ETSI ETS 300 086-1991 Radio Equipment and Systems Land Mobile Service Technical Characteristics and Test Conditions for Radio Equipment with an Internal or External RF Connector In_1.pdf

1、ETS 300 086 January 1991 UDC: 654.16 Key words: land mobile radio, analogue speech, testing Radio Equipment and Systems Land mobile service Technical characteristics and test conditions for radio equipment with an internal or external RF connector intended primarily for analogue speech ETSI European

2、 Telecommunications Standards Institute ETSI Secretariat: B.P. 152 . F - 06561 Valbonne Cedex . France TP. + 33 92 94 42 O0 TF. + 33 93 65 47 16 Tx. 47 O0 40 F _ 8 European Telecommunications Standards Institute 1 991. All rights reserved. No pan may be reproduced or used except as authorised by con

3、tract or other written permission. The COWriQht and the foregoing restriction on reproduction and use extend to all media in which the information may be embodied. Page 2 ETC 300 086:1991 Whilst every care has been taken in the preparation andpublication of this document, errors in content, typograp

4、hical or otherwise, may occur, If you have comments concerning its accuracy, Please write to “ETSI Standards Management Dept.“ at the address shown on the title Daae. . ETSI ETS*3OO 086 91 E 3400855 0150620 522 E Page 3 ETS 300 086:1991 Contents Foreword 7 Introduction . 7 . 1 Scope . 9 2 Definition

5、s. abbreviations and symbols 9 2.1 Definitions 9 2.2 Abbreviations . 10 2.3 Symbols . 10 3 General 10 Presentation of equipment for testing purposes . io Choice of model for type approval 11 Definitions of alignment range and switching range 1 1 Definition of the categories of the alignment range (A

6、R1 and AR2) . 11 Choice of frequencies li Testing of single channel equipment of category AR1 . 11 Testing of single channel equipment of category AR2 . 12 Testing of jwo channel equipment of category AR1 . 12 Testing of two channel equipment of category AR2 . 12 Testing of multi channel equipment (

7、more than two channels) of category AR1 13 Testing of multi channel equipment (more than two channels) of category AR2 (switching range less than alignment range) . 13 Testing of multi channel equipment (more than two channels) of category AR2 (switching range equals the alignment range) . 13 Testin

8、g of equipment without an external 50 RF connector La 13 3.1.12.1 Equipment with a temporary or internal permanent antenna connector . 13 3.1.12.2 Equipment with a temporary antenna connector 14 Mechanical and electrical design . 14 3.2.1 General . 14 3.2.2 Controls 14 3.2.3 Transmitter shut-off fac

9、ility 14 3.2.4 Marking . 14 Interpretation of the measurement results . 14 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 3.1.6 3.1.7 3.1.8 3.1 . 9 3.1.10 3.1.11 3.1.12 4 Technical characteristics 15 Transmitter parameter limits . 15 4.1.1 Frequency error 15 4.1.2 Carrier power (conducted) . 16 4.1.3 Effective radia

10、ted power 16 4.1.4 Frequency deviation . 16 Maximum permissible frequency deviation . 16 Response of the transmitter to modulation frequencies above 3 kHz . 16 4.1.5 Adjacent channel power 17 4.1.6 Spurious emissions 17 4.1.8 Transient frequency behaviour of the transmitter . 18 4.1 4.1.4.1 4.1.4.2

11、4.1.7 Intermodulation attenuation . 18 . ETSI ETS*3DU UBb 91 3400855 0350623 469 = Pago 4 ETS 300 086:1991 4.2 Receiver parameter limits 19 4.2.1 Maximum usable sensitivity . ig 4.2.2 4.2.3 Amplitude characteristic 20 4.2.4 Co-channel rejection 20 4.2.5 Adjacent channel selectivity . 20 4.2.6 Spurio

12、us response rejection 20 4.2.7 Intermodulation response rejection . 20 4.2.8 Blocking or desensitisation 20 4.2.9 Spurious radiations 21 Duplex operation - receiver limits 21 Receiver desensitisation and maximum usable sensitivity . 21 Receiver spurious response rejection . 21 Maximum usable sensiti

13、vity (field strength) 19 4.3 4.3.1 4.3.2 5 Test conditions. power sources and ambient temperatures . 21 Normal and extreme test conditions 21 Test Power source . 22 Normal test conditions 22 Normal temperature and humidity . 22 Normal test power source 22 5.3.2.1 Mains voltage 22 5.3.2.2 Regulated l

14、ead-acid battery power sources used on vehicles . 22 5.3.2.3 Other power sources 22 Extreme test conditions 23 5.4.1 Extreme temperatures 23 5.4.2 Extreme test so.urce voltages . 23 5.4.2.1 Mains voltage . 23 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 23 5.4.2.3 Power sourc

15、es using other types of batteries . 23 5.4.2.4 Other power sources 23 Procedure for tests at extreme temperatures 24 Procedure for equipment designed for continuous operation . 24 Procedure for equipment designed for intermittent operation 24 5.1 5.2 5.3 5.3.1 5.3.2 5.4 5.5 5.5.1 5 . 5 . 2 6 General

