ETSI EN 303 417-2017 Wireless power transmission systems using technologies other than radio frequency beam in the 19 - 21 kHz 59 - 61 kHz 79 - 90 kHz 100 - 300 kHz 6 765 - 6 795 k_1.pdf

1、 ETSI EN 303 417 V1.1.1 (2017-09) Wireless power transmission systems, using technologies other than radio frequency beam in the 19 - 21 kHz, 59 - 61 kHz, 79 - 90 kHz, 100 - 300 kHz, 6 765 - 6 795 kHz ranges; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53

2、/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 417 V1.1.1 (2017-09) 2 Reference DEN/ERM-TG28-527 Keywords harmonised standard, radio, testing, WPT ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742

3、 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and

4、/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version

5、 kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatu

6、s.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocop

7、ying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM,

8、 UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are tradem

9、arks registered and owned by the GSM Association. ETSI ETSI EN 303 417 V1.1.1 (2017-09) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions, symbols an

10、d abbreviations . 9g33.1 Definitions 9g33.2 Symbols 10g33.3 Abbreviations . 10g34 Technical requirements specifications . 10g34.1 Environmental conditions . 10g34.2 General . 11g34.2.1 Background information . 11g34.2.2 Wanted performance criteria. 11g34.2.3 WPT operational modes 11g34.2.4 Presentat

11、ion of equipment for testing purposes 14g34.2.4.1 General 14g34.2.4.2 Choice of model for testing . 14g34.2.4.3 Testing of WPT systems . 14g34.2.4.4 On-site testing . 14g34.2.5 Mechanical and electrical design 14g34.2.5.1 General 14g34.2.5.2 Controls. 14g34.2.5.3 Shut-off facility . 15g34.3 Transmit

12、ter conformance requirements 15g34.3.1 General 15g34.3.2 Permitted range of operating frequencies . 15g34.3.2.1 Applicability 15g34.3.2.2 Description 15g34.3.2.3 Limits 15g34.3.2.4 Conformance . 15g34.3.3 Operating frequency range(s) (OFR) 15g34.3.3.1 Applicability 15g34.3.3.2 Description 15g34.3.3.

13、3 Limits 16g34.3.3.4 Conformance . 16g34.3.4 H-field requirements . 17g34.3.4.1 Applicability 17g34.3.4.2 Description 17g34.3.4.3 Limits 17g34.3.4.4 Conformance . 17g34.3.5 Transmitter spurious emissions . 17g34.3.5.1 Applicability 17g34.3.5.2 Description 17g34.3.5.3 Limits 18g34.3.5.4 Conformance .

14、 19g34.3.6 Transmitter out of band (OOB) emissions 19g34.3.6.1 Applicability 19g34.3.6.2 Description 19g34.3.6.3 Limits 19g34.3.6.4 Conformance . 19g3ETSI ETSI EN 303 417 V1.1.1 (2017-09) 4 4.3.7 WPT system unwanted conducted emissions . 20g34.3.7.1 Applicability 20g34.3.7.2 Description 20g34.3.7.3

15、Limits 20g34.3.7.4 Conformance . 20g34.4 Receiver Conformance requirements . 20g34.4.1 General 20g34.4.2 Receiver blocking . 20g34.4.2.1 Applicability 20g34.4.2.2 Description 20g34.4.2.3 Limits 20g34.4.2.4 Conformance . 21g35 Testing for compliance with technical requirements 21g35.1 Environmental c

16、onditions for testing . 21g35.2 General conditions for testing 21g35.2.1 Product information 21g35.3 Normal and extreme test conditions . 21g35.4 Test power source . 21g35.5 Normal test conditions 21g35.6 Extreme test conditions 22g35.7 Auxiliary test equipment 22g35.8 Normal test signals and test m

17、odulation . 22g35.9 Test sites and general arrangements for radiated measurements 22g35.10 Measuring receiver . 22g35.11 Measurement uncertainty . 22g36 Conformance methods of measurement for transmitters and receivers . 22g36.1 Measurement setup and alignment conditions 22g36.1.1 General 22g36.1.2

18、Mode 1: idle mode 23g36.1.3 Mode 2: charging adjustment 23g36.1.4 Mode 3 and Mode 4: power transmission arrangement 24g36.1.5 Receiver test 25g36.2 Conformance methods of measurement for transmitting parts within the WPT system 25g36.2.1 General 25g36.2.2 Measurement receiver . 26g36.2.3 WPT system

19、unwanted radiated emissions 30 MHz 26g36.2.4 WPT system unwanted conducted emissions . 27g36.3 Conformance methods of measurement for the receiving parts with a WPT System 28g36.3.1 Receiver spurious emissions . 28g36.3.2 Test Receiver blocking . 28g3Annex A (informative): Relationship between the p

