ETSI EN 303 447-2017 Short Range Devices (SRD) Inductive loop systems for robotic mowers in the frequency range 0 Hz to 148 5 kHz Harmonised Standard covering the essential require.pdf

1、 ETSI EN 303 447 V1.1.1 (2017-09) Short Range Devices (SRD); Inductive loop systems for robotic mowers in the frequency range 0 Hz to 148,5 kHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 447 V1.1.1 (20

2、17-09) 2 Reference DEN/ERM-TG28-541 Keywords harmonised standard, inductive, measurement, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prf

3、ecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not b

4、e modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretar

5、iat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, ple

6、ase send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written per

7、mission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI regist

8、ered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Association. ETSI

9、 ETSI EN 303 447 V1.1.1 (2017-09) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 9g

10、33.3 Abbreviations . 10g34 Technical requirements specifications . 10g34.1 Environmental conditions . 10g34.2 General . 10g34.2.1 Wanted performance criteria. 10g34.2.2 RMI functional mode 10g34.2.2.1 General 10g34.2.2.2 Operational Mode . 11g34.2.2.3 Safe Mode . 11g34.2.3 Presentation of equipment

11、for testing purposes 11g34.3 Transmitter conformance requirements 11g34.3.1 Operating Frequency Range (OFR) 11g34.3.1.1 Applicability 11g34.3.1.2 Description 11g34.3.1.3 Limits 12g34.3.1.4 Conformance . 12g34.3.2 Transmitter H-field requirements . 12g34.3.2.1 Applicability 12g34.3.2.2 Description 12

12、g34.3.2.3 Limits 13g34.3.2.4 Conformance . 13g34.3.3 Transmitter spurious emissions . 13g34.3.3.1 Applicability 13g34.3.3.2 Description 13g34.3.3.3 Limits 14g34.3.3.4 Conformance . 15g34.3.4 Transmitter out of band (OOB) emissions 15g34.3.4.1 Applicability 15g34.3.4.2 Description 15g34.3.4.3 Limits

13、15g34.3.4.4 Conformance . 15g34.4 Receiver Conformance requirements . 15g34.4.1 Introduction. 15g34.4.2 Receiver unwanted emissions . 16g34.4.3 Receiver blocking . 16g34.4.3.1 Applicability 16g34.4.3.2 Description 16g34.4.3.3 Limits 16g34.4.3.4 Conformance . 16g35 Testing for compliance with technic

14、al requirements 17g35.1 Environmental conditions for testing . 17g35.2 General conditions for testing 17g3ETSI ETSI EN 303 447 V1.1.1 (2017-09) 4 5.2.1 Product information 17g35.3 Normal and extreme test conditions . 17g35.4 Artificial antenna 17g35.5 Test sites and general arrangements for radiated

15、 measurements 17g35.6 Measuring receiver . 18g35.7 Measurement uncertainty . 18g35.8 Interpretation of the measurement results 18g36 Conformance methods of measurement for transmitters and receivers . 18g36.1 General . 18g36.2 Transmitter conformance methods . 19g36.2.1 OFR 19g36.2.2 H-field . 19g36

16、.2.3 Transmitter unwanted emissions (spurious and OOB emissions) . 20g36.3 Receiver conformance methods . 20g36.3.1 Receiver spurious emissions . 20g36.3.2 Receiver blocking . 20g3Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU

17、. 24g3Annex B (normative): Test sites and procedures 25g3B.1 Set-up 1: Magnetic field measurements at a Test Garden 25g3B.2 Set-up 2: Carrier current measurements using an artificial antenna . 25g3B.2.1 General . 25g3B.2.2 Differential mode measurement . 26g3B.2.3 Common mode measurement . 26g3B.3 R

18、adiated measurements using anechoic chamber or open area test site . 26g3Annex C (normative): Artificial antenna for conducted measurements below 30 MHz . 27g3Annex D (informative): Change history . 30g3History 31g3ETSI ETSI EN 303 447 V1.1.1 (2017-09) 5 Intellectual Property Rights Essential patent

19、s IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential,

20、or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by

21、ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asser

22、ted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement b

23、y ETSI of products, services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions s

24、tandardisation request C(2015) 5376 final i.6 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i

25、.3. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the correspond

26、ing essential requirements of that Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 14 August 2017 Date of latest announcement of this EN (doa): 30 November 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e)