16、 conditions 24 Normal test modulation . 24 Artif iciai antenna . 24 Test sites and general arrangements for radiated measurements . 25 Transmitter automatic shut-off facility 25 Arrangement for test signals at the input of the transmitter 25 Arrangements for test signals at me input of the receiver

17、. 25 Receiver mute or squelch facility . 25 Receiver rated audio output power 25 Tests of equipment with a duplex filter . 25 6. 1 6.2 6.3 6.4 6.5 6.6 6 . 7 6.8 6.9 7 Methods of measurement for transmitter parameters . 25 Frequency error . 26 7.1.1 Definition . 26 7.1.2 Method of measurement 26 Carr

18、ier power (conducted) 26 7.2.1 Definitions 26 7.2.2 Method of measurement 26 Effective radiated power (field strength) 26 7.3.1 Definition . 26 7.3.2 Method of measurement 27 7 . 1 7.2 7.3 7.4 7.5 7.6 9.7 Y . 8 - ETSI ETSa300 OBb 71 34001355 01i50622 3T5 W Page 5 ETS 300 086:1991 Frequency deviation

19、 28 Maximum permissible frequency deviation . 28 7.4.1.1 Defin it ion 28 7.4.1.2 Method of measurement . 28 Response of the transmitter to modulation frequencies above 3 kHz . 28 7.4.2.1 Definition 28 7.4.2.2 Method of measurement 28 Adjacent channel power . 29 7.5.1 Definition 29 7.5.2 Methods of m

20、easurement 29 Spurious emissions . 30 7.6.1 Definition 30 7.6.2 Method of measuring the power level in a specified load, subclause 7.6.1 a . 30 7.6.3 Method of measuring the effective radiated power. subclause 7.6.1 b 30 7.6.4 Method of measuring the effective radiated power. subclause 7.6.1 c . 31

21、Intermodulation attenuation 32 7.7.1 Definition 32 7.7.2 Method of meacurement 32 Transient frequency behaviour of the transmitter 33 Definitions . 33 Method of measurement 34 7.4.1 7.4.2 7.8.1 7.8.2 8 Methods of measurement for receiver parameters 37 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 Maximum usab

22、le sensitivity (conducted) 37 8.1.1 Definition 37 8.1.2 Method of measuring the SNDND ratio . 37 Maximum usable sensitivity (field strength) 37 8.2.1 Definition 37 8.2.2 Method of measurement 38 Amplitude characteristic of the receiver 39 8.3.1 Definition 39 8.3.2 Metod of measurement 39 Co-channel

23、rejection . 39 8.4.1 Definition . -39 8.4.2 Method of measurement 39 Adjacent channel selectivity 40 8.5.1 Definition 40 8.5.2 Method of measurement 40 Spurious response rejection . 40 6.6.1 Definition 40 8.6.2 . Introduction to the method of measurement 40 8.6.2.1 Method of search over the “limited

24、 frequency range“ . 41 8 A.2.2 Method of measurement 42 Intermodulation response rejection 42 8.7.1 Definition 42 8.7.2 Method of measurement 42 Blocking or desensitisation . 43 8.8.1 Definition 43 8.8.2 Method of measurement 43 Spurious radiations . 44 . 8.9.1 Definition 44 8.9.2 Method of measurin

25、g the power level in a specified load. subclause 8.9.1 .a 44 8.9.3 Method of measuring the effective radiated power. subclause 8.9.1 .b . 44 8.9.4 Method of measuring the effective radiated power. subclause 8.9.1 . c . 45 - ETSI ETS8300 O06 91 I 3400055 0150623 231 Page 6 ETS 300 086:1991 9 Duplex o

26、peration .45 9.1.1 Definition 45 9.1.2 Method of measurement when the equipment operates with a duplex filter 46 9.1.3 Measuring method when the equipment operates with two antennas 46 9.1 Receiver desensitisation with simultaneous transmission and reception . 45 9.2 Receiver spurious response rejec

27、tion . 46 1 O Measurement uncertainty 47 Annex A (Normative) . 48 A Radiated measurements Test sites and general arrangements for measurements involving the use of radiated fields 48 A.l.l Outdoor test site . 48 Test antenna . 48 A.1.2 Substitution antenna 49 A.1.3 A.l.4 Optional additional indoor s

28、ite 49 50 Guidance on the use of radiation test sites . 50 A.2.1 Measuring distance 50 A.2.2 Test antenna . 50 A.2.3 Substitution wtenna 51 A.2.4 Artificial antenna 51 A.2.5 Auxiliary cables 51 A.2.6 Acoustic measuring arrangement 51 Further optional alternative indoor test site using an anechoic ch

29、amber 51 A.3.1 Example of the construction of a shielded anechoic chamber . 52 A.3.2 Influence of parasitic reflections in anechoic chambers . 52 A.3.3 Calibration of the shielded anechoic chamber . 53 A . 1 A.2 A.3 Annex B (Normative) . 55 Specifications for adjacent channel power measurement arran

