ETSI GSM 02 02-1996 Digital Cellular Telecommunications System (Phase 2+) Bearer Services (BS) Supported by a GSM Public Land Mobile Network (PLMN)《数字蜂窝通信系统(第2+阶段) GSM公共陆地移动网(PLMN).pdf

1、* ETSI 6SM*Q2-02 96 U 3400855 0305540 495 m ETSI GSM GSM 02.02 May 1996 Version 5.1 .O Source: ETSI TC-SMG Reference: TS/SMG-O10202QR ICs: 33.060.50 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS Digital ce

2、llular telecommunications system (Phase 2+); Bearer Services (BS) supported by a GSM Public Land Mobile Network (PLMN); (GSM 02.02) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - S

3、ophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariatetsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend

4、 to reproduction in all media. O European Telecommunications Standards Institute 1996. All rights reserved. ETSI GSM*02.02 96 W 3400855 0105541 321 W Page 2 GSM 02.02 Version 5.1 .O: May 1996 Whilst every care has been taken in the preparation and publication of this document, errors in content, typ

5、ographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. ETSI GSM*02.02 9b 3400855 0305542 268 = Page 3 GSM 02.02 Version 5.1.0: May 1996 Contents Foreword 5 O Scope . 0.1 Norm

6、ative references 7 0.2 Abbreviations . 8 1 Framework for defining bearer services 8 2 Bearer service categories 1 O 3 Bearer services . 11 History . . 14 I ETSI GSM+02.02 96 m 3400855 0305543 IT4 m I Page 4 GSM 02.02 Version 5.1 .O: May 1996 Bian k page ETSI GSM*O2-02 9b 3409855 0305544 030 Page 5 G

7、SM 02.02 Version 5.1 .O: May 1996 Foreword This Global System for Mobile communications Technical Specification (GTS) has been produced by the Special Mobile Group (SMG) Technical Committee (TC) of the European Telecommunications Standards Institute (ETSI). This GTS defines a set of bearer services

8、to be provided within the digital cellular telecommunications system (Phase 2/Phase 2+). This GTS is a TC-SMG approved GSM technical specification version 5, which contains GSM Phase 2+ enhancementdfeatures to the version 4 GSM technical specification. The ETS on which this Phase 2+ GTS is based is

9、Phase 2 GSM ETS 300 501 (GSM 02.02 version 4.2.2). GTS are produced by TC-SMG to enable the GSM Phase 2 + specifications to become publicly available, prior to submission for the formal ETSI standards approval procedure to become European Telecommunications Standards (ETS). This ensures the earliest

10、 possible access to GSM Phase 2 + specifications for all Manufacturers, Network operators and implementors of the Global System for Mobile communications. The contents of this GTS are subject to continuing work within TC-SMG and may change following formal TC-SMG approval. Should TC-SMG modify the c

11、ontents of this GTS it will then be republished by ETSI with an identifying change of release date and an increase in version number as follows: Version 5.x.y where: y the third digit is incremented when editorial only changes have been incorporated in the specification; x the second digit is increm

12、ented for all other types of changes, .e. technical enhancements, corrections, updates, etc. The specification from which this GTS has been derived was originally based on CEPT documentation, hence the presentation of this GTS may not be entirely in accordance with the ETSI rules. Reference is made

13、within this TS to GSM-TSs (note). NOTE: TC-SMG has produced documents which give the technical specifications for the implementation of the digital cellular telecommunications system. Historically, these documents have been identified as GSM Technical Specifications (GSM-TSs). These TSs may have sub

14、sequently become I-ETSs (Phase I), or ETSs/ETSI Technical Reports (ETRs) (Phase 2). TC-SMG has also produced ETSI GSM TSs which give the technical specifications for the implementation of Phase 2+ enhancements of the digital cellular telecommunications system. These version 5.x.x GSM Technical Speci

15、fications may be referred to as GTSs. ETSI GSM*O2.02 %b H 3400655 0305545 T77 Page 6 GSM 02.02 Version 5.1 .O: May 1996 Blank page ETSI GSM*Q2-02 96 9 34Cl0855 OLO55Yb 903 U Page 7 GSM 02.02 Version 5.1 .O: May 1996 O Scope The purpose of this specification is to define a set of bearer services to b

16、e provided to GSM PLMN subscribers by a GSM PLMN itself and in connection with other networks. This specification should also be used as a reference for defining the corresponding required mobile network capabilities which are specified by means of the “GSM PLMN connection type“ concept, defined in

