ETSI ETS 300 374-5-1996 Intelligent Network (IN) Intelligent Network Capability Set 1 (CS1) Core Intelligent Network Application Protocol (INAP) Part 5 Protocol Specification for t_1.pdf

1、ETS 300 374-5 November 1996 Source: ETSI TC-SPS Reference: DEEPS-03032-1 ICs: 33.080, 35.100.70 Key words: IN, CS1, INAP Intelligent Network (IN); Intelligent Network Capability Set 1 (CSI); Core Intelligent Network Application Protocol (INAP); Part 5: Protocol specification for the Service Control

2、Function (SCF) - Service Data Function (SDF) interface ETSI European Telecommunications Standards institute ETSI Secretariat Postai address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - Sophia Antipolis - Vaibonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretana

3、t - Internet: secretariatQetsi.fr Tel.: +33 4 92 94 42 O0 - Fax: +33 4 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards In

4、stitute 1996. All rights reserved. STD-ETSI ETS 300 374-5-ENGL L77b 3400855 OLb12L T44 Page 2 ETS 300 374-5: November 1996 Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments concerning i

5、ts accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. STD-ETSI ETS 300 37Li-5-ENGL L97b m 3400855 OLbL292 780 m Page 3 ETS 300 374-5: November 1996 Contents Foreword . 5 1 Scope 7 2 Normative references 7 3 Abbreviations . 7 4 Segmentation an

6、d re-assembly of INAP messages 8 5 IN X.500 directory access protocol subset 8 6 SCF and SDF Finite State Machines (FSMs) 8 7 SDF operations and errors 8 8 SDL diagrams for SCF and SDF FSMs 8 History 9 STD-ETSI ETS 300 374-5-ENGL L77b 3Li00855 OLbL273 AL7 = Page 4 ETS 300 374-5: November 1996 Blank

7、page STD-ETSI ETS 300 37Li-5-ENGL Lb m 3400855 OLbL294 753 = Page 5 ETS 300 374-5: November 1996 Foreword This European Telecommunication Standard (ETS) has been produced by the Signalling Protocols and Switching (SPS) Technical Committee of the European Telecommunications Standards Institute (ETSI)

8、. This ETS is based on the latest version of ITU-T Recommendation Q.1218. This ETS is part 5 of a rnulti-part standard covering the Capability Set 1 (CS1) core Intelligent Network Protocol (INAP) as described below: Part 1: “Protocol specif cation“; Part 2: “Protocol Implementation Conformance State

9、ment (PICS) proforma specification“; Part 3: “Test Suite Structure and Test Purposes (TSS Part 4: “Abstract Test Suite (ATS) and partial Protocol Implementation extra Information for Testing (PIXIT) proforma specification for SSF and SRF“; Part 5: “Protocol specification for the Service Control Func

10、tion (SCF) - Service Data Function (SDF) interface“; Part 6: “PICS proforma specification for the SCF-SDF interface“ NOTE: Further parts may be identified after the publication of this ETS. Transposition dates Date of adoption Date of latest announcement of this ETS (doa): 22 November 1996 28 Februa

11、ry 1997 Date of latest publication of new National Standard or endorsement of this ETS (dop/e): 31 August 1997 I I Date of withdrawal of any conflicting National Standard (dow): 31 August 1997 STD.ETS1 ETS 300 37Li-5-ENGL L99b 3900855 OlbL295 b7T Page 6 ETS 300 374-5: November 1996 Blank page STDmET

12、SI ETS 300 379-5-ENGL L99b m 3i00855 ULbL29b 52b m Page 7 ETS 300 374-5: November 1996 1 Scope This fifth part of ETS 300 374 provides an extension of the core Intelligent Network Application Protocol (INAP) of Intelligent Network (IN) Capability Set 1 (CS1) as specified in ETS 300 374-1 4. It suppo

13、rts interactions between the following two Functional Entities (FES), as defined in the IN functional model: - Service Control Function (SCF); - Service Data Function (SDF). This ETS is intended as a guide to implementors and network operators to ensure interworking between different manufacturers e

14、quipment for the IN CS1 SCF-SDF interface and between network operators for the same interface. 2 Normative references This ETS incorporates by dated and undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publicat

15、ions are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. 121 131 41 ITU-T Recommendati

16、on Q.1218 (1 995): “Interface Recommendation for intelligent network CS-1 l. ETC 300 009-1 : “Integrated Services Digital Network (ISDN); Signalling System N0.7; Signalling Connection Control Part (SCCP) (connectionless and connection-oriented class 2) to support international interconnection; Part

17、1 : Protocol specification ITU-T Recommendations Q.711 to (2.714 and Q.716 (1 993), modified“. ETS 300 287-1 : “Integrated Services Digital Network (ISDN); Signalling System No.7; Transaction Capabilities (TC) version 2; Part 1 : Protocol specification ITU-T Recommendations Q.771 to Q.775 (1 993), m

18、odified“. ETS 300 374-1 (1 994): “Intelligent Network (IN); Intelligent Network Capability Set 1 (CSl); Core Intelligent Network Application Protocol (INAP); Part 1: Protocol specification“. 3 Abbreviations For the purposes of this ETS, the following abbreviations apply: cs1 FE FSM IN INAP SCF SDF S

19、DL Capability Set 1 Functional Entity Finite State Machine Intelligent Network Intelligent Network Application Protocol Service Control Function Service Data Function Specification and Description Language STD-ETSI ETS 300 374-5-ENGL L77b 3Li00855 OLb1277 qb2 D Page 0 ETS 300 374-5: November 1996 4

20、Segmentation and re-assembly of INAP messages If segmentation and re-assembly of INAP messages is required on the SCF-SDF interface due to the length of messages, the segmentation and re-assembly procedures for SCCP connectionless messages as specified in ETS 300 009-1 2 shall be used. 5 IN X.500 di

21、rectory access protocol subset The text of ITU-T Recommendation Q.1218 l subclause 2.2 is endorsed by ETSI with the following modifications: All references to ITU-T Recommendations Q.771, Q.772, Q.773, Q.774 and Q.775 shall be replaced by references to ETS 300 287-1 3. 6 SCF and SDF Finite State Mac

22、hines (FSMs) The text of ITU-T Recommendation Q.1218 l subclauses 3.1.2.5.5 and 3.1.4 is endorsed by ETSI with the following modifications: All references to ITU-T Recommendation Q.771 shall be replaced by references to ETS 300 287-1 3 and all references to ITU-T Recommendation Q.711 shall be replac

23、ed by references to EIS 300 009-1 121. 7 SDF operations and errors The text of ITU-T Recommendation Q.1218 l subclauses 3.2.1.1, 3.2.1.8, 3.2.1.11, 3.2.1.12, 3.2.1.21, 3.3.3,3.3.9, 3.3.27, 3.3.35,3.3.42 and 3.3.54 is endorsed by ETSI. 8 SDL diagrams for SCF and SDF FSMs The text of ITU-T Recommendat

24、ion Q.1218 l annex B is endorsed by ETSI. STD-ETSI ETS 300 374-5-ENGL 1776 E 3400855 0363278 3T9 9 Page 9 ETS 300 374-5: November 1996 History August 1995 September 1996 November 1996 Document history Public Enquiry PE 89: 1 995-08-07 to 1 995-1 2-01 Vote v 111: 1996-09-23 to 1996-1 1-1 5 First Edition ISBN 2-7437-0414-4 - Edition complte ISBN 2-7437-1 152-3 - Partie 5 Dpt lgal : Novembre 1996