit (ODU). It performs carrier selection, demodulation, audio and video decoding. Part of the IDU functionality may be integrated with the ODU. In that case the present document

23、 applies to this part of functionality as well as the remaining part in the IDU. The indoor unit may be integrated with a domestic television receiver. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectru

24、m in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest

25、 version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publicati

26、on, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or n

27、on-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their l

28、ong term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI EN 303 372-1: “Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonis

29、ed Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part-1: Outdoor unit receiving in the 10,7 GHz to 12,75 GHz frequency band“. i.2 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Mem

30、ber States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.3 ETSI EG 203 336 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards co

31、vering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.4 CENELEC EN 50585:2014: “Communications protocol to transport satellite delivered signals over IP networks“. i.5 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee f

32、or Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 6 3 Symbols and abbreviations 3.1 Symbols For the purpos

33、es of the present document, the following symbols apply: F ideal signal occupied bandwidth Rssymbol rate roll-off3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: EIRP Equivalent Isotropically Radiated Power IDU InDoor Unit ODU OutDoor Unit4 Technical req

34、uirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the supplier. The equipment shall comply with all the technical requirements of the present document

35、at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 Equipment capabilities The technical requirements of the present document apply under the capabilities of the equipment, which shall be declared by the supplier. The equipment shall comply w

36、ith all the technical requirements of the present document at all times when operating within the boundary limits of the declared equipment capabilities. Equipment capabilities comprise the following characteristics: Input frequency band Input level range Modulation and coding format 4.3 Conformance

37、 requirements 4.3.1 Adjacent signal selectivity Purpose: To enable reception of a wanted signal in presence of other signals on adjacent frequencies that are transmitted with high EIRP from near-by adjacent orbital positions. NOTE 1: Signals transmitted from the same orbital position are under contr

38、ol of the satellite operator. Signals transmitted adjacent orbital position that is not near-by are suppressed by the antenna gain pattern. Specification: Adjacent signal selectivity is specified through an increase of the required signal to noise ratio caused by the adjacent signal. ETSI ETSI EN 30

39、3 372-2 V1.1.1 (2016-04) 7 The adjacent signal shall apply the same modulation as the wanted signal. Frequency offset and power level offset of the adjacent signal with regard to the wanted signal shall take the values given in table 1. F is the ideal signal occupied bandwidth. Table 1: Adjacent sig

40、nal frequency and level Frequency offset from wanted signal Power level offset from wanted signal -F - 4 MHz 10 dB -F - 2 MHz 4 dB -F 0 dB F 0 dB F + 2 MHz 4 dB F + 4 MHz 10 dB The required signal to noise ratio in presence of an adjacent signal shall be less than 0,4 dB higher than in absence of ad

41、jacent signals. NOTE 2: In case of amplitude or phase shift keying signals the occupied bandwidth of an ideal signal is F = Rs (1 + ), where Rsis the symbol rate and is the roll-off. NOTE 3: The case with frequency offset F represents carriers sharing a transponder, F + 2 MHz represents carriers on

42、adjacent transponders of a satellite, F + 4 MHz represents carriers on different satellites. Frequency offset is meant between centre frequencies of carriers. Verification: The test method specified in clause 6.1 shall apply. 4.3.2 Dynamic range Purpose: To allow a wide range of satellite EIRP and o

43、f ODU antenna diameter. NOTE 1: Besides satellite EIRP and ODU antenna diameter, the dynamic range covers the range of coaxial cable length and LNB gain. Specification: The IDU shall be able to process without degradation input signals at any level in a range of at least 40 dB. Verification: The tes

44、t method specified in clause 6.2 shall apply. NOTE 2: The absolute input level range appears in clause 4.2. 5 Testing for compliance with technical requirements 5.1 Environmental conditions for testing Tests defined in the present document shall be carried out at representative points within the bou

45、ndary limits of the declared operational environmental profile. Where technical performance varies subject to environmental conditions, tests shall be carried out under a sufficient variety of environmental conditions (within the boundary limits of the declared operational environmental profile) to

46、give confidence of compliance for the affected technical requirements. ETSI ETSI EN 303 372-2 V1.1.1 (2016-04) 8 5.2 Interpretation of the measurement results The interpretation of the results recorded in a test report for the measurements described in the present document shall be as follows: the m

47、easured value related to the corresponding limit will be used to decide whether an equipment meets the requirements of the present document; the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report. 6 Test methods 6.1 Adjacent signal selecti

48、vity a) Two test signal generators shall be used. Each signal generator shall generate a modulated signal in the IDU input frequency range and thermal noise. b) The signal generators shall be connected to the IDU input through a splitter (combiner). c) The symbol rate shall be set to the low end of

49、the IDUs range. d) The test signal generators shall be set to the frequencies and levels according to table 1. For each row of the table: a) The IDU shall be set to receiving the signal of the first test signal generator. b) The second test signal generator shall be set to output signal off. c) The noise level (or signal to noise ratio) of the first test signal generator shall be varied in order to determine the threshold for quasi error free reception. d) The second signal generator shall be set to output signal on. e) The noise level (or