ETSI GSM 07 02-1996 Digital Cellular Telecommunications System (Phase 2+) Terminal Adaptation Functions (TAF) for Services Using Asynchronous Bearer Capabilities《数字蜂窝通信系统(第2+阶段) 使用_1.pdf

1、GSM 1 ECHNICAL n GSM 07.02 May 1996 Version 5.1 .O * Source: ETSI TC-SMG Reference: TS/SMG-O40702QR ICs: 33.060.50 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS Digital cellular telecommunications system (

2、Phase 2+); Terminal Adaptation Functions (TAF) for services using asynchronous bearer capabilities (GSM 07.02) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - Sophia Antipolis - Val

3、bonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat etsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in

4、all media. Q European Telecommunications Standards Institute 1996. All rights reserved. ETSI GSM*07.02 b 3400855 0309856 Lb4 m Page 2 GSM 07.02 Version 5.1 .O: May 1996 . . Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or other

5、wise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. ETSI GSfl*07=02 96 3400855 0309857 OTO Page 3 GSM 07.02 Version 5.1.0: May 1996 Contents Foreword . 5 1 Scope 7 1.1 Normative references 7

6、 1.3 Abbreviations 9 2 Reference Configuration 9 Customer Access Configuration 9 Terminal Adaptation Function . 9 2.1 2.2 3 Terminal Adaptation Functions for transparent services 10 3.1 Rate Adaptation 10 3.1.1 Rate Adaptation . V series 10 3.1.2 Rate Adaptation - S Interface (1.420) . 10 Interchang

7、e Circuit Signalling Mapping 10 Interface Signal Levels 10 Call Establishment Signalling Mapping . 11 3.4.1 Autocalling/answering . 11 3.4.2 S Interface (1.420) Signalling Mapping 11 3.4.3 Call Establishment Manual Operation - Utilizing Alternate Speech/Data or Speech Followed By Data Capabilities .

8、 11 3.4.4 Call Establishment Manual Operation . Utilizing the Unrestricted Digital Capability 11 3.2 3.3 3.4 4 Terminai Adaptation Functions for non transparent services 12 4.1 Data Structure 12 Data Structure on S Interface 12 Data Structure on R Interface 12 Data Structure Provided by the L2R Func

9、tion to the RLP Function 12 4.2 Signalling Mapping 12 4.3 Flow Control . 12 4.3.1 Conditions Requiring Flow Control towards the Network 12 4.3.2 Conditions Requiring Flow Control towards TE2 13 4.3.3 Local Flow Control . 13 4.3.4 Character Orientated Protocol with No Flow Control . 13 Buff ers . 13

10、4.4.1 TX Buff ers . 13 4.4.2 RX Buffers . 13 4.5 Bit Transparency . 14 4.6 Transportation of BREAK condition . 14 4.7 Data Compression 14 4.1.1 4.1.2 4.1.3 4.4 5 Terminal interfacing to GSM 04.08 Mapping 17 5.1 Mobile Originated Calls 17 5.2 Mobile Terminated Calls 18 6 Functionality for the Support

11、 of Dedicated PAD Services 19 Annex A (Normative): UR FUNCTIONALIN . 20 A.l Introduction . 20 A.2 The L2RCOP 20 ETSI GSM*O7-02 96 m 3400855 0309858 T37 m Page 4 GSM 07.02 Version 5.1.0: May 1996 A.3 Use of the L2RCOP . 22 A.3.1 Radio Link Connection Control 22 A.3.2 Data Transfer . 22 A.3.3 Status T

12、ransfer . 22 A.3.4 Flow Control . 22 A.3.5 Break . 22 A.3.5.1 Normal Realization 22 A.3.5.2 Realization in case of Data Compression is used 23 Annex B (Informative): Use of the 9 pin version of V.24 as a MT2 type . 24 History . 25 ETSI GSM*07=02 96 3400855 0109859 973 Page 5 GSM 07.02 Version 5.1.0:

13、 May 1996 Foreword This Global System for Mobile communications Technical Specification (GTS) has been produced by the Special Mobile Group (SMG) Technical Committee (TC) of the European Telecommunications Standards Institute (ETSI). This GTS defines the interfaces and Terminal Adaptation Functions

14、(TAF) integral to a Mobile Termination (MT) which enables the attachment of asynchronous terminals to a MT within the digital cellular telecommunications system (Phase ZPhase 2+). This GTS is a TC-SMG approved GSM technical specification version 5, which contains GSM Phase 2+ enhancements/features t

15、o the version 4 GSM technical specification. The European Telecommunications Standard from which this Phase 2+ GTS has evolved is Phase 2 GSM ETS 300 583 (GSM 07.01 version 4.5.1). GTS are produced by TC-SMG to enable the GSM Phase 2 + specifications to become publicly available, prior to submission

16、 for the formal ETSI standards approval procedure to become European Telecommunications Standards (ETS). This ensures the earliest possible access to GSM Phase 2+ specifications for all Manufacturers, Network operators and implementors of the Global System for Mobile communications. The contents of

