ETSI PRETS 300 386-2-2-1996 Equipment Engineering (EE) Public Telecommunication Network Equipment Electromagnetic Compatibility (EMC) Requirements Part 2 Product Specific Complianc.pdf

1、ETSI PRETS*3OO 38h-2-2 96 H 3400855 0334575 511 m I - EUROPEAN 1 ELECOMMUNICATION STANDARD DRAFT pr ETS 300 386-2-2 September 1996 Source: ETSI TC-EE Reference: DE/EE 04003-2-2 ICs: 33.020 Key words: EMC, network, transmission Equipment Engineering (EE); Public telecommunication network equipment El

2、ectromagnetic Compatibility (EMC) requirements; Part 2: Product specific compliance criteria and operating conditions; Subpart 2: Transmission equipment ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 R

3、oute des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat Qetsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foreg

4、oing restriction extend to reproduction in all media. 8 European Telecommunications Standards Institute 1996. All rights resewed. ETSI PRETSU300 386-2-2 Yb 3400855 0134576 458 Page 2 Draft prETS 300 386-2-2: September 1996 Whilst every care has been taken in the preparation and publication of this d

5、ocument, errors in content, typographical or othetwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. . ETSI PRETS*3OO 386-2-2 96 m 3400855 0134577 394 Page 3 Draft prETS 300 386-2-2: Septem

6、ber 1996 Contents Foreword . 5 Scope 7 Normative References 7 Definitions and abbreviations 9 3.1 Definitions 9 3.2 Abbreviations . io Priority of service . 10 Installation environment 10 Test methods and limits 10 6.1 Telecommunication Centres 11 6.1 . 1 Enclosure port . 11 6.1.2 Poits for outdoor

7、signal lines . 12 6.1.3 Ports for indoor signal lines . 13 6.1.4 AC power ports 14 6.1.5 DC power ports . 15 Other than telecommunication centres 16 6.2.1 Enclosure port . 16 6.2.2 Ports for outdoor signal lines . 17 6.2.3 Ports for indoor signal lines 18 6.2.4 AC power ports 19 6.2.5 DC power ports

8、 . 20 6.2 Test configuration 21 Operational conditions during testing 22 8.1 Emission . 22 8.2 Immunity 22 Immunity and resistibility performance criteria 23 9.1 General performance criteria . 23 9.1.1 Digital signal ports . 23 9.1.1.1 Performance criteria A (continuous phenomena) 23 9.1.1.2 Perform

9、ance criteria B (transient phenomena) . 23 9.1.1.3 9.1.2.1 Performance criterion A (continuous phenomena) 23 9.1.2.2 Performance criterion B (transient phenomena) . 23 9.1.2.3 SDH and PDH interfaces . 24 9.2.1.1 Tributary interfaces 24 9.2.1.2 Aggregate interfaces . 24 9.2.2 ISDN interfaces . 24 9.2

10、.2.1 Primary rate access ISDN interface 24 9.2.2.2 Network termination NT1 for ISDN “U“ interface . 24 9.2.2.3 Network termination NT1 for ISDN “STT“ interface 24 9.2.3 Analogue interfaces . 24 9.2.3.1 Trunk interfaces . 24 9.2.3.2 Subscriber interfaces . 24 V.l O, V.11, V.24, V.28, V.35, V.36 and s

11、imilar V.series interfaces 24 Performance criteria R (resistibility) . 23 Analogue voice frequency signal ports 23 Performance criterion R (resistibility) . 24 Specific performance criteria . 24 9.1.2 9.2 9.2.1 9.2.4 ETSI PRETS*300 386-2-2 9b 3400855 0334578 220 m Page 4 Draft prETS 300 386-2-2: Sep

12、tember 1996 9.2.5 Ethernet and packet-data interfaces . 24 9.2.5.1 Performance criteria A (continuous phenomena) . 25 9.2.5.2 Performance criteria B (transient phenomena) . 25 9.2.6 Service and maintenance interfaces 25 9.2.7 Synchronization interfaces 25 9.2.7.1 Performance criteria A (continuous p

13、henomena) . 25 9.2.7.2 Performance criteria B (transient phenomena) . 25 Remote alarm interfaces 25 9.2.8.1 performance criteria A (continuous phenomena) . 25 9.2.8.2 Performance critena B (transient phenomena) . 25 9.2.8.3 Performance criteria R (resistibility) 25 9.2.8 Annex A (Normative): Correla

14、tion between essential requirements and the provisions of the present ETS 26 History . 27 ETSI PRETSa300 386-2-2 96 3400855 0134579 Lb7 Page 5 Draft prETS 300 386-2-2: September 1996 Foreword This draft European. Telecommunications Standard (ETS) has been prepared by the Equipment Engineering (EE) T

