ETSI GSM 07 07-1996 Digital Cellular Telecommunications System (Phase 2+) AT Command Set for GSM Mobile Equipment (ME)《参见ETS 300 642(版本4 1 0)》.pdf

1、ETSI GSMsr07.07 96 = 3400855 0127582 525 GSM ip 1 ECHNICAL n GSM 07.07 July 1996 Version 5.0.0 Source: ETSI TC-SMG Reference: TS/SMG-O40707Q ICs: 33.060.50 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS Dig

2、ital cellular telecommunications system (Phase 2+); AT command set for GSM Mobile Equipment (ME) (GSM 07.07) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - Sophia Antipolis - Valbo

3、nne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretatiatQetsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in al

4、l media. 8 European Telecommunications Standards Institute 1996. All rights reserved. ETSI GSM*O7.07 96 3400b55 0327583 Yb3 Page 2 GSM 07.07 Version 5.0.0: July 1996 Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, m

5、ay occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. Page 3 GSM 07.07 Version 5.0.0: July 1996 Contents Foreword . 5 1 2 3 4 5 6 7 Scope 7 References 7 Abbreviations and definitions 9 3.1 Abbreviati

6、ons . 9 3.2 Definitions 9 AT command syntax . 10 4.1 Command line 10 4.2 Information responses and result codes 11 4.3 ITU-T V.25ter 14 TE-TA interface commands . 11 General commands . 12 5.1 Request manufacturer identification +CGMI 12 5.2 Request model identification +CGMM . 12 5.3 Request revisio

7、n identification +CGMR . 13 5.4 Request product serial number identification +CGSN . 13 5.5 Select TE character set +CSCS 14 5.6 ITU-T V.25ter 141 generic TA control commands . 15 5.7 PCCA STD-1 O1 17 select wireless network +WS46 . 15 5.8 Informative examples . 15 Call control commands and methods

8、17 6.1 Select type of address +CSTA . 17 6.2 ITU-T V.25ter 14 dial command D . 17 6.3 Direct dialling from phonebooks 18 6.4 Call mode +CMOD . 19 6.5 Hangup call +CHUP . 19 6.6 Alternating mode call control method 20 6.7 Select bearer service type +CBST . 22 6.8 Radio link protocol +CRLP . 23 6.9 Se

9、rvice reporting control +CR 23 6.1 O Extended error report +CEER 24 6.1 1 Cellular result codes +CRC . 24 6.12 6.1 3 ITU-T V.25ter 14 data compression commands 26 6.14 Informative examples . 26 ITU-T V.25ter 14 call control commands . 25 Network service related commands 27 7.1 Subscriber number +CNU

10、M . 27 7.2 Network registration +CREG . 28 Operator selection +COPS 29 7.3 7.4 Facility lock +CLCK 30 7.5 Change password +CPWD 31 7.6 Calling line identification presentation +CLIP . 32 7.7 Calling line identification restriction +CLIR . 32 7.8 Connected line identification presentation +COLP 33 7.

11、9 Closed user group +CCUG 34 7.10 Call forwarding number and conditions +CCFC 35 7.1 1 Call waiting +CCWA 36 7.1 2 Call hold and multiparty +CHLD . 37 7.1 3 Call transfer +CTFR . 37 7.1 4 Unstructured supplementary service data +CUSD 38 7.1 5 Advice of Charge +CAOC 39 ETSI GSM%*Q7.07 96 H 3400855 01

12、27585 234 Page 4 GSM 07.07 Version 5.0.0: July 1996 7.1 6 Supplementary service notifications +CSSN . 39 7.17 Informative examples 40 8 Mobile Equipment control and status commands . 42 8.1 Phone activity status +CPAS . 44 8.2 Set phone functionality +CFUN . 44 8.3 Enter PIN +CPIN . 45 8.4 Battery c