17、this GTS are subject to continuing work within TC-SMG and may change following formal TC-SMG approval. Should TC-SMG modify the contents of this GTS it will then be republished by ETSI with an identifying change of release date and an increase in version number as follows: Version 5.x.y where: y the

18、 third digit is incremented when editorial only changes have been incorporated in the specif ication; x the second digit is incremented for all other types of changes, .e. technical enhancements, corrections, updates, etc. NOTE: TC-SMG has produced documents which give the technical specifications f

19、or the implementation of the digital cellular telecommunications system. Historically, these documents have been identified as GSM Technical Specifications (GSM-TSs). These TSs may have subsequently become I-ETSs (Phase l), or ETSs/ETSI Technical Reports (ETRs) (Phase 2). TC-SMG has also produced ET

20、SI GSM TSs which give the technical specifications for the implementation of Phase 2+ enhancements of the digital cellular telecommunications system. These version 5.x.x GSM Technical Specifications may be referred to as GTSs. ETSI GSM*:07-02 96 H 3400855 0309860 b95 Page 6 GSM 07.02 Version 5.1 .O:

21、 May 1996 Blank page ETSI GSM*07-02 96 3400855 Ol1098bL 521 = Page 7 GSM 07.02 Version 5.1.0: May 1996 1 Scope This specification defines the interfaces and Terminal Adaptation Functions (TAF) integral to a Mobile Termination (MT) which enables the attachment of asynchronous terminals to a MT (see G

22、SM 04.02). The general aspects of Terminal Adaptation Functions are contained in GSM 07.01. This specification covers support of these services for the following interfaces and procedures: V.14 procedures V.21 DTEIDCE interface V.22bis DTE/DCE interface V.23 DTWDCE interface V.32 DTE/DCE procedures

23、1.420 S interface V.25bis signalling procedures V.25ter signalling procedures The asynchronous data rates between the MT and the TE2 are defined in GSM 02.02. 1.1 Normative references This GTS incorporates by dated and undated reference, provisions from other publications. These normative references

24、 are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this GTS only when incorporated in it by amendment or revision. For undated references, the latest edition of

25、the publication referred to applies. 131 41 71 GSM O1 .O4 (ETR 100): “Digital cellular telecommunication system (Phase 2); Abbreviations and acronyms“. GSM 02.02 (ETS 300 501): “Digital cellular telecommunication system (Phase2); Bearer Services (6s) supported by a GSM Public Land Mobile Network (PL

26、MN)“. GSM 03.1 O (ETS 300 528): “Digital cellular telecommunication system (Phase 2); GSM Public Land Mobile Network (PLMN) connection types“. GSM 04.02 (ETS 300 551 ): “Digital cellular telecommunication system (Phase 2); GSM Public Land Mobile Network (PLMN) access reference configuration“. GSM 04

27、.08 (ETS 300 557): “Digital cellular telecommunication system (Phase 2); Mobile radio interface layer 3 specification“. GSM 04.21 (ETS 300 562): “Digital cellular telecommunication system (Phase 2); Rate adaption on the Mobile Station - Base Station System (MS - BSS) interface “. GSM 07.01 (ETS 300

28、582): “Digital cellular telecommunication system (Phase 2); General on Terminal Adaptation Functions (TAF) for Mobile Stations (MS) I. GSM 07.07 (ETS 300 462): “Digital cellular telecommunication system (Phase 2); AT command set for GSM Mobile Equipment (ME) GSM 09.05 (ETS 300 602): “Digital cellula

29、r telecommunication system (Phase 2); Interworking between the Public Land Mobile Network (PLMN) and the Packet Switched Public Data Network (PSPDN) for Packet Assembly/Disassembly (PAD) facility access“. ETSI GSM*07.02 96 = 3400855 0309862 Yb8 Page 8 GSM 07.02 Version 5.1.0: May 1996 i 31 i 41 i 51

30、 11 71 i 91 CCITT Recommendation V.4: “General structure of signals of international alphabet No.5 code for character oriented data transmission over public telephone networks“. CCITT Recommendation V.25 bis (1988): Blue book, Volume VIII, Fascicle VIII.l “Automatic Calling and/or Answering Equipmen

31、t on the General Switched Telephone Network (GSTN) using the 1 OO-Series Interchange Circuits“. ITU-T Recommendation V.25ter: “Serial asynchronous automatic dialing and control“. CCIlT Recommendation V.11 O: “Support of data terminal equipments (DTEs) with V-Series interfaces by an integrated servic

32、es digital network“. CCITT Rec. V.24 (1988): Blue book, Volume VIII, Fascicle VIII.l “List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment“. CCITT Rec. V.21 (1988): Blue book, Volume Vlll, Fascicle VIII.l “300 bits per second duple

33、x modem standardized for use in the general switched telephone network“. CCITT Recommendation V.14 (1988): Blue book, Volume VIII, Fascicle VIII.l “Transmission of start-stop characters over synchronous bearer channels“. CCIlT Recommendation V.22bis (1988): Blue book, Volume VIII, Fascicle VIII.l “2