15、echnical Committee of the European Telecommunications Standard Institute (ETSI), and is now submitted for the Public Enquiry phase of the ETSI standards approval procedure. The present ETS constitutes a subpart of a multi-part ETS as shown below: ETS 300 386 Equipment Engineering (EE); Public teleco

16、mmunication network equipment Electromagnetic Compatibility (EMC) requirements Part 1: Part 2: Product family overview, compliance criteria and test levels Product specific compliance criteria and operating conditions Subpart 1: Switching equipment Subpart 2: Transmission equipment Subpart 3: Power

17、supply equipment Subpart 4: Supervisory equipment This ETS has been prepared in response to European Commission mandate BC-T-353 and, upon citation in the Official Journal of the European Communities, is intended to become a Harmonized Standard within the terms of the New Approach. Conformity to thi

18、s Harmonized Standard will confer presumption of compliance with the essential requirements of the EMC Directive 27. Proposed transposition dates Date of latest announcement of this ETS (doa): 3 months after ETSI publication Date of latest publication of new National Standard or endorsement of this

19、ETS (dople): 6 months after doa Date of withdrawal of any conflicting National Standard (dow): 4 years after doa Secretariat note: Certain technical comments were received too late to be taken into consideration by the Technical Committee when deciding to approve the present draft for Public Enquiry

20、. In order not to delay the progress of this ETS, these comments are given in footnotes in appropriate places in the text. These comments will be addressed during the TC review following the Public Enquiry. ETSI PRETS*300 386-2-2 Yb W 3400855 0134580 789 = Page 6 Draft prETS 300 386-2-2: September 1

21、996 Blank page ETSI PRETSx300 386-2-2 96 3400855 OL3458L 815 M Page 7 Draft prETS 300 386-2-2: September 1996 1 Scope This European Telecommunications Standard (ETC) defines the product specific performance criteria and operating conditions for non-radio transmission equipment and ancillary equipmen

22、t intended to be used within a public telecommunication network. Such equipment includes: - multiplexers; - line equipment and repeaters, e.g. equipment for: - Synchronous Digital Hierarchy (SDH); - - Asynchronous Transfer Mode (ATM); Digital Cross Connect Systems (DCC); network terminations. This E

23、TS specifies the operating conditions and the minimum compliance criteria for such equipment. The applicable EMC tests, the method of measurements and the limits are specified in ETS 300 386-1 I, from which the EMC requirements are selected taking into account the priority of service provided by the

24、 equipment under consideration. The environmental classification used in this ETS refers to ETS 300 386-1 l. The requirements of this ETS do not cover those cases where a potential source of interference which produces individually repeated transient phenomena or continuous phenomena is permanently

25、present, e.g., a radar or broadcast site in the near vicinity. In such cases it may be necessary to use special protection applied to either the source of interference or the equipment interfered with, or both. Equipment for cabled distribution systems for television and sound signals as defined in

26、EN50083-2 26 is outside the scope of this ETS. 2 Normative References This ETS incorporates by dated and undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references,

27、subsequent amendments to or revisions of any of these publications apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. ETS 300 386-1 (1 994): “Equipment Engineering (EE); Public telecommunication n

28、etwork equipment Electro-Magnetic Compatibility (EMC) requirements; Part 1 : Product family overview, compliance criteria and test levels“. EN 61 000-4-2: “Electromagnetic Compatibility (EMC); Part 4: Testing and Measurement Techniques ; Section 2: Electrostatic discharge immunity test Basic EMC pub

29、lication“ ENV 501 40: “Electromagnetic Compatibility; Basic immunity standard; Radiated radio-frequency electromagnetic field; Immunity test“. EN 61000-4-4: “Electromagnetic Compatibility (EMC) ; Part 4: Testing and Measurement Techniques; Section 4: Electrical fast transienffburst immunity test ; B

30、asic EMC publication“. EN 61 000-4-5: “Electromagnetic Compatibility (EMC); Part 4: Testing and Measurement Techniques; Section 5: Surge immunity test“. ENV 501 41 : “Electromagnetic compatibility; Basic immunity standard; Conducted disturbances induced by radio-frequency fields; Immunity test“. IEC

31、 1000-4-1 1: “Electromagnetic Compatibility (EMC) ; Part 4: Testing and Measuring Techniques; Section 11 : Voltage dips, short interruptions and voltage variations: Immunity tests“. Page 8 ETSI PRETS*300 38b-2-2 96 3400855 0334582 751 Drift prETS 300 386-2-2: September 1996 ITU-T Recommendation O. 1

32、50: “Digital test patterns for performance measurements on digital transmission equipment“. ETC 300 166: “Transmission and Multiplexing (TM); Physical and electrical characteristics of hierarchical digital interfaces for equipment using the 2048 kbitls-based plesiochronous or synchronous digital hie