13、harge +CBC 46 8.5 Signal quality +CSQ 47 8.6 Mobile Equipment control mode +CMEC 47 8.7 Keypad control +CKPD . 48 8.8 Display control +CDIS . 49 8.9 Indicator control +CIND . 50 8.10 Mobile Equipment event reporting +CMER . 51 8.1 1 Select phonebook memory storage +CPBS 52 8.12 Read phonebook entrie

14、s +CPBR 53 8.13 Find phonebook entries +CPBF 54 8.14 Write phonebook entry +CPBW 55 8.15 Clock +CCLK . 55 8.16 Alarm +CALA 56 8.17 Generic SIM access +CSIM 57 8.1 8 Informative examples 57 9 Mobile Equipment errors . 61 9.1 9.2 Mobile Equipment error result code +CME ERROR . 62 9.3 Informative examp

15、les 62 Report Mobile Equipment error +CMEE 61 Annex A (normative): Summary of commands from other standards 63 Annex B (normative): Summary of result codes . 65 Annex C (informative): Commands from TIA IS-101 66 C.l Introduction . 66 C.2 Commands . 67 Select mode +FCLASS . 67 Buffer threshold settin

16、g +VBT . 67 Calling number ID presentation +VCID . 68 Receive gain selection +VGR . 68 Transmit gain selection +VGT . 68 Initialise voice parameters +VIP 68 Inactivity timer +VIT . 69 Line selection +VLS . 69 Receive data state +VRX 71 Select compression method +VSM . 71 DTMF and tone generation +vT

17、S . 71 Tone duration +VTD 72 Transmit data state +VTX . 72 C.2.1 C.2.2 C.2.3 C.2.4 C.2.5 C.2.6 C.2.7 C.2.8 C.2.9 C.2.10 C.2.11 C.2.12 C.2.13 Annex D (informative): Bibliography . 73 Annex E (informative): Mobile originated alternating voice/data call example . 74 Annex F (informative): Mobile termin

18、ated voice followed by data call example . 75 Annex G (informative): Voice call example . 76 History . 77 Page 5 GSM 07.07 Version 5.0.0: July 1996 Foreword This Global System for Mobile communications Technical Specification (GTS) has been produced by the Special Mobile Group (SMG) Technical Commit

19、tee (TC) of the European Telecommunications Standards Institute (ETSI). This GTS specifies the AT command for terminal equipments being used within the digital cellular telecommunications system (Phase 2/Phase 2+). This GTS is a TC-SMG approved GSM technical specification version 5, which contains G

20、SM Phase 2+ enhancementsAeatures to the version 4 GSM technical specification. The ETS from which this Phase 2+ GTS has evolved is Phase 2 GSM prETS 300 642 (GSM 07.07 version 4.1 .O). GTS are produced by TC-SMG to enable the GSM Phase 2 + specifications to become publicly available, prior to submis

21、sion for the formal ETSI standards approval procedure to become European Telecommunications Standards (ETC). This ensures the earliest possible access to GSM Phase 2+ specifications for all Manufacturers, Network operators and implementors of the Global System for Mobile communications. The contents

22、 of this GTS are subject to continuing work within TC-SMG and may change following formal TC-SMG approval. Should TC-SMG modify the contents of this GTS it will then be republished by ETSI with an identifying change of release date and an increase in version number as follows: Version 5.x.y where: y

23、 the third digit is incremented when editorial only changes have been incorporated in the specification; x the second digit is incremented for all other types of changes, .e. technical enhancements, corrections, updates, etc. NOTE: TC-SMG has produced documents which give the technical specification

24、s for the implementation of the digital cellular telecommunications system. Historically, these documents have been identified as GSM Technical Specifications (GSM-TSs). These TSs may have subsequently become I-ETSs (Phase l), or ETSs/ETSI Technical Reports (ETRs) (Phase 2). TC-SMG has also produced

25、 ETSI GSM TSs which give the technical specifications for the implementation of Phase 2+ enhancements of the digital cellular telecommunications system. These version 5.x.x GSM Technical Specifications may be referred to as GTSs. ETSI GSM*07*07 96 M 3400855 0127587 O07 M Page 6 GSM 07.07 Version 5.0