27、: 31 May 2018 Date of withdrawal of any conflicting National Standard (dow): 31 May 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETS

28、I Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 303 447 V1.1.1 (2017-09) 6 Introduction The present document covers Robotic Mowers with Inductive loop systems (RMI) using th

29、e frequency range below 148,5 kHz. An RMI system includes: RMI docking station: charging stations for the robotic mower and the signal generator/antenna connecting point for the signals on the integral antenna and boundary wire. Robotic Mower: receiving part inside the RMI. Boundary Wire: user insta

30、lled antenna. The present document is structured as follows: Clauses 1 through 3 provide a general description on the types of equipment covered by the present document and the definitions, symbols and abbreviations used. Clause 4 provides the technical requirements specifications, limits and confor

31、mance relative to transmitter and receiver. Clause 5 specifies the conditions for testing of the equipment and interpretation of the measurement results with the maximum measurement uncertainty values. Clause 6 specifies the required measurement methods. Annex A (informative) provides the relationsh

32、ip between the present document and the essential requirements of Directive 2014/53/EU i.3. Annex B (normative) provides necessary information on used test sites and procedures. ETSI ETSI EN 303 447 V1.1.1 (2017-09) 7 1 Scope The present document specifies technical characteristics and methods of me

33、asurements for Robotic Mowers with Inductive loop systems (RMI) below 148,5 kHz. These radio equipment types are capable of operating in all or part of the frequency bands given in table 1. Table 1: Permitted range of operation Permitted range of operation Transmit 0 Hz to 148,5 kHz Receive 0 Hz to

34、148,5 kHz NOTE: It should be noted that the frequency range between 9 kHz and 148,5 kHz is EU wide harmonised for inductive Short Range Devices according to EC Decision 2013/752/EU i.2. The present document does not cover other devices using the frequency range below 148,5 kHz, e.g. ETSI EN 303 348

35、i.9 (Inductive loop for hearing impaired in 0 kHz to 20 kHz), ETSI EN 303 454 i.10 (metal sensors). The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.3 under the conditions identified in annex A. 2 References 2.1 Normative references References are speci

36、fic, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this

37、clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 330 (V2.1.1) (02-2017): “Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz t

38、o 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version n

39、umber) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guaran

40、tee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 CEPT/ERC/REC 70-03: “Relating to the use of Short Range Devices (SRD)“. i.2 EC Decision 2013/752/EU: “

41、Commission implementing Decision of 11 December 2013 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2005/928/EC“. ETSI ETSI EN 303 447 V1.1.1 (2017-09) 8 i.3 Directive 2014/53/EU of the European Parliament and of the Council

42、 of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.4 CEPT/ERC/REC 74-01: “Unwanted emissions in the spurious domain“. i.5 ETSI EG 203 336: “Electromagnetic compatibility and Ra

43、dio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.6 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Co

44、mmittee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.7 EGMF Robotic Mowers Boundary Wire Standard RLM003-1.0/2014. i.8 CENELEC EN 50636-2-

45、107:2015: “Safety of household and similar appliances - Part 2-107: Particular requirements for robotic battery powered electrical lawnmowers“. i.9 ETSI EN 303 348: “Induction loop systems intended to assist the hearing impaired in the frequency range 10 Hz to 9 kHz; Harmonised Standard covering the

46、 essential requirements of article 3.2 of Directive 2014/53/EU“. i.10 ETSI EN 303 454: “Short Range Devices (SRD); Metal and object detection sensors in the frequency range 1 kHz to 148,5 kHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU“. i.11 Direc

47、tive 2006/42/EC or the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast). 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 300 330 1 and the followi

48、ng apply: 99 % OBW function: measurement function of a spectrum analyser antenna: factory defined loop(s) (e.g. integral antenna) and/or user defined loop(s) (e.g. boundary wire, guidance wire), which are used for the functional mode of the RMI NOTE: The inductive wire loops are installed dependent

49、from the shape of the garden. A current is fed into these inductive loops to generate a magnetic field intended for guidance and/or communication with the robotic mower. boundary wire: inductive wire loop which will be defined/prepared by the user NOTE: It can be implemented as a single or multiple turn coil installed by the user in accordance with instruction from the manufacturer for the purpose of generating magnetic fields to determine the working area. factory defined loop: either integral antenna or inductive wire loop that