30、gements 55 Power measuring receiver specification 55 B.l.1 IF filter 55 0.1.2 Variable attenuator . 57 B.1.3 Rms value indicator . 57 B.1.4 . Oscillator and amplifier . 57 8.1 Annex C . 50 ETSI ETSs300 O86 73 m 3400855 0350624 178 I PIgO 7 ETS 300 086:1991 Foreword This European Telecommunication St

31、andard has been prepared by the Radio Equipment and Systems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI). me draft has undergone the ETSI public enquiry process, and is now published. The standard which is based upon CEPT Recommendation T/R 24-01, is a gene

32、ral standard which may be superseded by specific standards covering specific applications. Angle modulation is used for radio equipment covered by this ETS, but individual national administrations are free to choose the type of modulation. Channel separations, maximum transmitter output power / effe

33、ctive radiated power, class of transmitter intermodulation attenuation and the inclusion of automatic transmitter shut-off facility may all be conditions relating to the issue of a licence by the appropriate administration. P Additional standards or specifications may be required for equipment such

34、as that intended for connection to the public switched telephone network (PSTN). This standard does not cover requirements for radiated emissions below 30 MHz. It is anticipated that methods of measurements and minimum standards for such emissions will be covered by specifications supporting EMC Dir

35、ective 891336 EEC. Annex A provides additional information concerning radiated measurements. Annex B contains normative specifications for adjacent channel power measurement arrangements. Annex C is a graphic representation of the normative subclause 3.1, referring to the presentation of equipment f

36、or testing purposes. Introduction This standard is intended to specify the minimum performance and the methods of measurement of radio equipment for use in the land mobile service as specified in the Scope. Clause 4 provides the corresponding limits. These limits have been chosen to ensure an accept

37、able grade of service and to minimise harmful interference to other equipment and services. They are based on the interpretation of the measurement results described in SubClaus8 3.3. This standard will also be used by accredited test laboratories for the assessment of the performance of the equipme

38、nt. The performance of the equipment submitted for type testing shall be representative for the performance of the Corresponding production model. In order to avoid any ambiguity in that assessment, this standard contains instructions for the presentation of equipment for type testing purposes (clau

39、se 3), conditions (clause 5) and measurement methods (clauses 7 and 8). This standard was drafted on the assumption that: - the type test measurements will be performed oniy once, in one of the accredited test laboratories, and the measurements accepted by the various authorities in order to grant t

40、ype approval, if equipment available on the market is required to be checked it shall be tested in accordance with the methods of measurement specified in this standard. Page 8 ETS 300 086:1991 This standard covers base stations, mobile stations and two categories of hand portable stations. One cate

41、gory is fitted with a 50 n external antenna socket or connector. The other category has no external antenna socket, but: - either it is fitted with a permanent internal 50 n RF connector, - or it can be fitted with a temporary internal 50 RF connector,so that conducted measurements can be performed.

42、 The means to access andior implement the internai connector shall be provided by the manufacturer. Details of the means used during type testing shall be provided by the accredited test laboratory with the test report, subclause 3.1.12. Peg. 9 ETS 300 086:1997 1 Scope This standard covers the minim

43、um characteristics considered necessary in order to make the best use of the available frequencies. It does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. It applies to angle modulation systems fo

44、r use in the land mobile service, operating on radio frequencies between 30 MHz and 1000 MHz, with channel separations of 12.5 kHz. 20 kHz and 25 kHz, and intended primarily for analogue speech. In this standard different requirements are given for the different radio frequency banda, channel separa

45、tions, environment+ conditions and types of equipment, where appropriate. The types of equipment covered by this standard are as follows: - Base station: equipment fitted with an antenna socket. - Mobile station: equipment fitted with an antenna socket. - Handportable stations: a) fitted with an ant

46、enna socket, b) without an external antenna socket (integral antenna equipment) but fitted with a permanent internal or a temporary internal 50 fi R.F. connector which allows access to the transmitter output and the receiver input. For the type of equipment defined in (b) the additional measurements

47、 which shall be made using the equipment antenna connected to the station (and not using any connector) are as follows: - Transmitter effective radiated power - Transmitter radiated spurious emissions - Receiver maximum usable sensitivity (field strength) - Receiver radiated spurious emissions Handp

48、ortable equipment without an external or internal RF connector and without the possibility of having a temporary internai 50 R RF connector is not covered by this standard. 2 Definitions, abbreviations and symbols 2.1 Definitlons For the purpose of this standard. the following definitions appy: Baso

49、 statlon: equipment fitted with an antenna socket, for use with an external antenna, and intended for use in a fixed location. Mobilo station: mobile equipment fitted with an antenna socket, for use with an external antenna, normally used in a vehicle or as a transportable station. Handportablo station: equipment either fitted with an antenna socket or an integral antenna. or both, normally used on a stand-alone basis, to be carried on a person or held in the hand. ETSI ETSk300 O86 93 M 3400855 0350627 987 M Page 10 ETS 300 086:1991 Integral antenna: an antenna d