33、rarchies“. ETC 300 232: I Transmission and Multiplexing (TM); Optical interfaces for equipments and systems relating to the Synchronous Digital Hierarchy I. ITU-T Recommendation G.958: “Digital line systems based on the synchronous digital hierarchy for use on optical fibre cables“. ETC 300 O1 1 : “

34、Integrated Services Digital Network (ISDN); Primary rate user- network interface; Layer 1 specification and test principles“. ITU-T Recommendation G.961: “Digital transmission system on metallic local lines for ISDN Basic Rate Access“. ETS 300 012: “Integrated Services Digital Network (ISDN); Basic

35、user-network interface; Layer 1 specification and test principles“. ITU-T Recommendation G.712: “Transmission performance characteristics of pulse code modulation“. ITU-T Recommendation (2.552: “Transmission characteristics at 2-wire analogue interfaces of digital exchanges“. ITU-T Recommendation V.

36、l O: “Electrical characteristics for unbalanced double- current interchange circuits operating at data signalling rates up to 1 O0 kbiUs“. ITU-T Recommendation V.11: “Electrical characteristics for balanced double- current interchange circuits operating at data signalling rates up to 1 O Mbitis“. IT

37、U-T Recommendation V.24: “List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DC E)“. ITU-T Recommendation V.28: “Electrical Characteristics for unbalanced double- current interchange circuits“. ITU-T Recommendation V.35: “Data t

38、ransmission at 48 kilobits per second using 60-1 08 kHz group band circuits“. ITU-T Recommendation V.36: “Modems for synchronous data transmission using 60 - 108 kHz group band circuits“. ISO/IEC 8802-3 1993: “Information Technology ; Local and metropolitan area networks; Part 3: Carrier sense multi

39、ple access with collision detection (CSMNCD) access method and physical layer specifications“. ITU-T Recommendation X.25: “Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for terminals operating in the packet mode and connected to public data networks by

40、dedicated circuit“. ITU-T Recommendation G.812: “Timing requirements at the outputs of slave clocks suitable for plesiochronous operation of international digital links“. EN50083-2: “Cabled distribution systems for television and sound signals; Part 2: Electromagnetic compatibility for equipment“. E

41、TSI PRETS8300 386-2-2 96 = 3YOO55 0334583 698 Page 9 Draft prETS 300 386-2-2: September 1996 89/336/EEC “Council Directive of 3 May 1989 on the approximation of laws of the Member States relating to Electromagnetic Compatibility“ (Official Journal L139 of 23/5/89) as modified by 92/31 /EEC. 3 Defini

42、tions and abbreviations 3.1 Definitions For the purposes of this ETS, the definitions of ETS 300 386-1 l subclause 3.1 and the following definitions apply: connection: A temporary association of transmission channels or telecommunication circuits, switching or other functional units set up to provid

43、e for the transfer of information between two or more points in a telecommunication network (IEC 50, chapter 71 4-01 -09). enclosure pork lhe physical boundary of the EUT through which electromagnetic fields may emanate or on which they may impinge. port: A particular interface of the EUT with the e

44、xternal electromagnetic environment. performance criteria A: In relation to immunity testing involving continuous phenomena, operation of the EUT during or following exposure to interfering electromagnetic phenomena such that: - During application of the phenomena: lhe EUT operates as intended witho

45、ut degradation of Performance below the minimum level defined in the relevant subclause of the present ETS, and without loss of function. The EUT operates as intended without degradation of performance below the level specified by the supplier for the use of the apparatus as intended. - After remova

46、l of the phenomena: performance criteria B: In relation to immunity testing involving transient phenomena, operation of the EUT during or following exposure to interfering electromagnetic phenomena such that: - During application of the phenomena: The EUT operates, but degradation of performance bel

47、ow the minimum level defined in the relevant subclause of the present ETS or loss of function may occur. The EUT recovers automatically from any degradation of performance or loss of function which occurred during application of the phenomena, and thereafter the EUT operates as intended without degr

48、adation of performance below the level specified by the supplier for the use of the apparatus as intended. - After removal of the phenomena: performance criteria R: In relation to resistibility testing, operation of the EUT following exposure to interfering electromagnetic phenomena such that: - Afe

49、r removal of the phenomena: The EUT has withstood the application of the phenomena, and subsequently operates as intended without degradation of performance below the level specified by the supplier for the use of the apparatus as intended. The application of the phenomena may cause operation of fuses or other protection devices which require manual replacement or resetting before normal operation is restored. public telecommunication network: A network which provides public access for telecommunications. Terminal equipment is excluded. resistibility: The ability