20、resent document and the essential requirements of Directive 2014/53/EU . 30g3Annex B (normative): Measurement setup for EV WPT systems . 31g3Annex C (informative): Bibliography . 33g3History 34g3ETSI ETSI EN 303 417 V1.1.1 (2017-09) 5 Intellectual Property Rights Essential patents IPRs essential or

21、potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essen

22、tial, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee c

23、an be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registere

24、d by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products,

25、services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation reque

26、st C(2015) 5376 final i.6 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.3. Once the present

27、 document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requir

28、ements of that Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 14 August 2017 Date of latest announcement of this EN (doa): 30 November 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 May 2018 Date o

29、f withdrawal of any conflicting National Standard (dow): 31 May 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Ve

30、rbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 303 417 V1.1.1 (2017-09) 6 Introduction The present document has been prepared to conform to the requirements of the new Radio Equipment Directiv

31、e 2014/53/EU i.3. The present document covers wireless power transmission (WPT) systems using technologies other than radio frequency beam in the frequency ranges 19 - 21 kHz, 59 - 61 kHz, 79 - 90 kHz, 100 - 300 kHz, 6 765 - 6 795 kHz. In the context of the present document “power transmission via r

32、adio frequency beam“ means power transmission by radio waves. For the clarification of open questions for high power wireless power transmission systems to charge vehicles a SRdoc ETSI TR 103 409 i.4 was prepared. New specific requirements for such systems (e.g. higher H-field emission limits in the

33、 79 - 90 kHz band) will be reflected within a future revision of the present document. The present document is structured as follows: Clauses 1 through 3 provide a general description on the types of equipment covered by the present document and the definitions, symbols and abbreviations used. Claus

34、e 4 provides the technical requirements specifications, limits and conformance relative to transmitter and receiver. Clause 5 specifies the conditions for testing of the equipment and interpretation of the measurement results with the maximum measurement uncertainty values. Clause 6 specifies the re

35、quired measurement methods. Annex A (informative) provides the relationship between the present document and the essential requirements of Directive 2014/53/EU i.3. Annex B (normative) provides the measurement setup specifically for Electric Vehicles. ETSI ETSI EN 303 417 V1.1.1 (2017-09) 7 1 Scope

36、The present document specifies technical characteristics and methods of measurements for wireless power transmission (WPT) systems, using technologies other than radio frequency beam, in the 19 - 21 kHz, 59 - 61 kHz, 79 - 90 kHz, 100 - 300 kHz, 6 765 - 6 795 kHz ranges. The present document covers w

37、ireless power transmission systems which are regarded as radio equipment since including inherent radio communication functionality or radiodetermination via the WPT interface or port at the specific WPT frequency ranges. Such systems usually consist of: 1) A power transmitter, with additional commu

38、nication capability to control the charge function, in conjunction with the receiving part. The power transmitter could also be named as base station. 2) A power receiver, which supplies the received energy to a mobile device and performs a control/supervision function for the mobile device status a

39、nd charge operation. Both parts in combination are able to transmit and receive data in addition to the power transmission mode e.g. to control the mobile device status and to optimize the power transmission mode. These radio equipment types are capable of operating in the permitted frequency bands

40、below 30 MHz as specified in Table 1. The present document covers fixed systems, mobile and portable systems. Table 1: WPT systems within the permitted frequency bands below 30 MHz WPT frequency range Frequency Bands Applications Transmit and Receive 1 19 kHz to 21 kHz WPT systems Transmit and Recei

41、ve 2 59 kHz to 61 kHz WPT systems Transmit and Receive 3 79 kHz to 90 kHz WPT systems Transmit and Receive 4 100 kHz to 119 kHz WPT systems Transmit and Receive 119 kHz to 140 kHz WPT systems Transmit and Receive 140 kHz to 148,5 kHz WPT systems Transmit and Receive 148,5 kHz to 300 kHz WPT systems

42、Transmit and Receive 5 6 765 kHz to 6 795 kHz WPT systems NOTE 1: The frequency ranges listed in Table 1 are also used for generic inductive short range devices, according to ETSI EN 300 330 1. NOTE 2: The limits and the frequency ranges of the present document are EU wide harmonised according to EC

43、 Decision 2013/752/EU i.2 and CEPT/ERC/REC 70-03 i.1. NOTE 3: In addition, it should be noted that other frequency bands may be available in a country within the frequency range below 30 MHz. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.3 under the

44、conditions identified in Annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might

45、 be found at https:/docbox.etsi.org/Reference/. ETSI ETSI EN 303 417 V1.1.1 (2017-09) 8 NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of th

46、e present document. 1 ETSI EN 300 330 (V2.1.1) (02-2017): “Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/

47、EU“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including a

48、ny amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a

49、 particular subject area. i.1 CEPT/ERC/REC 70-03: “Relating to the use of Short Range Devices (SRD)“. i.2 EC Decision 2013/752/EU: “Commission implementing Decision of 11 December 2013 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2005/928/EC“. i.3 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1