26、.0: July 1996 Blank page - - ETSI GSM*O7-07 b = 3400855 0127588 T43 m TA ME control Page 7 GSM 07.07 Version 5.0.0: July 1996 ME 1 Scope This European Telecommunications Standard (ETS) specifies a profile of AT commands and recommends that this profile be used for controlling Mobile Equipment (ME) f

27、unctions and GSM network services from a Terminal Equipment (TE) through Terminal Adaptor (TA). The command prefix +c is reserved for Digital Cellular in ITU-T Recommendation V.25ter 14. This ETC has also the syntax details used to construct these extended GSM commands. Commands from ITU-T Recommend

28、ation V.25ter 14 and existing digital cellular standards (TIA IS-99 15 and TIA IS-135 16) are used whenever applicable. Some of the new commands are defined such way that they can be easily applied to ME of networks other than GSM. ITU-T T.31 ll and T.32 12 fax AT commands may be used for GSM fax tr

29、ansmission from TE. GSM Short Message Service AT commands are defined in GSM 07.05 24. This ETS assumes an abstract architecture comprising a TE (e.g. a computer) and a ME interfaced by a TA (see figure 1). The span of control of the defined commands should allow to handle any physical implementatio

30、n that this abstract architecture may lead to: - - - - TA, ME and TE as three separate entities; TA integrated under the ME cover, and the TE implemented as a separate entity; TA integrated under the TE cover, and the ME implemented as a separate entity; TA and ME integrated under the TE cover as a

31、single entity. The commands described in this ETS may be observed on the link between the TE and the TA. However, most of the commands retrieve information about the ME, not about the TA. responses ME status network messages .L USER Bearer Services (6s) supported by a GSM Public Land Mobile Network

32、(PLMN)“. GSM 02.03 (ETS 300 502): “Digital cellular telecommunication system (Phase 2); Teleservices supported by a GSM Public Land Mobile Network (PLMN)“. GSM 02.81 (ETC 300 514): “Digital cellular telecommunication system (Phase 2); Line identification supplementary services - Stage 1 “. ETSI GSPl

33、*O7-07 76 3400855 0127589 98T Page 8 GSM 07.07 Version 5.0.0: July 1996 41 GSM 02.82 (ETS 300 51 5): “Digital cellular telecommunication system (Phase 2); Call Forwarding (CF) supplementary services - Stage 1“. 151 GSM 02.83 (ETC 300 516): “Digital cellular telecommunication system (Phase 2); Call W

34、aiting (CW) and Call Hold (HOLD) supplementary services - Stage 1“. GSM 02.88 (ETS 300 520): “Digital cellular telecommunication system (Phase 2); Call Barring (CB) supplementary services - Stage 1“. GSM 03.03 (ETS 300 523): “Digital cellular telecommunication system (Phase 2); Numbering, addressing

35、 and identification“. GSM 04.08 (ETS 300 557): “Digital cellular telecommunication system (Phase 2); Mobile radio interface layer 3 specification“. 191 GSM MOU SE.13, GSM MOU Permanent Reference Document SE.13 (October 1994): “GSM Mobile Network Codes and Names“. 1101 ITU-T Recommendation E.212: “Id

36、entification plan for land mobile stations“. ITU-T Recommendation T.31: “Asynchronous facsimile DCE control, service class 7“. ITU-T Recommendation T.32: “Asynchronous facsimile DCE control, service class 2“. 11 31 ITU-T Recommendation T.50: “International Reference Alphabet (IRA) (Formerly Internat

37、ional Alphabet No. 5 or IA5) - information technology - 7-bit coded character set for information exchange“. ITU-T Draft new Recommendation V.25ter: “Serial asynchronous automatic dialling and control“. i 51 Telecommunications Industry Association TIA IS-99: “Data Services Option Standard for Wideba

