ETSI GSM 03 09-1996 Digital Cellular Telecommunications System (Phase 2+) Handover Procedures《参见ETS 300 527(版本4 6 0)》.pdf

1、ETSI GSM*O3-09 46 3400855 0305673 BI2 * GSM GSM 03.09 May 1996 Version 5.0.0 Source: ETSI TC-SMG Reference: TS/SMG-O30309Q ICs: 33.060.50 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS Digital cellular tele

2、communications system (Phase 2+); Handover procedures (GSM 03.09) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi,

3、s=secretariat - Internet: secretariat8etsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Stan

4、dards Institute 1996. All rights reserved. * COPYRIGHT European Telecommunications Standards InstituteLicensed by Information Handling ServicesETSI GSM*O3.09 96 m 3400855 OL05b74 759 m Page 2 GSM 03.09 Version 5.0.0: May 1996 Whilst every care has been taken in the preparation and publication of thi

5、s document, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Standards Approval Dept.“ at the address shown on the title page. COPYRIGHT European Telecommunications Standards InstituteLicensed by Information Han

6、dling ServicesETSI GSM*O3*09 96 H 3400855 0305675 b95 H Page 3 GSM 03.09 Version 5.0.0: May 1996 Contents Foreword . 5 5 6 7 8 9 10 Scope 7 Normative references 8 Definitions and abbreviations 12 Role. functional composition of MSCs and interfaces for handover 13 Role of MSC-A . 13 Functional compos

7、ition of MSC-A and its interfaces for handover . 13 Role of MSC-B . 16 Functional composition of MSC-B and its interfaces for handover . 16 4.1 MSC-A . 13 4.1.1 4.1.2 4.2.1 4.2.2 4.2 MSC-B . 16 Handover initiation conditions 18 General description of the procedures for intra . MSC handovers 18 6.1 P

8、rocedure for Intra-MSC Handovers . 18 General description of the procedures for inter . MSC handovers 21 7.1 7.2 Basic handover procedure not requiring the establishment of a circuit connection between MSC-A and MSC-B . 23 7.3 Procedure for subsequent handover requiring a circuit connection between

9、MSC-A and MSC-B . 24 7.3.1 Description of subsequent handover procedure i): MSC-B to MSC.A . 25 7.3.2 Description of the subsequent handover procedure i): MSC-B to MSC.B 26 Procedure for subsequent handover not requiring a circuit connection between MSC-A and MSC-B . 27 7.4.1 Description of the subs

10、equent handover procedure without circuit connection i): MSC-B to MSC-A . 28 7.4.2 Description of the subsequent handover procedure without circuit connection i): MSC-B to MSC-B 28 Basic handover procedure requiring a circuit connection between MSC-A and MSC-6 21 7.4 Detailed procedures in MSC-A . 3

11、0 8.1 BSS/MSC and MS/MSC procedures in MSC-A (functional unit 1) 30 8.2 Call control procedures MSC-A (functional unit 2) 30 8.3 Handover control procedures MSC-A (functional unit 3) 32 8.4 MAP procedures in MSC-A (functional unit 4) 33 8.5 Interworking between Handover control procedures and MAP pr

12、ocedures in MSC.A 33 8.6 Compatibility with GSM Phase 1 33 Detailed procedures in MSC-B . 34 BSS/MSC (MS/BSS) procedures MSC-B (functional unit 1) 34 Handover control procedures MSC-B (functional unit 3) 35 9.1 9.2 9.3 9.4 9.5 9.6 Call control procedures MSC-B (functional unit 2) 34 MAP procedures M

13、SC-B (functional unit 4) . 36 Interworking between Handover control procedures and MAP procedures in MSC-B 36 Compatibility with GSM Phase 1 36 Subsequent channel assignment using a circuit connection between MSC-A and MSC-B . 37 COPYRIGHT European Telecommunications Standards InstituteLicensed by I

14、nformation Handling Servicesl ETSI GSfl*03-09 9b m 3400855 OL05b7b 521 m Page 4 GSM 03.09 Version 5.0.0: May 1996 11 12 SDL diagrams . 40 Directed retry handover . 38 History . 85 COPYRIGHT European Telecommunications Standards InstituteLicensed by Information Handling ServicesETSI GSM+03*09 96 D 34

15、00855 0105677 468 I Page 5 GSM 03.09 Version 5.0.0: May 1996 Foreword This Global System for Mobile communications Technical Specification (GTS) has been produced by the Special Mobile Group (SMG) Technical Committee (TC) of the European Telecommunications Standards Institute (ETSI). This GTS provid

16、es a mechanism giving reliable transfer of signalling messages within the digital cellular telecommunications system (Phase 2Phase 2+). This GTS is a TC-SMG approved GSM technical specification version 5, which contains GSM Phase 2+ enhancementdfeatures to the version 4 GSM technical specification.