17、GSM 03.10. The recommended provision of the bearer services is under the control of the GSM MOU and is out of the scope of ETSI TC-SMG. Bearer services not included in this specification that require modifications to the GSM signalling specifications should not be introduced unilaterally by a mobile

18、 network operator. o. 1 Normative references This GTS incorporates by dated and undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to

19、or revisions of any of these publications apply to this GTS only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. 91 GSM O1 .O4 (ETR 100): “Digital cellular telecommunication system (Phase 2); Abbreviations and acron

20、yms“. GSM 02.01 (ETS 300 500): “Digital cellular telecommunication system (Phase 2); Principles of telecommunication services supported by a GSM Public Land Mobile Network (PLMN)“. GSM 02.04 (ETS 300 503): “Digital cellular telecommunication system (Phase 2); General on supplementary service“. GSM 0

21、3.10 (ETS 300 528): “Digital cellular telecommunication system (Phase 2); GSM Public Land Mobile Network (PLMN) connection types“. GSM 04.02 (ETS 300 551): “Digital cellular telecommunication system (Phase 2); GSM Public Land Mobile Network (PLMN) access reference configuration“. GSM 07.01 (ETS 300

22、582): “Digital cellular telecommunication system (Phase 2); General on Terminal Adaptation Functions (TAF) for Mobile Stations (MS)“. GSM 07.02 (ETS 300 583): “Digital cellular telecommunication system (Phase 2); Terminal Adaptation Functions (TAF) for services using asynchronous bearer capabilities

23、“. GSM 07.03 (ETS 300 584): “Digital cellular telecommunication system (Phase 2); Terminal Adaptation Functions (TAF) for services using synchronous bearer capabilities“. GSM 07.05 (ETS 300 585): “Digital cellular telecommunication system (Phase 2); Use of Data Terminal Equipment (DTE)/Data Circuit

24、terminating Equipment (DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS)“. GSM 09.02 (ETS 300 599): “Digital cellular telecommunication cysiem (Phase 2); Mobile Application Part (MAP) specification“. GSM 09.03 (ETS 300 600): “Digital cellular telecommunication system (P

25、hase 2); Signalling requirements on interworking between the Intergrated Services Digital Network (ISDN) or Public Switched Telephone Network (PSTN) and the Public Land Mobile Network (PLMN)“. ETSI GSM*02.02 96 3400855 0305547 84T Page 8 GSM 02.02 Version 5.1 .O: May 1996 i 31 i 41 GSM 09.04 (EIS 30

26、0 601): “Digital cellular telecommunication system (Phase 2); Interworking between the Public Land Mobile Network (PLMN) and the Circuit Switched Public Data Network (CSPDN)“. GSM 09.05 (ETS 300 602): “Digital cellular telecommunication system (Phase 2); Interworking between the Public Land Mobile N

27、etwork (PLMN) and the Packet Switched Public Data Network (PSPDN) for Packet Assembly/Disassembly facility (PAD) access“. GSM 09.06 (ETS 300 603): “Digital cellular telecommunication system (Phase 2); Interworking between a Public Land Mobile Network (PLMN) and a Packet Switched Public Data Networkh

28、tergrated Services Digital Network (PSPDNASDN) for the support of packet switched data transmission services“. GSM 09.07 (ETS 300 604): “Digital cellular telecommunication system (Phase 2); General requirements on interworking between the Public Land Mobile Network (PLMN) and the Intergrated Service

29、s Digital Network (ISDN) or Public Switched Telephone Network (PSTN)“. GSM 09.1 O (ETS 300 605): “Digital cellular telecommunication system (Phase 2); Information element mapping between Mobile Station - Base Station System and BSS - Mobile-services Switching Centre (MS-BSS-MSC) Signalling procedure

30、s and the Mobile Application Part(MAP)“. GSM 09.1 1 (ETS 300 606): “Digital cellular telecommunication system (Phase 2); Signalling interworking for supplementary services“. CCITT Recommendation V.120: “Support by an ISDN of data terminal equipments with V-series type interface with provisoin for st

31、atistical multiplexing“. 0.2 Abbreviations Abbreviations used in this specification are listed in GSM 01.04. 1 Framework for defining bearer services Bearer services are described by attributes, which are intended to be independent. These attributes are described and defined in GSM 02.01. They are g

32、rouped into four categories: i) Information transfer attributes, which characterise the network capabilities for transferring information from a user access point in a GSM PLMN to a user access point in another network. (Refer to GSM 02.01 and 04.02 for definitions of user access points, originating

33、 and terminating networks.) i) Access attributes, which describe the means for accessing network functions or facilities as seen at the access point in the PLMN (see GSM 02.01). iii) Interworking attributes, which describe properties of the terminating network and its access point. The terminating n