38、nd Spread Spectrum Digital Cellular System“. Telecommunications Industry Association TIA IS-135: “800 MHz Cellular Systems, TDMA Services, Async Data and Fax“. i 71 Portable Computer and Communications Association PCCA STD-1 O1 Data Transmission Systems and Equipment: “Serial Asynchronous Automatic

39、Dialling and Control for Character Mode DCE on Wireless Data Services“ GSM 04.22 (ETS 300 563): “Digital cellular telecommunication system (Phase 2); Radio Link Protocol (RLP) for data and telematic services on the Mobile Station - Base Station System (MS - BSS) interface and the Base Station System

40、 - Mobile-services Switching Centre (BSS - MSC) interface“. i 91 GSM 02.30 (ETS 300 51 1): “Digital cellular telecommunication system (Phase 2); Man Machine Interface (MMI) of the Mobile Station (MS)“. GSM 05.08 (ETS 300 578): “Digital cellular telecommunication system (Phase 2); Radiosubsystem link

41、 control“. GSM 02.85 (ETS 300 51 8): “Digital cellular telecommunication system (Phase 2); Closed User Group (CUG) supplementary services - Stage 1“. GSM 02.84 (ETS 300 51 7): “Digital cellular telecommunication system (Phase 2); MultiParty (MPTY) supplementary services - Stage 1“. - ETSI GSSa*:07.0

42、7 %b W 3LI00855 0327590 6T3 W Page 9 GSM 07.07 Version 5.0.0: July 1996 GSM 02.90 (ETS 300 625): “Digital cellular telecommunication system (Phase 2); Stage 1 description of Unstructured Supplementary Service Data (USSD)“. GSM 07.05 (ETS 300 585): “Digital cellular telecommunication system (Phase2);

43、 Use of Data Terminal Equipment - Data Circuit terminating Equipment (DTE - DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS)“. GSM 03.38 (ETS 300 628): “Digital cellular telecommunication system (Phase 2); Alphabet and language specific information“. GSM 02.24 (ETS 300

44、 510): “Digital cellular telecommunication system (Phase 2); Description of Charge Advice Information (CAI)“. GSM 02.86 (ETS 300 51 9): “Digital cellular telecommunication system (Phase 2); Advice of Charge (AOC) supplementary services - Stage 1“. Abbreviations and definitions Abbreviations For the

45、purposes of this ETS the following abbreviations apply: AT BCD ETSI IMEI I RA IrDA IS0 ITU-T ME MOU PCCA RLP SIM TA TE TIA ATtention; this twocharacter abbreviation is always used to start a command line to be sent from TE to TA Binary Coded Decimal European Telecommunications Standards Institute In

46、temational Mobile station Equipment Identity International Reference Alphabet (ITU-T T.50 13) Infrared Data Association Intemational Standards Organisation Intemational Telecommunication Union - Telecommunications Standardization Sector Mobile Equipment, e.g. a GSM phone (equal to MS; Mobile Station

47、) Memorandum of Understanding (GSM operator joint) Portable Computer and Communications Association Radio Link Protocol Subscriber Identity Module Terminal Adaptor, e.g. a GSM data card (equal to DCE; Data Circuit terminating Equipment) Terminal Equipment, e.g. a computer (equal to DTE; Data Termina

48、l Equipment) Telecommunications Industry Association 3.2 Definitions For the purposes of this ETS the following syntactical definitions apply (refer also clause 4): Carriage return character, which value is specified with command 53, Linefeed character, which value is specified with command s4. C. N

49、ame enclosed in angle brackets is a syntactical element. Brackets themselves do not appear in the command line. Optional subparameter of a command or an optional patt of TA information response is enclosed in square brackets. Brackets themselves do not appear in the command line. When subparameter is not given in parameter type commands, new value equals to its previous value. In action type commands, action should be done on the basis of the recommended default setting of the su bparameter. ETSI GSfl*Q7-07 9b E 3400855 OI12759L 5