17、The ETS from which this Phase 2+ GTS has evolved is Phase 2 GSM 03.09 version 4.6.0. GTS are produced by TC-SMG to enable the GSM Phase 2 + specifications to become publicly available, prior to submission for the formal ETSI standards approval procedure to become European Telecommunications Standard

18、s (ETS). This ensures the earliest possible access to GSM Phase 2 + specifications for all Manufacturers, Network operators and implementors of the Global System for Mobile communications. The contents of this GTS are subject to continuing work within TC-SMG and may change following formal TC-SMG ap

19、proval. Should TC-SMG modify the contents of this GTS it will then be republished by ETSI with an identifying change of release date and an increase in version number as follows: Version 5.x.y where: y the third digit is incremented when editorial only changes have been incorporated in the specifica

20、tion; x the second digit is incremented for all other types of changes, .e. technical enhancements, corrections, updates, etc. NOTE: TC-SMG has produced documents which give the technical specifications for the implementation of the digital cellular telecommunications system. Historically, these doc

21、uments have been identified as GSM Technical Specifications (GSM-TSs). These TSs may have subsequently become I-ETSs (Phase I), or ETSsIETSI Technical Reports (ETRs) (Phase 2). TC-SMG has also produced ETSI GSM TSs which give the technical specifications for the implementation of Phase 2+ enhancemen

22、ts of the digital cellular telecommunications system. These version 5.x.x GSM Technical Specifications may be referred to as GISS. COPYRIGHT European Telecommunications Standards InstituteLicensed by Information Handling ServicesETSI GSN*O3=07 76 m 3400855 0305678 3T4 m Page 6 GSM 03.09 Version 5.0.

23、0: May 1996 Blank page COPYRIGHT European Telecommunications Standards InstituteLicensed by Information Handling ServicesETSI GSM*03*09 96 m 3400855 0105b79 230 m Page 7 GSM 03.09 Version 5.0.0: May 1996 1 Scope This Global System for Mobile communications Technical Specification (GTS) contains a de

24、tailed description of the handover procedures to be used in GSM PLMNs. The purpose of the handover procedures, as described in this specification, are to ensure that the connection to the MS is maintained as it moves from one BSS area to another. This specification considers the following two cases:

25、 i) Handover between Base Stations connected to the same MSC, this is termed an Intra-MSC handover. i) Handover between Base Stations connected to different MSCs, this is termed an Inter-MSC handover. This category can be sub-divided into three further procedures: a) the Basic Inter-MSC Handover pro

26、cedure, where the MS is handed over from a controlling MSC (MSC-A) to another MSC (MSC-B); b) the Subsequent Inter-MSC Handover procedure, where the MS is handed over from MSC-B to a third MSC (MSC-B); c) the Subsequent Inter-MSC handback, where the MS is handed back from MSC-B to MSC-A. In both cas

27、es i) and i) the same procedures as defined in the TS GSM 08.08 and the TS GSM 04.08 shall be used on the A-interface and on the Radio Interface, respectively. In case i) the handover procedures shall transport the A-interface messages between MSC-A and MSC-B described in the Mobile Application Part

28、 (MAP), Technical Specification GSM 09.02. The split in functionality between the BSS and MSC is described in the GSM 08 series of Technical Specifications. The interworking between the GSM 09.02 protocol and the GSM 08.08 protocol is described in the GSM 09.1 O Technical Specification. Handovers wh

29、ich take place on the same MSC are termed Intra-MSC handovers; this includes both Inter- BSS and Intra-BSS handovers. This technical specification also covers the requirements for handover in ongoing voice group calls, directed retry and the handover without a circuit connection between MSC-A and MS

30、C-B. This technical specification does not consider the case of handovers between radio channels on the same BSS (Intra- BSS handover) or the handover of packet radio services. For voice broadcast calls, the speaker uses normal point-to-point handover procedures, whilst the listeners use idle mode c

31、ell reselection procedures, as for the voice group call listeners. Inter-MSC hand-over imposes a few limitations on the system. After inter-MSC hand-over: - call re-establishment is not supported. The list of GSM 08.08 features supported during and after Inter-MSC handover is given in TS GSM 09.08.

32、In the Inter-MSC handover case, the interworking between a Phase 1 BSSMAP protocol possibly used by one MSC and the Phase 2 BSSMAP protocol used in the Phase 2 MAP protocol on the E-interface is performed by this MSC. NOTE: The message primitive names used in the SDL diagrams and message flows in th

33、is technical specification do not represent the actual messages specified in the GSM 04 and GSM 08 series or the services specified in the GSM O9 series of technical specifications. The primitive names are only intended to be indicative of their use in this document. COPYRIGHT European Telecommunica

34、tions Standards InstituteLicensed by Information Handling ServicesETSI GSM*03.09 96 m 3400855 0305680 T52 m Page 8 GSM 03.09 Version 5.0.0: May 1996 2 Normative references This GTS incorporates by dated and undated reference, provisions from other publications. These normative references are cited a

35、t the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this GTS only when incorporated in it by amendment or revision. For undated references, the latest edition of the publicat