34、etwork may include another GSM PLMN or the originating PLMN (see GSM 02.01). iv) General attributes, which deal with the service in general. Figure I/GSM 02.02 shows the relation between the groups of attributes and their fields of applicability. 3 ETSI GSM*02.02 9b = 3400855 0105548 786 Page 9 GSM

35、02.02 Version 5.1 .O: May 1996 Information Transfer and Access Attributes (Note 3) i - -+ I General Attributes (NOTE 2) NOTE 1 : A transit network may not exist for a bearer service. NOTE 2: Communication may be established from either end. NOTE 3: The information transfer and access attributes of a

36、 bearer service relate to a direct peer-to-peer communication of: - TE tTE, - TE to a network gateway (supporting,for example, PSTN interworking), or - network gateway to a TE. Figure l/GSM 02.02: Relation between the groups of attributes and fields of applicability The following table lists the ind

37、ividual attributes in each of the four groups. The GSM bearer service definitions in this specification are based on the “Minimal Set“ of attributes. ETSI GSM*02=02 9b E 3400855 0305549 bL2 Page 10 GSM 02.02 Version 5.1 .O: May 1996 Table l/GSM 02.02: List of bearer service attributes Minimal set I

38、Information Transfer Attributes Information Transfer Mode X Information Transfer Rate X information Transfer Capability X Establishment of Communication X Symmetry X. Communication Configuration X Data Compression Access Channel and Rate Access Attributes Signalling Access Protocols Information Acce

39、ss Protocols Information Access Structure X Information Access Rate X Interworking Attributes General Attributes Supplementary Services Provided Operational and Commercial Quality of Service X Attributes that are not part of the minimal set provide further technical detail and are required to fully

40、define the use of each bearer service. See the GSM 07-series specifications for information about the Signalling Access Protocols, Information Access Protocols and related access attributes. GSM supplementary services are defined in GSM 02.04. Intercommunication is required with services in the PSTN

41、, ISDN, CSPDN and other PLMNs. The capabilities that describe the Interworking Attributes are described in GSM 03.10 and the GSM 09-series specifications. 2 Bearer service categories All bearer service categories provide information transfer between R/S reference points and allow the use of sub-rate

42、 information streams which are rate-adapted. The bearer services can be grouped into the following categories: - Unrestricted Digital Information (UDI); Provides the transfer of unrestricted digital information. - 3.1 kHz (External to the PLMN); Used to select a “3.1 kHz audio“ interworking function

43、 at the MSC. This service category is used when interworking with the ISDN or PSTN “3.1 kHr audio“ service and includes the capability to select a modem at the interworking function. “External to the PLMN“ indicates that the “3.1 kHz audio“ service is only used outside of the PLMN, in the ISDN/PSTN.

44、 The connection within the PLMN, user access point to the interworking function, is an unrestricted digital connection. PAD; Provides an asynchronous connection to a PAD. This enables PLMN subscribers to access a packet network (PSPDN/ISDN). See GSM TS 09.05 for service and interworking specificatio

45、ns. ETSI GSM*02.02 b 3480855 0305550 334 Page 11 GSM 02.02 Version 5.1 .O: May 1996 Provides a synchronous connection that enables PLMN subscribers to access a packet network (PSPDNISDN). See GSM TS 09.06 for service and interworking specifications. - Packet; - - Alternate Speech/Data; Provides the

46、capability to swap between speech and data during a call. BSS - MSC 1F Mobile Station If either the speech or data portion of the call requires a full rate channel, a full rate channel shall be used for the duration of the call. The access interface at the mobile station for the data portion is assu

47、med to be a standard data interface. Some means must be provided to select the speech/data capability. - Speech followed by Data; Provides a speech connection first and then at some time while the call is in progress, the user can switch to a data connection. The user cannot switch back to speech af

48、ter the data portion. If either the speech or data portion of the call requires a full rate channel, a full rate channel shall be used from the start of the call. The network may then change to a half rate channel for the data portion. 3 Bearer services This section provides a list of the existing G

49、SM bearer services and indicates the values for each attribute in the minimal set. The following attributes have the same value for all GSM bearer services. Their values are as follows: Information Transfer Mode: “Circuit“ Information Transfer Rate: Establishment of Communication: “Demand“ Symmetry: “Bi-directional Symmetric“ (NOTE 2) Communication Configuration: “Point to point“ Not applicable (NOTE 1) NOTE 1: The Information Transfer Rate attribute is not applicable because it depends on the reference point assumed in the GSM PLMN, transit or terminating network. NOTE 2: Asynchron