ETSI EN 303 609-2016 Global System for Mobile communications (GSM) GSM Repeaters Harmonised Standard covering the essential requirements of article 3 2 of the Directive 2014 53 EU _1.pdf

1、 ETSI EN 303 609 V12.5.1 (2016-04) Global System for Mobile communications (GSM); GSM Repeaters; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 609 V12.5.1 (2016-04) 2 Reference REN/MSG-0021-RED Keyword

2、s cellular, ER-GSM, GSM, repeater, R-GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The pr

3、esent document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of E

4、TSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that

5、 the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services:

6、 https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall n

7、ot be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for th

8、e benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 303 609 V12.5.1 (2016-04) 3 Contents Intellectual Propert

9、y Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 8g34 Technical requirements specifications . 8g34.1 Environmental pr

10、ofile . 8g34.2 Conformance requirements 8g34.2.0 Introduction. 8g34.2.1 Conducted spurious emissions 9g34.2.1.1 Definition 9g34.2.1.2 Limit 9g34.2.1.3 Conformance . 10g34.2.2 Radiated spurious emissions . 10g34.2.2.1 Definition 10g34.2.2.2 Limit 10g34.2.2.3 Conformance . 10g34.2.3 Intermodulation at

11、tenuation 10g34.2.3.1 Definition 10g34.2.3.2 Limit 11g34.2.3.3 Conformance . 11g34.2.4 Out-of-band gain . 11g34.2.4.1 Definition 11g34.2.4.2 Limit 11g34.2.4.3 Conformance . 11g34.2.5 Frequency error . 11g34.2.5.1 Definition 11g34.2.5.2 Limit 11g34.2.5.3 Conformance . 11g35 Testing for compliance wit

12、h technical requirements 12g35.1 Environmental conditions for testing . 12g35.2 Interpretation of the measurement results 12g35.3 Essential radio test suites 13g35.3.1 Conducted spurious emissions 13g35.3.1.1 Initial conditions . 13g35.3.1.2 Procedures . 13g35.3.1.3 Test requirement . 13g35.3.2 Radi

13、ated spurious emissions . 13g35.3.2.1 Initial conditions . 13g35.3.2.2 Procedures . 13g35.3.2.3 Test requirement . 14g35.3.3 Intermodulation attenuation 14g35.3.3.1 Initial conditions . 14g35.3.3.2 Procedures . 14g35.3.3.3 Test requirement . 14g35.3.4 Out-of-band gain . 14g35.3.4.1 Initial condition

14、s . 14g35.3.4.2 Procedures . 14g3ETSI ETSI EN 303 609 V12.5.1 (2016-04) 4 5.3.4.3 Test requirement . 15g35.3.5 Frequency error . 15g35.3.5.1 Initial conditions . 15g35.3.5.2 Procedures . 15g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 20

15、14/53/EU . 16g3Annex B (informative): Environmental profile specification . 17g3Annex C (informative): Testing of gain for part band repeaters . 18g3C.1 Rationale for this test 18g3C.2 Gain outside pass band . 18g3C.2.1 Test purpose . 18g3C.2.2 Test case . 18g3C.2.3 Conformance requirement 18g3Histo

16、ry 19g3ETSI ETSI EN 303 609 V12.5.1 (2016-04) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be

17、found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR

18、 Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This

19、 Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). For non EU countries the present document may be used for regulatory (Type Approval) purposes. The present document has been prepared under the Commissions standardisation request C(2015) 5

20、376 final i.5 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is

21、 cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of th

22、at Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 6 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 January 2017 Date of withdrawal o

23、f any conflicting National Standard (dow): 31 January 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms

24、 for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is a revision of ETSI EN 300 609-4. The present document is part of a set of standards developed by ETSI that are designed to fit in a

25、 modular structure to cover radio equipment within the scope of the Directive 2014/53/EU i.1. The present document is produced following the guidance in ETSI EG 203 336 i.2 as applicable. ETSI ETSI EN 303 609 V12.5.1 (2016-04) 6 1 Scope The present document applies to the following radio equipment t

26、ypes: 1) Repeaters for GSM. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: GSM Repeater frequency bands GSM band Direction of transmission GSM Repeater relevant frequency bands P-GSM 900 Downlink 935 MHz to 960 MHz Uplink 89

27、0 MHz to 915 MHz E-GSM 900 Downlink 925 MHz to 960 MHz Uplink 880 MHz to 915 MHz R-GSM 900 Downlink 921 MHz to 960 MHz Uplink 876 MHz to 915 MHz ER-GSM 900 Downlink 918 MHz to 960 MHz Uplink 873 MHz to 915 MHz DCS 1 800 Downlink 1 805 MHz to 1 880 MHz Uplink 1 710 MHz to 1 785 MHz GSM 450 Downlink 4