36、ion referred to applies. i31 41 51 71 191 o1 11 31 i 41 GSM O1 .O4 (ETR 100): “Digital cellular telecommunications system (Phase 2); Abbreviations and acronyms“. GSM 04.01 (ETS 300 550): “Digital cellular telecommunications system (Phase 2); Mobile Station - Base Station System (MS - BSS) interface

37、General aspects and principles“. GSM 04.02 (ETS 300 551): “Digital cellular telecommunications system (Phase 2); GSM Public Land Mobile Network (PLMN) access reference configuration“. GSM 04.03 (ETS 300 552): “Digital cellular telecommunications system (Phase 2); Mobile Station - Base Station System

38、 (MS - BSS) interface Channel structures and access capabilities“. GSM 04.04 (ETS 300 553): “Digital cellular telecommunications system (Phase 2); layer 1 General requirements“. GSM 04.05 (ETS 300 554): “Digital cellular telecommunications system (Phase 2); Data Link (DL) layer General aspects“. GSM

39、 04.06 (ETS 300 555): “Digital cellular telecommunications system (Phase2); Mobile Station - Base Station System (MS - BSS) interface Data Link (DL) layer specification“. GSM 04.07 (ETS 300 556): “Digital cellular telecommunications system (Phase 2); Mobile radio interface signalling layer 3 General

40、 aspects“. GSM 04.08 (ETS 300 557): “Digital cellular telecommunications system (Phase 2); Mobile radio interface layer 3 specification“. GSM 04.1 O (ETS 300 558): “Digital cellular telecommunications system (Phase 2); Mobile radio interface layer 3 Supplementary services specification General aspec

41、ts“. GSM 04.1 1 (ETS 300 559): “Digital cellular telecommunications system (Phase 2); Point-to-Point (PP) Short Message Service (SMS) support on mobile radio interface“. GSM 04.1 2 (ETS 300 560): “Digital cellular telecommunications system (Phase2); Short Message Service Cell Broadcast (SMSCB) suppo

42、rt on the mobile radio interface“. GSM 04.1 3 (ETS 300 561): “Digital cellular telecommunications system (Phase 2); Performance requirements on mobile radio interface“. GSM 04.21 (ETS 300 562): “Digital cellular telecommunications system (Phase 2); Rate adaption on the Mobile Station - Base Station

43、System (MS - BSS) interface“. COPYRIGHT European Telecommunications Standards InstituteLicensed by Information Handling ServicesETSI GSM*O3.09 96 m 3400855 8305683 999 m ti 51 Page 9 GSM 03.09 Version 5.0.0: May 1996 GSM 04.22 (ETS 300 563): “Digital cellular telecommunications system (Phase2); Radi

44、o Link Protocol (RLP) for data and telematic services on the Mobile Station - Base Station System (MS - BSS) interface and the Base Station System - Mobile-services Switching Centre (BSS - MSC) interface“. GSM 04.80 (ETS 300 564): “Digital cellular telecommunications system (Phase 2); Mobile radio i

45、nterface layer 3 supplementary services specification Formats and coding“. GSM 04.81 (ETS 300 565): “Digital cellular telecommunications system (Phase 2); Line identification supplementary services - Stage 3“. GSM 04.82 (ETS 300 566): “Digital cellular telecommunications system (Phase 2); Call Forwa

46、rding (CF) supplementary services - Stage 3“. GSM 04.83 (ETS 300 567): “Digital cellular telecommunications system (Phase 2); Call Waiting (CW) and Call Hold (HOLD) supplementary services - Stage 3“. GSM 04.84 (ETS 300 568): “Digital cellular telecommunications system (Phase 2); MultiParty (MPTY) su

47、pplementary services - Stage 3“. GSM 04.85 (ETS 300 569): “Digital cellular telecommunications system (Phase 2); Closed User Group (CUG) supplementary services - Stage 3“. GSM 04.86 (ETS 300 570): “Digital cellular telecommunications system (Phase 2); Advice of Charge (AOC) supplementary services -

48、Stage 3“. GSM 04.88 (ETS 300 571): “Digital cellular telecommunications system (Phase 2); Call Barring (CB) supplementary services - Stage 3“. GSM 04.90 (ETS 300 572): “Digital cellular telecommunications system (Phase 2); Unstructured supplementary services operation - Stage 3“. GSM 05.01 (EIS 300

49、573): “Digital cellular telecommunications system (Phase 2); Physical layer on the radio path General description“. GSM 05.02 (ETS 300 574): “Digital cellular telecommunications system (Phase 2); Multiplexing and multiple access on the radio path“. GSM 05.03 (ETS 300 575): “Digital cellular telecommunications system (Phase 2); Channel coding“. GSM 05.04 (ETS 300 576): “Digital cellular telecommunications system (Phase 2); Modulation“. GSM 05.05 (EIS 300 577): “Digital cellular telecommunications system (Phase 2); Radio transmission and reception“. GSM 05.08 (ETS 300 578):