34、400 bits per second duplex modem using the frequency division technique standardized for use on the general“. CCITT Recommendation V.23 (1988): Blue book, Volume VIII, Fascicle VIIi.1 “600/1200-baud modem standardized for use in the general switched telephone network“. CCITT Recommendation V.32 (198

35、8): Blue book, Volume VIII, Fascicle VIII.l “A family of 2-wire, duplex modems operating at data signalling rates of up to 9600 bit/s for use in the general switched telephone network and on leased telephone- type circuits“. CCITT Recommendation V.42 (1 988): Blue book, Volume VIII, Fascicle VIII.l

36、“error-correcting procedures for DCEs using asynchronous-to-synchronous conversion“. ITU-T Recommendation V.42bis: “Data compression procedures for data circuit terminating equipment (DCE) using error correction procedures CCITT Recommendation X.28: “DTEIDCE interface for a start-stop mode data term

37、inal equipment accessing the packet assembly/disassembly facility (PAD) in a public data network situated in the same country“. Recommendations 1.31 0-1.470 (Study Group XVIII): Blue book, Volume I II, Fascicle I I I .8, Overall network aspects and functions, ISDN user-network in terfaces. CCIlT Rec

38、ommendation 1.420: Blue book, Volume III, Fascicle 111.8 “Basic user- network interface“. Personal Computer Memory Card Association: “PCMCIA 2.1 or PC-Card 3.0 electrical specification or later revisions“. IrDA “IrPHY Physical signalling standard“. ETSI GSfl*O7-02 96 3400855 0207863 3T4 Page 9 GSM 0

39、7.02 Version 5.1.0: May 1996 P71 TIA-617: “Data Transmission Systems and Equipment - In-Band DCE Control“. 1.3 Abbreviations Abbreviations used in this specification are listed in GSM 01.04. 2 Reference Configuration GSM 07.01 and GSM 04.02 describe the basic reference configurations. 2.1 Customer A

40、ccess Configuration This configuration is as shown in Figure 1 of GSM 04.02. This specification specifically refers to the Mobile Terminations (MTs) which support terminals of the type TE1 and TE2 with asynchronous capabilities. The TAF is functionally a part of an MT1, MT2 or MTO with an integral a

41、synchronous data capability. 2.2 Terminal Adaptation Function The TAF provides facilities to allow manual or automatic call control functions associated with alternate speechIdata, speech followed by data and circuit switched services. The following functions are also included: Conversion of electri

42、cal, mechanical, functional and procedural characteristics of the V series and ISDN type interfaces to those required by the PLMN Bit rate adaptation of the V series data signalling rates and the ISDN 64 kbit/s to that provided in the PLMN The mapping functions necessary to convert automatic calling

43、 and/or automatic answering procedures of recommendation V.25 bis or V.25 ter and parameters for asynchronous operation The mapping functions necessary to convert S interface signalling to the PLMN Dm channel signalling Flow control (in some cases resulting in non-transparency of data as described i

44、n section 4.3) Layer 2 Relaying (see Annex A) In-call modification function Synchronization procedure, which means the task of synchronizing the entry to and the exit from the data transfer phase between two user terminals. This is described in GSM 07.01 Filtering of channel control information as d

45、escribed in GSM 07.01 Terminal compatibility checking ETSI GSM*07.02 96 3400855 0107864 230 Page 10 GSM 07.02 Version 5.1 .O: May 1996 3 Terminal Adaptation Functions for transparent services GSM 03.10 refers to the connection types supporting the transparent services. 3.1 Rate Adaptation GSM 04.21

46、describes the rate adaptation scheme to be utilized over the Base Station (BS) to Mobile Station (MS) link. GSM 03.10 refers to the rate adaptation elements to be provided in the MS. 3.1.1 Rate Adaptation - V series This is provided as indicated in GSM 04.21 3.1.2 Rate Adaptation - S Interface (1.42

47、0) The ISDN rate adapted frame format is modified to the PLMN rate adapted format as indicated in GSM 04.21. 3.2 Interchange Circuit Signalling Mapping The interchange circuit signalling mapping at the interface between the TE2 and the MT shall conform to CCIlT V.24. The signals required at this int

48、erface are shown in Table 2. GSM 04.21 refers to the frame structure and identifies the use of the status bits for the carriage of signalling information. Status bits (S1 ,S3,S4,S6,S8,S9 and X): The bits S and X are used to convey channel control information associated with the data bits in the data

49、 transfer stage as shown below. The S bits are put into two groups SA and SB to carry the condition of two interchange circuits. The X bit is used to carry the condition of circuit 106. The mechanism for proper assignment of the control information from the transmitting signal rate adapter interface via these bits to the receiving signal rate adapter interface is shown below in table 1. For the S and X bits, a ZERO corresponds with the ON condition, a ONE with the OFF condition. Table 1 : General mapping scheme for V.21, V.22 and V.23 interchange circ