28、60,4 MHz to 467,6 MHz Uplink 450,4 MHz to 457,6 MHz GSM 480 Downlink 488,8 MHz to 496 MHz Uplink 478,8 MHz to 486 MHz NOTE 1: In some circumstances, for instance when an operator (or more than one operator who co-ordinate the use of repeaters), is not allocated a complete band as defined in table 1-

29、1, it may be necessary to restrict the frequency range of operations of repeaters. In these circumstances, the test of “Gain outside pass band“ in annex C may be used to verify the performance of the repeater. NOTE 2: A repeater is designed to operate in one or several pass bands within the MS and B

30、TS relevant transmit bands. The present document covers requirements for GSM Repeaters for 3GPP Release 8, 9, 10, 11 and 12. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful

31、 interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced

32、document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee t

33、heir long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI TS 151 026 (V12.0.0) (10-2014): “Digital cellular telecommunications system (Phase 2+); Base Station System (BSS) equipment specification; Part 4: Repeaters (3GPP TS 51.026 v

34、ersion 12.0.0 Release 12)“. 2 Recommendation ITU-R SM.329-12 (09-2012): “Unwanted emissions in the spurious domain“. ETSI ETSI EN 303 609 V12.5.1 (2016-04) 7 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-s

35、pecific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long

36、term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the harmonisation of the laws

37、of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 ETSI EG 203 336 (V1.1.1) (08-2015): “ Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Ha

38、rmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.3 ETSI TR 100 028 (all parts) (V1.4.1) (12-2001): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. i.4 ETSI TS 145 005 (

39、V12.5.0) (04-2015): “Digital cellular telecommunications system (Phase 2+); Radio Transmission and reception (3GPP TS 45.005 version 12.5.0 Release 12)“. i.5 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical St

40、andardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and defi

41、nitions apply: broadband repeater: repeater which is designed for operation on any combination of ARFCNs (up to a specified maximum number) within the relevant band of the repeater channelized repeater: repeater which is designed for operation on a specified subset of ARFCNs within the operating ban

42、d of the repeater NOTE: The subset of ARFCNs may be determined during the manufacture of the repeater, or may be programmable. E-GSM: extended GSM 900 band (includes P-GSM band) ER-GSM 900: extended Railway GSM 900 band (includes R-GSM band) GSM: unless otherwise specified, references to GSM include

43、 GSM 400, GSM 900, ER-GSM 900 and DCS 1 800 GSM 400: unless otherwise specified, references to GSM 400 include GSM 450 and GSM 480 band GSM 900: unless otherwise specified, references to GSM 900 include P-GSM, E-GSM and R-GSM band GSM-R: GSM Railway communication, operated in the R-GSM or ER-GSM ban

44、d, respectively P-GSM: primary GSM 900 band ETSI ETSI EN 303 609 V12.5.1 (2016-04) 8 pass band: frequency range that the Repeater operates in with operational configuration NOTE: This frequency range can correspond to one or several consecutive nominal channels. If they are not consecutive each subs

45、et of channels have to be considered as an individual pass band. The Repeater can have one or several pass bands. relevant band: frequency band of GSM Repeater declared by the manufacturer according to the designations in table 1-1 repeater: bi-directional Radio Frequency (RF) amplifier which can am

46、plify and transmit a received Mobile Station (MS) signal in the GSM MS transmit band, simultaneously it can amplify and transmit a radiated or conducted received Base Transceiver Station (BTS) RF signal in the GSM BTS transmit band R-GSM: Railways GSM 900 band (includes P-GSM band and E-GSM band) re

47、peater system using frequency shift: repeater system consisting of two different elements, a master unit close to the BTS and at least one remote unit close to the area to be covered NOTE: The master unit amplifies the channels from the BTS and shifts them to different GSM channels. In the remote un

48、it the shifted channels from the master unit will be transferred back to the original channels and amplified. This is valid for the downlink signals as well as for the uplink signals. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ARFCN Absolute Radio

49、Frequency Channel Number BSS Base Station System BTS Base Transceiver Station CW Continuous Wave DCS Digital Cellular System DUT Device Under Test EFTA European Free Trade Association ER-GSM Extended Railways GSM GSM General System for Mobile communications GSM-R GSM RailwayMS Mobile Station RF Radio Frequency RMS Root Mean Square RSS Root Sum of the Squares 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall