ETSI PRETS 300 386-2-3-1996 Equipment Engineering (EE) Public Telecommunication Network Equipment Electromagnetic Compatibility (EMC) Requirements Part 2 Product Specific Complianc_1.pdf

1、ETSI PRETS*300 386-2-3 96 3400855 CIL34604 142 EUROPEAN T 1 ELECOMMUNICATION STANDARD DRAW pr ETS 300 386-2-3 September 1996 Source: ETSI TC-EE Reference: DHEE-04003-2-3 ICs: 33.020 Key words: EMC, network, power supply Equipment Engineering (EE); Public telecommunication network equipment Electroma

2、gnetic Compatibility (EMC) requirements; Part 2: Product specific compliance criteria and operating conditions; Subpart 3: Power supply equipment ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route de

3、s Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariatetsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing rest

4、riction extend to reproduction in all media. Q European Telecommunications Standards Institute 1996. All rights reserved. Pane 2 ETSI PRETS*300 386-2-3 96 = 3400855 OL34b05 O9 Draft prETS 300 386-2-3: September 1996 Whilst every care has been taken in the preparation and publication of this document

5、, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. ETSI PRETS*300 386-2-3 96 3400855 OL34bOb TL5 Page 3 Draft prETS 300 386-2-3: September 1996 Co

6、ntents Foreword . 5 1 Scope 7 2 Normative references 7 3 Definitions and abbreviations 8 3.1 Definitions 8 3.2 Abbreviations . 10 4 Priority of service . 10 5 Installation environment 10 6 Test methods and limits 10 6.1 Telecommunication centre environment 12 6.1.1 Enclosure port . 12 6.1.2 Ports fo

7、r outdoor signal lines . 13 6.1.3 Ports for indoor signal lines . 14 6.1.4 AC power ports 15 6.1.5 DC power ports . 16 Environments other than telecommunication centres 17 6.2.1 Enclosure port . 17 6.2.2 Ports for outdoor signal lines . 18 6.2.3 Ports for indoor signal lines . 19 6.2.4 AC power port

8、s 20 6.2.5 DC power ports . 21 6.2 7 Test configuration 22 8 Operational conditions during testing 23 8.1 Emission 23 8.2 Immunity 23 9 Immunity and resistibility performance criteria 23 9.1 General performance criteria . 23 9.1.1 Performance assessment . 23 9.2 AC secondary interface 24 9.2.1 Perfo

9、rmance criteria A (continuous phenomena) 24 9.2.2 Performance criteria B (transient phenomena) . 24 9.2.3 Performance criteria R 24 DC secondary interface . 24 9.3.1 Performance criteria A 24 9.3.2 Performance criteria B 25 9.3.3 Performance criteria R 25 9.4 Control/signal interface 25 9.5 Tertiary

10、 supply interface . 25 9.3 Annex A (Normative): Correlation between essential requirements and the provisions of the present ETS . 26 History 27 ETSI PRETS*3OO 386-2-3 96 = 3400855 0334607 951 u Page 4 Draft prETS 300 386-2-3: September 1996 Blank page Page 5 Draft prETS 300 386-2-3: September 1996

11、ETSI PRETS*300 386-2-3 Yb 3400855 OL34bO8 878 Foreword This draft European Telecommunications Standard (ETS) has been produced by the Equipment Engineering (EE) Technical Committee of the European Telecommunications Standard Institute (ETSI), and is now submitted for the Public Enquiry phase of the

12、ETSI standards approval procedure. The present ETS constitutes a subpart of a multi-part ETS as shown below: ETS 300 386 Equipment Engineering (EE); Public telecommunication network equipment Electromagnetic Compatibility (EMC) requirements Part 1: Part 2: Product family overview, compliance criteri

13、a and test levels Product specific compliance criteria and operating conditions Subpart 1: Switching equipment Subpart 2: Transmission equipment Subpart 3: Power supply equipment Subpart 4: Supervisory equipment This ETS has been prepared in response to European Commission mandate BC-T-353 and, upon

14、 citation in the Official Journal of the European Communities, is intended to become a Harmonized Standard within the terms of the New Approach. Conformity to this Harmonized Standard will confer presumption of compliance with the essential requirements of the EMC Directive 19. Proposed transpositio

15、n dates Date of latest announcement of this ETS (doa): 3 months ater ETSI publication Date of latest publication of new National Standard or endorsement of this ETS (dop/e): 6 months after doa I Date of withdrawal of any conflicting National Standard (dow): 4 years ater doa I Secretariat note: Certa

16、in technical comments were received too late to be taken into consideration by the Technical Committee when deciding to approve the present draft for Public Enquiry. In order not to delay the progress of this ETS, these comments are given in footnotes in appropriate places in the text. These comment

17、s will be addressed during the TC review following the Public Enquiry. ETSI PRETS*300 38b-2-3 7b m 3400855 0134609 724 m Page 6 Draft prETS 300 386-2-3: September 1996 Blank page ETSI PRETS*300 386-2-3 96 m 3400855 OL346LO 446 m Paae 7 Draft prETS 300 386-2-3: September i996 1 Scope This European Te

18、lecommunications Standard (ETS) defines the product-specific specific performance criteria and operating conditions for power supply equipment intended to be used within a public telecommunication network. Such equipment includes: - central power plant; - end of suite power supplies: - uninterruptib

19、le power supply (UPS); - stabilized AC power supply; - and other dedicated telecommunication network power supplies. This ETS specifies the operating conditions and the minimum compliance criteria for such equipment. The applicable EMC tests, the method of measurements and the limits are specified i

20、n ETS 300 386-1 l, from which the EMC requirements are selected taking into account the priority of service provided by the equipment under consideration. The environmental classification used in this ETC refers to ETS 300 386-1 I. The requirements of this ETS do not cover those cases where a potent

21、ial source of interference which produces individually repeated transient phenomena or continuous phenomena is permanently present, e.g., a radar or broadcast site in the near vicinity. In such cases it may be necessary to use special protection applied to either the source of interference or the eq

22、uipment interfered with, or both. Power supply equipment which is uniquely associated with or integrated in other equipment is outside the scope of this ETS. Equipment for cabled distribution systems for television and sound signals as defined in EN50083-2 26 is outside the scope of this ETS. 2 Norm

23、ative references This ETS incorporates by dated and undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these

24、 publications apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies 11 1 ETS 300 386-1 (1994): “Equipment Engineering (EE); Public telecommunication network equipment Electro-Magnetic Compatibility (E

25、MC) requirements Part 1 : Product family overview, compliance criteria and test levels“. IEC 1000-4-1 1 : “Electromagnetic Compatibility (EMC) Part 4: Testing and Measuring Techniques Section 11: Voltage dips, short interruptions and voltage variations Immunity tests“. ETS 300 132-1 : “Equipment Eng

26、ineering (EE); Power supply interface at the input to telecommunications equipment Part 1 : Operated by alternating current (ac)“. ETS 300 132-2: “Equipment Engineering (EE); Power supply interface at the input to telecommunications equipment Part 2: Operated by alternating current (dc)“. CCITT (ITU

27、-T) Recommendation 0.41 : “Psophometer for Use on Telephone-Type Circuits“. IEC 38: “IEC standard voltages“. ETSI PRETSw300 386-2-3 96 3400855 0134611 382 Page 8 Draft prETS 300 386-2-3: September 1996 171 Pl 191 1111 11 21 11 71 3 3.1 IEC 686: “Stabilised power supplies - AC output“ EN 61 000-4-2:

28、“Electromagnetic Compatibility (EMC) Part 4: Testing and Measurement Techniques Section 2: Electrostatic discharge immunity test Basic EMC publication“. ENV 501 40: “Electromagnetic Compatibility Basic immunity standard Radiated radio-frequency electromagnetic field Immunity test“. EN 61 000-4-4: “E

29、lectromagnetic Compatibility (EMC) Part 4: Testing and Measurement Techniques Section 4: Electrical fast transientlburst immunity test Basic EMC publication“. EN 61 000-4-5: “Electromagnetic Compatibility (EMC) Part 4: Testing and Measurement Techniques Section 5: Surge immunity test“. ENV 501 41 :

30、“Electromagnetic compatibility Basic immunity standard Conducted disturbances induced by radio-frequency fields Immunity test“. EN 55022: “Limits and methods of measurement of radio disturbance characteristics of information technology equipment“. ETS 300 127 “Equipment Engineering (EE): Radiated em

31、ission testing of physically large telecommunication systems“. CCITT (ITU-T) Recommendation K.20: “Resistibility of telecommunication switching equipment to overvoltages and overcurrents“. EN 61000-3-2: “Electromagnetic Compatibility (EMC) Part 3: Limits Section 2: Limits for harmonic current emissi

32、ons (equipment input current less than or equal to 16 A per phase)“. EN 61000-3-3 : “Electromagnetic Compatibility (EMC) Part 3: Limits Section 3: Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current less than or equal to 16 A“. EN50083-2: “Ca

33、bled distribution systems for television and sound signals Part 2: Electromagnetic compatibility for equipment“. 89/336/EEC “Council Directive of 3 May 1989 on the approximation of laws of the Member States relating to Electromagnetic Compatibility“ (Official Journal L139 of 23/5/89) as modified by

34、92/31/EEC. Definitions and abbreviations Definitions For the purposes of this ETS, the definitions of ETS 300 386-1 l subclause 3.1 apply in addition to the following: public telecommunication network: A network which provides public access for telecommunications. Terminal equipment is excluded. ETS

35、I PRETS*300 386-2-3 96 3400855 0134612 217 m Page 9 Draft prETS 300 386-2-3: September 1996 power supply: A power source (within the scope of the present ETS) to which telecommunications equipment is intended to be connected. interface “A“: The terminals at which the power supply is connected to the

36、 telecommunications equipment. primary supply: The public mains or a locally generated AC or DC supply. secondary supply: The supply to the telecommunications equipment (e.9. racks or system blocks), derived from the primary supply. AC secondary interface: The output pori of a AC power supply. DC se

37、condary interface: The output port of a DC power supply. AC secondary voltage: The output of the AC power supply at the AC secondary interface. The AC secondary voltage may be either: - - a stabilized AC supply derived from a DC primary supply (e.g. where the power supply is an inverter); or derived

38、 from the AC primary supply (e.g. a stabilized power supply used where the quality of the primary supply is not sufficient to feed telecommunication equipment. DC secondary voltage: The output of the DC power supply at the DC secondary interface. The DC secondary voltage may be derived from the AC p

39、rimary supply with or without a buffer battery. system block: A functional group of equipment depending for its operation and performance upon the secondary power supply. nominal voltage: The nominal value of voltage that designates the type of supply. normal service: The service mode where telecomm

40、unications equipment operates within its specif ication. tertiary supply: A supply to the telecommunications equipment derived from the secondary supply. port: A particular interface of the EUT with the external electromagnetic environment. enclosure port: The physical boundary of the EUT through wh

41、ich electromagnetic fields may emanate or on which they may impinge. performance criteria A: In relation to immunity testing involving continuous phenomena, operation of the EUT during or following exposure to interfering electromagnetic phenomena such that: - During application of the phenomena: Th

42、e EUT operates as intended without degradation of performance below the minimum level defined in the relevant subclause of the present ETS, and without loss of function. The EUT operates as intended without degradation of performance below the level specified by the supplier for the use of the appar

43、atus as intended. - After removal of the phenomena: performance criteria B: In relation to immunity testing involving transient phenomena, operation of the EUT during or following exposure to interfering eiectromagnetic phenomena such that: - During application of the phenomena: The EUT operates, bu

44、t degradation of performance below the minimum levei defined in the relevant subclause of the present ETS or loss of function may occur. The EUT recovers automatically from any degradation of performance or loss of function which occurred during application of the phenomena, and thereafter the EUT o

45、perates as intended without degradation of performance below the level specified by the supplier for the use of the apparatus as intended. - After removal of the phenomena: ETSI PRETS*300 386-2-3 96 3400855 0134613 155 Page 10 Draft prETS 300 386-2-3: September 1996 performance criteria R: In relati

46、on to resistibility testing, operation of the EUT following exposure to interfering electromagnetic phenomena such that: - After removal of the phenomena: The EUT has withstood the application of the phenomena, and subsequently operates as intended without degradation of petformance below the level

47、specified by the supplier for the use of the apparatus as intended. The application of the phenomena may cause operation of fuses or other protection devices which require manual replacement or resetting before normal operation is restored. resistibility: The ability of telecommunication equipment o

48、r a network to withstand the effects of certain physical phenomena up to a certain, specified extent and in accordance with a specified criterion, e.g., the ability of a telecommunication device on its 230V AC power port to withstand a surge voltage of 2 kV without being damaged. 3.2 Abbreviations F

49、or the purposes of this ETS, the abbreviations of ETS 300 386-1 I subclause 3.2 apply in addition to the following: AM: Amplitude Modulation. AC: Alternating current DC: Direct current EUT: Equipment Under Test WA: N/A. rms: Root-mean-square. Trnh: Rise tirne (1 O % to 90 %) and hold time (50 % to 50 %) of transient signal (see EN61 000-4 l O). Upso: Voltage measured with a psophometer conforming to Recommendation 0.41 5. 4 Priority of service Where power may be supplied to high priority equipment, “high priority of service applies“, otherwise “normal priority of service